Dantherm CDT 30, CDT 30 S, CDT 40, CDT 40 S, CDT 60 Datasheet
...
MOBILE DEHUMIDIFIERS CDT
CDT 30
CDT 30
MOBILE DEHUMIDIFIER
Function
The CDT 30 is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.
Applications
• Damage service
• Building drying
• Water works
• Dry storing
FEATURES
Dehumidier
• High capacity
• Low energy consumption
• Strong and robust cabinet of powder coated hot galvanized steel
• Epoxy coated evaporator and condenser.
• Adjustable handle
• Plastic bumpers
• Low weight
• Stackable.
• Large wheels
Digital touchpad control panel:
1. On-o switch
2. Reading of room temperature
3. Indicator for normal operation (green lamp)
4. Reading of RH value / setting of RH value
5. Indicator for full water container (yellow lamp)
6. Failure indicator (red lamp)
7. Hour counter / setting of service intervals
8. kWh counter
Water container
• Water container with handles
• Automatic stop when water container is full or removed.
• Permanent drainage can be established with optional ½” hose connection
• Condensate pump in a cassette as optional extra
Electronic control
• Digital touchpad control panel with display
• Accurate hour and kWh counter (reading)
• RH and °C monitoring (reading)
• RH setting
• Easy fault-finding
• Service monitoring function
Defrosting
Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.
MOBILE DEHUMIDIFIERS CDT
740
650
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
only entended as a guide.
table LZT 142 0001, category
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
3
5
1
1
8
9
MATERIAL:
THICKNESS:
WEIGHT:
REV. BY:
DATE:
REF.:
8
Surface appearance according to reference
BEND RADII:
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
CDT 30 MK II
P
A
R
T
N
O
THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN W
HOLE OR IN PART WITHOUT
Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°
740
650
427
10
15
20
25
30
35
°C
L/H
TECHNICAL DATA
Model CDT 30
Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 250 m³/h
Power supply 230 V/50 Hz
Max. ampere consumption 2,7 A
Max. power consumption 0,590 kW
Refrigerant R 134a
Compressor type Rotary
Sound level (at 1 metre) 56 dB(A)
Water container capacity 7 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 32 kg
CAPACITY CURVES
40%
60%
5
0
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6
80%
Specic energy consumption (SEC)
• 0,45 kWh/l at 30°C & 80% RH
• 0,81 kWh/l at 20°C & 60% RH
Accessories
½” drain outlet
Remote hygrostat
Wall bracket
Dual voltage kit
Condensate pump in a cassette
(see separate data sheet)
Also available in this series:
CDT 30 S
CDT 40
CDT 40 S
CDT 60
CDT 90
(see separate data sheets)
DIMENSIONS
426
427
736
740
650
650
506
All dimensions are in mm.
dantherm.com
MOBILE DEHUMIDIFIERS CDT
CDT 30 S
CDT 30 S
MOBILE DEHUMIDIFIER
Function
The CDT 30 S is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws
the humid air into the dehumidifier and through an evaporator coil. When
passing through the evaporator the air is cooled down to below its dew point
temperature, and its content of water vapour is condensed into water, which is
collected in the water container.
Applications
• Damage service
• Building drying
• Water works
• Dry storing
FEATURES
Dehumidier
• High capacity
• Low energy consumption
• Strong and robust cabinet of powder coated hot galvanized steel
• Epoxy coated evaporator and condenser.
• Adjustable handle
• Plastic bumpers
• Low weight
• Stackable.
• Large wheels
• On the back two Ø100 mm flex. air ducts may be connected
(max. length of 5 m) (accessory)
• Built-in 1 kW heating element
• Supplied with high pressure fan
Digital touchpad control panel:
1. On-o switch
2. Reading of room temperature
3. Indicator for normal operation (green lamp)
4. Reading of RH value / setting of RH value
5. Indicator for full water container (yellow lamp)
6. Failure indicator (red lamp)
7. Hour counter / setting of service intervals
8. kWh counter
Water container
• Water container with handles
• Automatic stop when water container is full or removed.
• Permanent drainage can be established with optional ½” hose connection
• Condensate pump in a cassette as optional extra
Electronic control
• Digital touchpad control panel with display
• Accurate hour and kWh counter (reading)
• RH and °C monitoring (reading)
• RH setting
• Easy fault-finding
• Service monitoring function
Defrosting
Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant
being fed through the evaporator.
MOBILE DEHUMIDIFIERS CDT
750
650
750
CDT 30 S MK II
64278.09g
BEND RADII:
24-05-2012
ohr
MATERIAL:
THICKNESS:
WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
R
P
A
R
T
N
O
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
3
5
1
1
9
0
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category
Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY
THIS DRAWING IS FURNISHED WITH THE
UNDERSTANDING THAT THE ESSENCE
THERE OF WILL NOT BE REPRODUCED
IN WHOLE OR IN PART WITHOUT
WRITTEN AUTHORIZATION BY Dantherm A/S.
ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 medium
Angular dimensions without tolerances: ± 1°
750
650
426
10
15
20
25
30
35
°C
L/H
40%
60%
80%
TECHNICAL DATA
Model CDT 30 S
Operating range – humidity 40-100% RH
Operating range – temperature 3-32°C
Air volume 350 m³/h*
Power supply 230 V/50 Hz
Max. ampere consumption 2,6 A
Max. power consumption with heating element 1,56 kW
Max. power consumption without heating element 0,56 kW
Refrigerant R 134a
Compressor type Rotary
Sound level (at 1 metre) 60 dB(A)**
Water container capacity 7 litres
Colour - water container and wheel cap RAL 7015
Colour - front grille RAL 7044
Colour - control panel and bumpers RAL 9005
Protection class IP X4
Filter PPI 15/G1
Wheel size Ø 250 mm
Wheel and water container material PP
Control panel material ABS
Weight 34 kg
*Measured without air ducts mounted.
**Measured with air ducts mounted.
Accessories
½” drain outlet
Remote hygrostat
Wall bracket
Dual voltage kit
Condensate pump in a cassette
Flex. air ducts Ø100 mm
(see separate data sheet)
CAPACITY CURVES
5
0
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6
Specic energy consumption (SEC)
• 0,39 kWh/l at 30°C & 80% RH
• 0,76 kWh/l at 20°C & 60% RH
DIMENSIONS
Also available in this series:
CDT 30
CDT 40
CDT 40 S
CDT 60
CDT 90
(see separate data sheets)
426
736
650
650
506
All dimensions are in mm.
dantherm.com
Loading...