DLM1772Y-DLM1775Y
Integrated Camera Positioning
w/Dual IR Lamps
Installation and Operations Manual
Model Number: DLM1772Y-DLM1775Y
Description: Integrated Camera Positioning System
With dual IR Lamps and
Day/Night 23x, 26x, 36x Zoom
Table of Contents DLM1772Y-DLM1775Y with dual IR Lamps page
1. Installation 3
1.1 Foreword 3
1.2 Safeguards 3
1.3 Function & Features 3
1.4 Pedestal Installation 4
Wiring Diagram 6
Mechanical Diagram and IR Lamp Specifications 7
1.5 Wall Installation 8
Wiring Diagram 8
1.6 Technical Parameters 11
1.6.1 Structure 11
Mechanical Diagram 11
1.6.2 Rotating 11
1.6.3 Electrical 11
1.6.4 Camera 12
2. Operation 12
2.1 Basic Descriptions 12
Operation Procedures 13
2.2 PTZ Functions 15
3. Function Descriptions 15
3.1 Screen Menu (OSD) 15
3.2 Proportional Pan 15
3.3 Auto Scan 15
3.4 Installation Mode 15
3.5 Preset 15
3.6 Preset Tour 15
3.7 Pattern 15
3.8 Position Zero 15
3.9 Low Lux function 15
3.10 Auto Focus 15
3.11 Auto Iris 16
3.12 Backlight Compensation 16
4. Menu Operation 16
5. Menu Description 16
5.1 Main Menu 16
5.2 Second (screen) Menu 17
5.3 Camera Menu 17
5.4 Pan/Tilt Menu 19
5.5 Powering Up 20
5.6 Line Sync 20
5.7 Alarms 20
5.8 Auxiliary 21
5.9 Reset Camera 21
6. Dip Switch Settings 21
6.1 Pan Tilt Controls 21
6.2 Switch SW1 Protocol, Cam Module, Baud Rate Settings 21
6.3 Switch SW2 Receiver/Driver Settings 22
Appendix A Troubleshooting 24
A.1 Video Image 24
A.2 PTZ Controls 24
A.3 Installation 25
1. INSTALLATION MANUAL
1.1 FOREWORD
This manual introduces the function, installation and operation of the integrated high
speed pan tilt camera in details. Please thoroughly familiarize yourself with the
information in this manual prior to installation.
This series pan tilt camera is specially designed for airports, homeland security,
customs, highway etc. It has many features: reliable, stable, airproof, waterproof, acid
water proof, able to withstand high temperature, aging, strong wind and so on. It adapt
to the following harsh conditions, such as high wind power, wide changing temperature
conditions, high electromagnetism and lightning and continuous operating conditions.
This series integrated positioning system includes high speed decoder, pan tilt, shield,
heater, defroster, wiper and integrated DSP ((digital signal processing) camera module
day/night 23x, 26x, 36x optical and 12x digital zoom.
Protocol P/D is employed in the received driver of the integrated positioning system. It
may support standard system platforms such as keyboards and matrix switchers. This
manual will not explain the operation of other devices if connecting with system, please
read the manual of the interfacing product or device.
1.2 SAFEGUARD AND WARNINGS
Prior to installation and use of this product, the following WARNING should be
observed. This product may be only used in specified range in order to avoid any
damage or danger.
Installation and servicing should only be done by qualified service personnel;
It may not be used in temperature range, humidity and power supply outside
the specifications.
Only use replacement parts recommended by factory.
Please use soft cloth to clean the glass. Use neutral cleaner if smear is present
on the glass. No use of strong or corrosive cleanser to avoiding scuffing.
Be cautious when moving P/T unit, never press the drive parts heavily to avoid
pan tilt camera troubles.
The installation bracket should be capable of supporting four times the total
weight of the integrated camera.
Please thoroughly read this manual prior to installation and operation.
1.3 FUNCTIONS AND FEATURES：
Pan tilt camera is made of high strength all-alloy material, waterproof, and able to
withstand high temperature, aging, and erosion.
Accurate motor driving, stable operation, sensitive reaction and accurate
orientation
Includes built-in function menu, to set camera and pan/tilt parameters.
Features video freeze, back light compensation function
Pattern track memory function, may record the preset transfer and all standard
P/T/Z track
Change speed proportionally - Pan/tilt speed and the depth of zoom lens decline
proportionally
128 preset position, with accuracy error less than 0.10
Preset target speed: 1500 /sec for pan, 800 /sec for tilt
Manual control speed: 0.1~1000/sec for pan control, 0.1~800/sec for tilt
Alterable auto scan speed: 10~400 /sec may be set by the in-built menu
8 preset tour functions, dwell time may be set to 2- 60sec
Pan rotation :3600 continuously rotating
Tilt rotation: -85~ +350 rotation, with auto flip function
Manual control speed for pan: 0.10 ~1000/sec
Manual control speed for tilt: 0.10 ~800/sec
Video output: PAL/ NTSC format, composite video: 1V p-p
Baud rate: 1200/2400/4800/9600b
RS-485 communication for control of pan tilt
Built-in wiper, heater, fans, defrost module
Embedded surge and lightning circuitry
Complies with CE, FCC and IP66 standards,
Working temperature: -40 °C ~ +50 °C
1.4 PEDESTAL INSTALLATION
The pedestal installation camera includes the following parts. Inspect each package to
make sure all parts are present.
Integrated pan tilt rotating platform pedestal
Integrated pan tilt 1 pc
Rotating platform（with connect cables）
1 pc
pedestal 1 pc
base bracket 1 pc
connecting cables 1 pc
fixed spanner 1 pc
pedestal water joint 1 pc
manual 1 set
Glove 1 pair
Thread compound 1 roll
Fixed screw Φ5X10mm (for rotate platform) 4 pcs
Φ8mm screws 4 sets
Φ8X38mm bolts 12 sets
Steps of pedestal installation:
STEP 1 Locate the floor or impending base level that may support 4 times the weight of
pan tilt. Fix the screws provided on the floor or firm surface.
STEP 2 fix the pedestal on the floor or impending base level:
STEP 3 Install power supply, video output, RS-485 control input wiring through
waterproof connector plugs, and connect them to the corresponding power supply, video,
RS-485 wiring of the cable provided.
Connect the cable according to the following pinout diagram:
STEP 4 Loosen the four Φ3mm screws on the fixed rotating platform and remove the
transformer fixed board module from the rotating platform. There are four installation holes
under the rotating platform.
Fix the four Φ5x10 fixed screws on the pedestal, then install the connecting cable into
the pedestal and screw it with waterproof BNC plugs. Re-install the transformer board
module on the rotating platform.
STEP 5 Insert the connecting cable of the pan tilt’s pedestal into 2x11 pin plug following
the 2x11 pin plug direction instruction. Then install the three mounting holes of the
pedestal on to the three lugs on the rotating platform and tighten with nuts provided.
STEP 6 Loosen the screw nut cover on the pan tilt’s left side, to expose the 8 DIP dial
switch. Set the protocol, baud rate, address for the pan tilt. Screw the nut cover tightly
after completion of settings.
STEP 7 Turn on the power to check operation.
3
DLM1778 Pedestal Mount
* Inverted View of mount
* Maximum Bearing Weight 100Kg
* Aluminum alloy material
1. Rubber Gasket for top of pole
2. Cable Gland cover
3. Top of mount for installing
DLM1778 Integrated camera system
Dimensional Drawing: (unit: MM)
2
DLM1778 Pedestal Mount
IR Lamp Specifications
Distance: 100 meters
Angle of View: 45
IR Lenses & LEDs per Lamp: 7x 1W;
6 LEDs, 8mm dia.
Voltage: 12VDC
Power Consumption: 6W per IR Lamp
(feeds off main input)
Dimensions dia. x H: 4.25”(108mm) x
3.3”(85mm)
0
1.5 WALL INSTALLATION
The wall installation camera contains following parts. Inspect each package to make
sure all parts are present.
Integrated pan tilt rotating platform wall bracket
Integrated pan tilt 1 pc
Rotating platform（with connect cables）
1 pc
pedestal 1 pc
wall bracket 1 pc
connecting cables 1 pc
fixed spanner 1 pc
pedestal water joint 1 pc
manual 1 set
Glove 1 pair
Thread compound 1 roll
Fixed screw Φ5X10mm (for rotate platform) 4 pcs
Φ8mm screws 4 sets
Φ8X38mm bolts 12 sets
Steps of wall installation
STEP 1 Install the Φ8mm screws on the wall (refer to the following picture)
STEP 2 Install the power supply box on the wall if power supply box is required, then
install the wall bracket on the power supply box. If no power supply enclosure is needed,
install the bracket directly on the wall.
STEP 3 Install power supply, video output, RS-485 control input wiring through the body
of the bracket and connect them to the corresponding power supply, video, RS-485 wiring
of the cable provided.
Connect the cable according to the following pinout diagram:
STEP 4 connect the cables. Connect the cables from the platform wih the power supply
wiring, video wiring, RS-485 control wiring from bracket accordingly.
STEP 5 Installing the platform - Loosen the four Φ3mm screws on the fixed rotating
platform and remove the transformer fixed board module from the rotating platform. There
are four installation holes under the rotating platform.
Check the cables connecting and put them into bracket. Install the four Φ5×10 fixed screws
on the pedestal. Then re-install transformer fixed board module on the rotating platform.
STEP 6 Insert the connecting cable of the pan tilt’s pedestal into 2x11 pin plug following
the 2x11 pin plug direction instruction. Then install the three mounting holes of the
pedestal on to the three lugs on the rotating platform and tighten with nuts provided.
STEP 7 Loosen the screw nut cover on the pan tilt’s left side, to expose the 8 DIP dial
switch. Set the protocol, baud rate, address for the pan tilt. Screw the nut cover tightly
after completion of settings.
STEP 8 Turn on the power to check operation
1.6 TECHNICAL PARAMETERS
1.6.1 Structure parameters:
Integrated pan tilt Aluminum alloy
Rotating platform Aluminum alloy
Bear weight mode top bear
standard bear weight 5Kg
Shield module with housing, defrost device, heater and fans
installation wall mount, pedestal mount
bracket requirement 4 times of the pan tilt’s weight
operating temperature -40ºC ~ 50ºC
Dimension as the following dimension picture
1.6.2 Rotating parameters:
Pan rotation 360ºcontinuous rotation
Tilt rotation +35º ~ -85º unobstructed rotation
Manual control speed
Pan 0.1º ~ 100º/Second manual operation
Tilt 0.1º ~ 80º/Second manual operation
Preset speed
Pan 150º/ Second
Tilt 80º/Second
1.6.3 Electrical parameters
Input voltage 24VAC, 120VAC, 230VAC, 50/60Hz
Input power 50VA
Coaxial cable requirement: 75 ohms resistant; complete copper core conductor;
complete copper shield layer, shield cover range 95%
Heater, defroster, fan, wiper
1.6.4 camera, lens parameters
Hitachi CCD
SONY CCD
~F3.6
~F3.8
Digital Zoom
S/N Ratio
Camera Specifications
Image Sensor ¼”
Resolution 480/550BW TVL 480/570BW TVL 540/650BW TVL
Effective Pixels NTSC 380k / PAL 450k NTSC 630k / PAL 740k NTSC 380k / PAL 440k
Signal Format NTSC/PAL NTSC/PAL NTSC/PAL
Video Output 1V p-p (sync negative) 1V p-p (sync negative) 1V p-p (sync negative)
Lens 23X optical 26X optical 36X optical
Focal Length f=3.6mm(Wide)~82.8mm(Tele)
Aperture F1.6
Min. Working
Distance 100mm(Wide)~1000mm(Tele)
Sync System internal/external (V-lock) internal/external (V-lock) internal/external (V-lock)
Min. Illumination 0.1Color / 0.01BW/LUX 1.0/0.15BW/LUX 0.1/0.01BW/LUX
IRIS Auto/Manual Auto/Manual Auto/Manual
Focus Auto/Manual Auto/Manual Auto/Manual
White Balance
Gain Auto Auto/Manual Auto/Manual
BLC Auto Auto/Manual Auto/Manual
DLM1972 - 23X Day/Night DLM1972 - 26X Day/Night DLM1975 - 36X Day/Night
¼”
f=3.5mm(Wide)~91mm(Tele) f=3.4mm(Wide)~122.4mm(Tele)
F1.6
12X 12X 12X
320mm(Wide)~1500mm(Tele) 320mm(Wide)~1500mm(Tele)
>50dB >50dB >50dB
Auto/Manual Auto/Manual Auto/Manual
¼” SONY CCD
F1.6~F4.5
2. OPERATION
2.1 BASIC DESCRIPTIONS
After connecting wires as per instructions in previous section and turning on power, the
pan tilt camera will display its configured information. And after initialization, the menu
will show “configure OK” information. If the user sets the POWER UP DONE, the
camera will execute this movement and the initial screen disappears; if the user does
not set the POWER UP DONE, the initial screen information will be seen until the
camera receives the control command, then the initial screen will disappear and show
the system communication control is normal. If there is no control command, the initial
screen will disappear after 3 minutes.
Power up display：
VERSION 1.10
PROTOCOL P
ADDRESS 1
COMM
2400.N.8.1
POWER UP DONE
When configuring：
Configure OK:
VERSION
1.10
PROTOCOL P
ADDRESS 1
COMM 2400.
N.8.1
CONFIGURING
VERSION 1.10
PROTOCOL P
ADDRESS 1
COMM 4800.
N.8.1
CONFIGURE OK P:000/T:00
NOTE: 1. VERSION 1.10 is the software version number of the P/T camera, and it will
change as the product’s upgrade.
2. PROTOCOL is PTZ control type - supports P, D protocols, and it will change
as the dial switch chooses different protocol.
3. ADDRESS 1 is control address, may support 256 addresses, and it will
change as the dial switch chooses different address number.
4. COMM 4800.N.8.1 is communication information, 2400 is communication
baud rate, there are 1200, 2400, 4800, 9600 four baud rate for different dial switch.
N.8.1 means no verify, 8 data bytes, 1 dwell position.
Upon successful configuration, user may operate the camera as the following way:
OPERATION PROCEDURE
Pan/Tilt 1. To move via control keyboard, camera will rotate to the
operation direction if the joystick leans to one direction of
up/down/left/right. The speed depends on the distance
between joystick and center. The camera will move slowly to
the operation direction if move the joystick lightly in one
direction. The camera will speed to maximum if the joystick
moves in one direction. The camera will stop when the joystick
returns to the center.
2. To control the DLM1772-DLM1775, use either the DLI6335
Keyboard or if a Matrix Switcher is installed, unit will be
controlled with DLH6330 Keyboard. Matrix Switchers series
box type DLH4200B or bay type DLH4400E features
RS-422/RS-485 Data PTZ control ports.
3. To control via computer software, press the direction key of
control, the camera will rotate to the operating direction. The
speed depends on current speed code. Some software may
implement continuous rotation and some only may implement
dot movement. Please refer to the software instruction
provided by the manufacture for detailed operations. The
DLM1772-DLM1775 may do 3600 continuous pan rotation and
+20~-920 vertical rotations. It will stop rotating when the tilt
limit is reached.
STOP SCAN Preset 96 (hit“9”+“6”+ “Preset”)
PRESET TOUR Preset 98 (hit“9”+“8”+ “Preset”)
AUTO SCAN Preset 99 (hit“9”+“9”+ “Preset”)
ZOOM WIDE 1. Press the ZOOM WIDE button or turn the joystick clockwise
until the image is acceptable
2. Release the button or joystick
ZOOM TELE 1. Press the ZOOM TELE button or turn the joystick
anti-clockwise until the image is acceptable
2. Release the button or joystick
IRIS OPEN Continuously press key OPEN to open iris and increase
brightness gain
IRIS CLOSE Continuously press key CLOSE to close iris and increase
brightness gain
FOCUS NEAR Continuously press key NEAR, focus become near from far, the
image becomes foggy from clear or becomes clear from foggy.
FOCUS FAR Continuously press key FAR, focus become far from near, the
image becomes foggy from clear or becomes clear from foggy.
PRESETS 1. When set presetting, press “preset No.”+
key ”PRESET”(about for 3 seconds)
2. When use presetting, press “preset No.”+ key ”PRESET”
3. Please refer to operation instruction book for controller.
Remarks:
The following stipulations are for presetting,
Preset() function
8-Jan Park position
2-Jan Alarm input
33 180º flip
34 lever home place
77 Open wiper function
78 Close wiper function
79 Open zoom on
80 Close zoom on
81 Auto low lux shift
82 Open law lux shift （B&W menu）
83 Close law lux shift （color menu）
84 Open wide dynamic
85 Close wide dynamic
86 Open Backlight Compensation
87 Close Backlight Compensation
88 Open video freeze
89 Close video freeze
92-93 Scan control limit
94 Exit menu
2. 2 PTZ FUNCTIONS
This series high-speed P/T camera manual pan speed 0.1 º -100 º/second, manual
tilt speed 0.1º ~ 80º/second.
Pan/tilt speed and lens zoom is proportional, darker the lens zoom, slower the
speed is!
The current position of P, T, Z three orientations (presetting positions) may be
stored and repeat use.
3. FUNCTION DESCRIPTIONS
3.1 Screen menu function (OSD)
Camera and pan & tilt may be parameters are displayed by OSD menu
3.2 Proportional pan
Horizontal and tilt speed change automatically with the zoom changes. When wide
zooming, the camera speeds down. When narrow zooming, the camera speeds up to allow
better tracking effect.
3.3 Auto scan
Auto scan refers to the function of 3600 continuous scan the images at certain speed on
the horizontal lever when keeping the pitch angle unchanged. The left and right limits may
be set for continuous scan at certain speed on the horizontal lever.
3.4 Installation mode
The camera may be installed upwards or upside down according to requirements. The
image will always be showed positive on the monitor no matter the installed position.
3.5 Preset
Any position of P/T camera PTZ may be stored. We call it preset (pre-established
position). The preset may be transferred and deleted.
3.6 Preset tour
The P/T camera will transfer pre-established preset 1-8 every 10 second. It will leap
over to next preset position if position in not any of the 1-8.
3.7 Pattern
The PTZ orientation and specific tracking pattern may be stored. The pan & tilt UP,
DOWN, LEFT, RIGHT and the lens’ FAR, NEAR parameters may be stored. Also we may call
the presetting. This function may be used to record and simulate the operator’s operation
process.
3.8 Position Zero
The camera will turn to horizontal and tilt zero by preset 34 when accidental
desynchronizing appears or the operator wants to find zero position during working process.
It may reset the orientation as a convenience for the operator
3.9 Low lux (color / black & white) function
The camera automatically changes CCD lux according to surrounding light. Color image
changes to black & white in low lux; black & white image changes to color in high lux
(camera dependent)
3.10 Auto focus
The camera automatically adjusts lens focus to keep clear image if auto focus mode.
Manually operate FAR or NEAR focus adjustment may also adjust focus. The P/T camera will
recover auto focus adjustment function if operate horizontal, vertical rotation or control
lens zoom.
3.11 Auto iris function
The camera automatically adjusts iris to keep normal brightness in auto iris mode.
Manually operate OPEN or CLOSE iris adjustment button may also adjust iris. The P/T
camera will recover auto adjustment function if operate horizontal, vertical rotation or
control lens zoom.
3.12 Backlight compensation
The object will become black as the shadow if strong light appears in background.
Backlight compensation function may compensate the brightness automatically to dark
objects in bright light background and adjust the brightness background to avoid the image
full of brightness and get clear image. Too strong backlight may make the object illegibility.
4. MENU OPERATION
This series camera has in-built menu to setup to camera and lens’ parameter. In this
chapter, you will get a whole knowledge of the camera, and get some useful operation
skills.
The basic operation of the menu includes: move menu bar, enter next menu, turn back
to previous menu, change setting value, confirm change and cancel change.
This P/T camera opens menu by preset 95 and exit by preset 94 according to P control
protocol. Please refer to controller instruction book for other control equipments.
Press “9”+”5”+”PRESET”
Press key 95+ PRESET to enter pan tilt camera menu
Press “9”+”4”+”PRESET”
Press key 94+ PRESET to exit pan tilt camera menu
5. MENU DESCRIPTION
The DLM1772-DLM1775 series P/T camera system is set by default to P/D protocol. Use
preset position No.95 to open the main menu. For other protocols, please refer to protocol
instruction.
NOTE:
1. “< >”symbol means it contains next menu
2. use “up, down” key to move cursor “→”, use “OPEN or CLOSE” key to confirm or exit the
menu
3. when press “OPEN” key, the cursor becomes”→”, then may use “UP or DOWN” key to
amend the parameter; press OPEN key when finish your amendment.
5.1 MAIN NENU
<SYSTEM INFORMATION>
<CAMERA>
<PAN/TILT>
<POWER UP>
<LINE SYNC>
<ALARM>
<AUX>
RESET CAMERA
〈SYSTEM INFORMATION 〉
〈CAMERA 〉
〈PAN/TITL 〉
〈POWER UP〉
〈LINE SYNC〉
〈ALARM〉
〈AUX〉
RESET CAMERA
EXIT
5.2 SECOND MENU I
P/T TYPE
COMM
PROTOCOL
ADDRESS
VERSION
AUTO EXIT TIME
BACK
SYSTEM INFORMATION
CAMERA TYPE
COMM 4800、N、8、1
PROTOCOL P
ADDRESS 1
VERSION 1.10
AUTO EXIT TIME 5
BACK
NOTE: Except “AUTO EXIT TIME”, items may not be modified only displayed in the menu.
5.3 CAMERA MENU I
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
SHARNESS LEVEL
BACKLIGHT COMP
VIDEO FREEZE
DAY/LIGHT MODE
STABILIZER
WDR
<NEXT>
AUTO FOCUS ON
ZOOM LIMIT X26
ZOOM SPEED 5
SHARPNESS LEVEL 10
BACKLIGHT COMP OFF
VIDEO FREEZE OFF
DAY/NIGHT MODE AUTO
STABILIZER ON
WDR ON
〈NEXT〉
BACK
CAMERA
BACK
NOTE: stabilizer and WDR are camera module dependent, if the function shows in the
menu; it is available
AUTO FOCUS Default Setting: ON
FOCUS MODE: ON and OFF
ZOOM LIMIT Default Setting: X18
Zoom Limit displays different limitations with different cameras
ZOOM SPEED Default Setting: 5
Range of zoom speed is between 0~7, different camera shows different zoom
SHARPNESS LEVEL Default Setting: 10
Sharpness lever is between 0~15 and AUTO
BACKLIGHT COMP Default Setting: OFF
Backlight COMP: ON and OFF
VIDEO FREEZE Default Setting: OFF
Video Freeze Mode: ON and OFF
DAY/NIGHT Default Setting: AUTO
Day/Night Mode: Auto-change, Day color only, Night black/white only
STABILIZER Default Setting: OFF
AUTO WHITE BALANCE AUTO
Stabilizer Mode: ON and OFF, Camera with this function displays in menu
WDR Default Setting: OFF
WDR Model (for 23X HITACHI VK-S454): ON and OFF, it works when the backlight
compensation is OFF.
5.3.1 CAMERA MENU II
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
SHUTTER MODE
SHUTTER SPEED
AGC MODE
<NEXT>
AUTO IRIS AUTO
AUTO IRIS LEVEL 12
AUTO IRIS PEAK 10
SHUTTER MODE AUTO
SHUTTER SPEED 1/50
AGC MODE AUTO
GAIN 2db
AUTO WHITE BALANCE
R GAIN
B GAIN
R GAIN 210
B GAIN 157
BACK
BACK
AUTO IRIS Default Setting: AUTO
Auto Iris: AUTO and MAN
AUTO IRIS LEVEL Default Setting: 12
When the auto iris is under the circumstances of MAN, 0~17 may be selected.
AUTO IRIS PEAK Default Setting: 10
When the auto iris is under the circumstances of MAN, 0~10 may be selected
SHUTTER MODE Default Setting: AUTO
Shutter Mode: AUTO and MAN
SHUTTER SPEED Default Setting: 1/50
When shutter speed under the circumstances of MAN, 1/1~1/10000 may be selected,
which is according to the camera parameter.
AGC MODE Default Setting: AUTO
AGC MODE: Auto and MAN
GAIN Default Setting: 2db
Gain Level may be selected between 0~28
AUTO WHITE BALANCE Default Setting: AUTO
Auto White Balance Mode: AUTO and MAN
R GAIN Default Setting: 21
When auto white balance is under the circumstance of MAN, 0~255 may be selected.
B GAIN Defaulting Setting: 157
When auto white balance is under manual control, 0~255 may be selected
5.4 PAN/TILT MENU
AUTO FLIP
PROPORTIONAL PAN
PARK ACTION
PARK TIME
PRESET TOUR TIME
SCAN SPEED
MANUAL STOPS
ANGLE DISPLAY
SET AZIMUTH ZERO
AUTO FLIP ON
PROPORTIONAL PAN OFF
PARK ACTION NONE
PARK TIME 30min
PRESET TOUR TIME 5s
SCAN SPEED 10d/s
MANUAL STOPS OFF
SCAN STOPS OFF
ANGLE DISPLAY ON
SET AZIMUTH ZERO
BACK
PAN/TILT
BACK
AUTO FLIP Default Setting: ON
Auto Flip Mode: ON and OFF
PROPORTIONAL PAN Default Setting: OFF
Proportional Pan Mode: ON and OFF
PARK ACTION Default Setting: NONE
Park Action Mode: there are 12 modes such as NONE, 1PRESET~8PRESET, SCAN,
PRETOUR, PATTERN and so on
PARK TIME Default Setting: 30minutes
Park Time: 5~60 sec selectable
SCAN SPEED Default Setting: 10d/s
Scan Speed: 1 d/s~40 d/s selectable
MANUAL STOPS Default Setting: OFF
Manual Stops Mode: ON and OFF
SCAN STOPS Default Setting: OFF
Manual Stops Mode: ON and OFF
ANGLE DISPLAY Default Setting: ON
Angle Display Mode: ON and OFF, orientation of P/T and camera zoom may display when it
is ON.
SET AZIMUTH ZERO
Turn the camera to the position that would be defined to be azimuth zero at first, then
press OPEN key to confirm it.
5.5 POWERING UP ACTION
LINE SYNC
LINE SYNC PHASE
ALARM 1
ALARM 2
POWER UP ACTION
POWER UP TIME
BACK
POWER UP ACTION NONE
POWER UP TIME 2min
BACK
POWER UP
POWER UP ACTION Default Setting: NONE
Power Up Action Mode: NONE, 1PRESET~8PRESET, SCAN, PRETOUR, PATTERN
selectable.
POWER UP TIME Default Setting: 2minutes
Power Up Time may be selected from 2s to 10s
5.6 LINE SYNC
LINE SYNC
OFF
LINE SYNC
LINE SYNCPHASE
BACK
0
BACK
LINE SYNC Default Setting: ON
LINE SYNC MODE: ON and OFF
LINE SYNC PHASE Default Setting: 0
Line Sync Phase: 0~359 selectable
5.7 ALARM
ALARM
ALARM1
ALARM2
BACK
ALARM1
NONE
NONE
BACK
Default Setting: NONE
Alarm1: NONE, 1PRESET~8PRESET, SCAN, PRETOUR and PATTERN selectable
5.8 AUXILLIARY
WIPER
INFRARED
AUX1 MODE OFF
AUX2 MODE OFF
BACK
AUX
BACK
WIPER Default Setting: OFF
Wipe input is relay input, the mode: ON and OFF
INFRARED Default Setting: OFF
Infrared input is relay input, the mode: ON and OFF
5.9 RESET CAMERA.
When users choose this item, camera will reset to the default setting.
6. DIP SWITCH SETTING
6.1 Pan/tilt Controls
Note: When one control bus controls several (more than 2) Pan/Tilt cameras,
it needs a 120ohm resistance at +/- terminals Com RS-485 in the farthest end of pan
tilt camera in order to ensure the normal work of control signal.
6.2 Switch setting for SW1
Note: Switch SW1 is used to set protocol, camera and baud rate
Protocol, camera,
baud rate
1 2 3 4 5 6 7 8
SW1 setting
PELCO-P Protocol ON OFF -- -- -- -- -- --
PELCO-D Protocol OF ON -- -- -- -- -- --
SONY camera
HITACHI camera
-- -- ON OFF ON OFF -- --
-- -- OFF ON ON OFF --
1200 -- -- -- -- -- -- OFF OFF
2400 -- -- -- -- -- -- ON OFF
4800 -- -- -- -- -- -- OFF ON
9600 -- -- -- -- -- -- ON ON
6.3 Switch setting for SW2
Note: Switch SW2 is used to set receiving address.
Protocol P addresses setting:
Switch setting
Address
SW2-
SW2-
SW2-
SW2-
1 OFF OFF OFF OFF OFF OFF OFF OFF
2 ON OFF OFF OFF OFF OFF OFF OFF
3 OFF ON OFF OFF OFF OFF OFF OFF
4 ON ON OFF OFF OFF OFF OFF OFF
5 OFF OFF ON OFF OFF OFF OFF OFF
6 ON OFF ON OFF OFF OFF OFF OFF
7 OFF ON ON OFF OFF OFF OFF OFF
8 ON ON ON OFF OFF OFF OFF OFF
9 OFF OFF OFF ON OFF OFF OFF OFF
10 ON OFF OFF ON OFF OFF OFF OFF
11 OFF ON OFF ON OFF OFF OFF OFF
12 ON ON OFF ON OFF OFF OFF OFF
13 OFF OFF ON ON OFF OFF OFF OFF
14 ON OFF ON ON OFF OFF OFF OFF
15 OFF ON ON ON OFF OFF OFF OFF
16 ON ON ON ON OFF OFF OFF OFF
SW2-
SW2-
SW2-
SW2-
17 OFF OFF OFF OFF ON OFF OFF OFF
18 ON OFF OFF OFF ON OFF OFF OFF
19 OFF ON OFF OFF ON OFF OFF OFF
20 ON ON OFF OFF ON OFF OFF OFF
21 OFF OFF ON OFF ON OFF OFF OFF
22 ON OFF ON OFF ON OFF OFF OFF
23 OFF ON ON OFF ON OFF OFF OFF
24 ON ON ON OFF ON OFF OFF OFF
25 OFF OFF OFF ON ON OFF OFF OFF
26 ON OFF OFF ON ON OFF OFF OFF
27 OFF ON OFF ON ON OFF OFF OFF
28 ON ON OFF ON ON OFF OFF OFF
29 OFF OFF ON ON ON OFF OFF OFF
30 ON OFF ON ON ON OFF OFF OFF
31 OFF ON ON ON ON OFF OFF OFF
32 ON ON ON ON ON OFF OFF OFF
----- ---- ---- ---- ----- ---- ---- ---- ---255 OFF ON ON ON ON ON ON ON
256 ON ON ON ON ON ON ON ON
Protocols D address setting:
Address
SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8
1 ON OFF OFF OFF OFF OFF OFF OFF
2
3
4
OFF
ON
OFF
5 ON OFF ON OFF OFF OFF OFF OFF
6
7
8
9
10
11
12
13
14
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
15 ON ON ON ON OFF OFF OFF OFF
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
----
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
---254 OFF ON ON ON ON ON ON ON
255 ON ON ON ON ON ON ON ON
Switch setting
ON OFF OFF OFF OFF OFF OFF
ON OFF OFF OFF OFF OFF OFF
OFF ON OFF OFF OFF OFF OFF
ON ON OFF OFF OFF OFF OFF
ON ON OFF OFF OFF OFF OFF
OFF OFF ON OFF OFF OFF OFF
OFF OFF ON OFF OFF OFF OFF
ON OFF ON OFF OFF OFF OFF
ON OFF ON OFF OFF OFF OFF
OFF ON ON OFF OFF OFF OFF
OFF ON ON OFF OFF OFF OFF
ON ON ON OFF OFF OFF OFF
OFF OFF OFF ON OFF OFF OFF
OFF OFF OFF ON OFF OFF OFF
ON OFF OFF ON OFF OFF OFF
ON OFF OFF ON OFF OFF OFF
OFF ON OFF ON OFF OFF OFF
OFF ON OFF ON OFF OFF OFF
ON ON OFF ON OFF OFF OFF
ON ON OFF ON OFF OFF OFF
OFF OFF ON ON OFF OFF OFF
OFF OFF ON ON OFF OFF OFF
ON OFF ON ON OFF OFF OFF
ON OFF ON ON OFF OFF OFF
OFF ON ON ON OFF OFF OFF
OFF ON ON ON OFF OFF OFF
ON ON ON ON OFF OFF OFF
ON ON ON ON OFF OFF OFF
OFF OFF OFF OFF ON OFF OFF
---- ---- ---- --- ---- ---- ----
Appendix A TROUBLESHOOTING
1. Image
Problem: No image displayed on monitor?
→First check if the power supply wire connection, voltage, indicator and P/T
camera work well, and then check the video wires, or it may be a problem with
the cam module.
Problem: Image becomes black after self check, but may be controlled
→Control system may have changed the camera iris parameters. Enter the
camera menu then reset camera.
Problem: Image becomes foggy when P/T camera connects with hard disk video
recorder.
→Maybe it is related with the compressed card of hard disk video recorder.
Problem: abnormal display of image
→Check the video connecting wires, connecting sockets and camera flat wires.
Problem: Iris is small with many snowflakes after connection
→The camera parameter has changed. Please enter the menu to reset the
camera.
Problem: The camera may only focus in one position, other positions do not focus.
→Change the position of P/T and see if condition persists. If yes, it may be
caused by camera control drive focus system.
Problem: image may not be clearly seen even at MAX. Zoom
→Maybe electronic zoom open or the observed object is too close for imaging.
Problem: the image is reddish or greenish. Does the WB parameter change?
→The camera parameter changed. Enter the menu to reset the camera.
Problem: the color - to black & white function in camera does not change
→Rotate control to other angle and see if condition changes. If not, reset camera
parameter.
2. Control
Problem: the single pan tilt camera may not be controlled by keyboard or other
control equipment?
→First check if control line RS-485 is well connected to designed position with
right direction. Then check the control equipment and P/T control protocol, baud
rate and address. If it still may not be controlled, use elimination to check
whether the control equipments or camera has troubles.
Problem: single pan tilt may be controlled but multi-cameras may not be controlled
→It may be caused by reflection of signal RS-485. Merge a 120 ohm resistance to
the 485 terminal control wires of the farthest camera.
Problem: other controls are normal except it may not rotate at a direction.
→First check if any mechanical troubles without powering unit. If it may run well,
check if the belt broke or loose. If yes, it is caused by the control decoder board
troubles.
Problem: the pan tilt automatically rotates after power on.
→First check if the power on mode is auto scan mode; if not, firstly cut RS-485
control lines to see if it persists. If it stopped, it may be caused by the scrambled
code from controller or interference to RS-485 lines.
Problem: the provided keyboard software may control, but the DVR may not control
or only may control some?
→DVR control protocol is not compatible with the product or the function is not
complete.
Problem: why does the same pan tilt have different control speeds at different hard
disk video recorder?
→Speed command codes in control software of DVR are different.
Problem: DVR may not control speed of pan tilt
→Control command code of control software in DVR only has a fixed speed.
Problem: the camera rotates disorderly. The image is blackish or whitish.
→There is interference with the RS-485 lines, check the equipment in the lines
such as optical transmitter and receiver.
Problem: the pan tilt camera may be controlled normally in the morning and evening,
but it may not be controlled at the noon of summer.
→High temperature may cause lower down of control line anti-jamming or change
to control equipment and CMOS chips parameters to create problems. Check if the
temperature is over than the specified limit and if fan is functioning.
Problem: pan tilt camera continuously does self-check up after power on
→The supply voltage is too low or the power is not enough. The matching
transformer of 2.5A 24VAC is recommended. The installation distance should be
no more than 30m.
3. Installation
Problem: what is the maximum distance of video wire and what requirements does it
have to wire materials?
→The video wire also has inner loss as the power wire. The more the wire is and
the small the specification is, the worse loss it will be. The high the signal
frequency is, the obvious the loss is. The normal video wires models and the MAX.
Transmission distance is listed in following table:
Video wire
Max. distance Video wire model Max. distance
model
75-2 About 150m 75-5 About 370m
75-3 About 200m 75-7 About 500m
75-4 About 270m
75-9 About 680m
Problem: what wire and transmission distance should RS-485 control line take?
→Transmission distance of RS-485 is related to wire diameter and transmission
speed. Max. Transmission distance for RS-485 is 1200m according to the specified
9600b/s transmission speed for 1.0mm 2 UTP.
Remarks: the same model wires may be different for produced by different
manufacturers. Above data is the normal wire transmission
reference distance.
Loading...