CCS 7800
Installation Manual
Camera Control System
CP 7801 Camera Control Package
Version 1.5
User Manual
Danish Interpretation Systems DIS
Danish Interpretation Systems Installation Manual
Copyright © 2007/2010 DIS CP 7801 USER MANUAL - REV H.DOC 14-08-2013
No part of this publication may be reproduced or utilised in any form or by any means without permission in writing from the
publisher.
Danish Interpretation Systems Installation Manual
List of Contents
List of Contents ......................................................... 3
Introduction .............................................................. 4
CP 7801 Package .................................................. 4
Product Description ............................................ 4
Part List ................................................................... 5
Important ................................................................... 5
Charging the iPod Control (IPC) ......................... 5
Use with SW 6000, ECA application................... 6
Schematic ................................................................ 6
Setting up the system ......................................... 6
Using the iPod Control ....................................... 8
Main Menu ................................................................ 9
Instant Camera Control ...................................... 9
Camera Presets Setup ....................................... 10
Setup System ......................................................... 11
Save/Recall Layouts ........................................... 11
Multiple cameras ................................................... 19
Extron MSW Mini Switcher Series ................. 19
Extron ISS 506 Seamless Switcher ................ 20
Changing of Wireless Channel of WR ............. 21
VISCA Control Cables configuration with Sony
cameras ..................................................................... 22
Trouble shooting ................................................... 23
.
After the system is setup ................................ 11
Use with CU 60xx, direct connection.............. 12
Schematic ............................................................. 12
Setting up the system ...................................... 12
Using the iPod Control .................................... 13
Main Menu .............................................................. 13
Instant Camera Control .................................... 14
Camera Presets Setup ....................................... 15
Setup System ......................................................... 16
Assign Seats ........................................................... 17
Save/Recall Layouts ........................................... 18
After the system is setup ................................ 18
Copyright © 2007/2010 DIS CP 7801 USER MANUAL - REV H.DOC 14-08-2013
No part of this publication may be reproduced or utilised in any form or by any means without permission in writing from the
publisher.
Danish Interpretation Systems Installation Manual
4
Introduction
CP 7801 Package
CP 7801 Camera Control Package consists of the following items:
• iPod touch with preloaded SW 7810 Camera Control Software
• Camera System Control Unit with preloaded SW 7820 Camera Control Software
• Wireless Router
The CP 7801 Camera Control Package is part of the CCS 7800 Camera Control System. Further products
might be added to the Camera Control System
Product Description
The Camera Control Package consist of a controller, a wireless router and an iPod Touch user interface
for setting up the camera presets.
The package supports the universal Visca protocol for camera control and up to 4 cameras can be
controlled. The Sony EVI-D70P is an example of a camera using this protocol.
If more than one camera is used a video switcher is needed. The CP 7801 supports control of the Extron
ISS 506 Seamless Switcher and Extron MSW Mini Switcher Series.
The iPod Touch Interface is used for programming and store camera presets into the camera system
controller. When using multiple cameras multiple presets can be stored for each seat.
The System Control Unit stores the presets for the camera and controls the camera movement as well as
controlling an optional video switcher.
The System control unit is connected directly to the CU 6005/11 Control Unit to the RS232 output or
when using the SW 6000 Conference Software connected to the ECA application's RS232 output.
The system can store camera presets for up to 400 seats. When the presets are stored, that camera’s will
move according to the microphones switched on at the seat.
Preset 400 is the overview preset the system will choose, if no microphone is turned ON or the number of
turned on microphones are larger than the settings made.
For each seat multiple presets (up to 4) can be made. The first preset is the one used if the camera is
‘free’. If the camera is not ‘free’ the second preset is automatically used and so on.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
5
Product Description
Product
iPod control (IPC)
iPod Touch 16GB
USB cable for iPod touch
SW 7810 Software (Preloaded)
Wireless Router (WR)
Linksys wireless E2500
Cable, LAN, 2 m
Power Supply, 12V, 1A
System Control Unit (SCU)
AMX NI-700
SW 7820 Software (Preloaded)
Power Supply, 12V, 1A
Cables
Cable, Control Unit, RS-232-> Visca, 2 m
Cable, Control Unit, RS-232-> CU, 2 m
Adapter
Adapter, RS-232(F)/RS232(F)-> ECA
Part List
Important
It is important, that the settings in the iPod (IPC): ‘Settings/CF iViewer’ are not changed. If changed the
‘DIS Camera Control’ software might be deleted in the iPod and the iPod has to be send to factory for
upload of new software.
The “Adapter, RS-232(F)/RS232(F)-> ECA”, which are used when CP 7851 Camera Control Package is
connected to ECA application in SW 6000, has to be mounted in the PC end of the RS-232 cable between
Camera System Control Unit and the PC.
Charging the iPod Control (IPC)
Connect the iPod Touch to a PC using the USB cable for charging the unit.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
6
#
Description
Comment or picture
1.
Connect the system as shown in above schematic ‘Single
Camera, ECA connection’, using the cables supplied.
The Visca cable from the Camera shall be connected to COM 2
on the SCU.
2.
Change the SW 6000 -ECA settings:
Baud Rate:
Use with SW 6000, ECA application
Schematic
Setting up the system
The RS 232 connector on the PC running the ECA shall be
connected to COM1 on the SCU using the RS 232 cable plus the
RS232 adapter. NOTE that the adaptor has to be mounted in
the PC end of the RS-232 cable.
9600
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
7
3.
Insert command line parameter in the SW 6000 -CUI shortcut:
4.
Start the SW 6000 applications (CUA, CUI and ECA)
5.
Turn on power to the Wireless Router, the Camera Controller
and the Camera(s)
-ALLMICOFF
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
8
6.
Turn on power to the iPod and select Wi-Fi
7.
Choose the:
network
The Linksys has to be powered up
and connected to the Camera
Control Unit
8.
Start “CF iViewer” on the iPod.
‘Touch’ the screen to Start
9.
Select
Using the iPod Control
‘DIS CP 7801-xxx’
ECA Mode
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
9
10.
The Main Menu window will be shown and consist of the
11.
The “Instant Camera Control” is used for operating the
Main Menu
following menus:
Instant Camera Control
Camera Presets Setup
Setup System
Save/Recall Layouts
Instant Camera Control
cameras manual if desired.
Select which camera to operate using the four camera
buttons.
The camera can now be operated using the arrow buttons
for UP/Down and Left/Right movement. The speed of the
movement as well as Zoom In/Out can be adjusted.
Use the icon in the top left corner to return to the Main
Menu
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
10
12.
The screen is used to save the preset for each microphone.
‘Select Seat’ sub page
Camera Presets Setup
How to save presets:
1. Turn on one microphone (the number will be shown
in the “seat no.” field).
2. Click on the ‘Camera Control’ button to switch to the
‘Camera Control’ sub page
3. Select the camera to use.
4. Move the camera to a desired position
5. Press “Save”. The Preset for the seat is now saved.
6. Repeat step 3-5 for more camera presets for the
same seat if desired
7. Turn of the microphone and repeat the steps 3-6 for
the next microphone.
8. Continue step 3-6 for all microphones (seats)
9. Turn off all microphones
10. Select “Save”. Preset 400 shall now be saved for
camera 1 (preset 400 is the preset for the overview
position).
11. Go to ‘Room Layouts’ and save the layout.
Instead of switching microphones on/off as described above
the seat can also be selected using the keypad on the ‘Select
Seat’ sub page. And then the next seat can be selected using
the buttons ‘select seat’: prev/next
The ‘Test seat preset’ is used to recall the stored camera
preset for the selected seat.
‘Camera Control’ sub page
The ‘Delete’ button deletes a stored preset
Use the icon in the top left corner to return to the Main Menu
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
11
13.
No. of Cameras
changed.
Use the icon in the top left corner to return to the Main Menu
14.
When camera presets has been made the layout can be
Setup System
Select the number of cameras connected (1 to 4)
Max. NOM to Overview
Select the number of microphones which can be opened
before the system switches to the overview picture (1 to 8)
Overview delay (sec)
Adjusting the delay before switching to the overview picture
(0-10 sec)
Tracking ON/OFF
When set to OFF the cameras will not move bases on
opening of the microphones. Default is ON
Change DIS connection
Brings the screen, where the connection mode can be
Save/Recall Layouts
stored in the Camera System Control Unit.
Up to three layouts can be saved.
The ‘Save’ button saves the current preset to the selected
‘Layout x’ into a file on the Camera System Control Unit.
The ‘Recall’ button recalls the selected ‘Layout x’ and
overwrites the current presets.
Use the icon in the top left corner to return to the Main Menu
After the system is setup
After having set up all seat presets and saved the Layout (s) the system is ready to use.
The iPod (IPC) and the Wireless Router (WR) can be switched Off as they are only needed for setting up
the system.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
12
#
Description
Comment or picture
15
Connect the system as shown in above schematic ‘Single
Camera, CU 6005/11 connection’, using the cables supplied.
The Visca cable from the Camera shall be connected to COM 2
on the SCU.
16
On the CU 60xx do the following setting:
Set Baud Rate:
Save configuration
Restart the CU 60xx
17
Turn on power the Wireless Router, the Camera Controller
and the Camera(s)
If for any reason controlling of the camera(s) is needed during the meeting, the IPC and the WR shall not
be switched Off.
Use with CU 60xx, direct connection
Schematic
Setting up the system
The RS 232 connector on the CU 6005/11 shall be connected
to COM1 on the SCU using the RS 232 cable.
19200
using the controls and LCD display on the front plate of the
central unit.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
13
18.
Turn on power to the iPod and select Wi-Fi
19.
Choose the:
network
The Linksys has to be powered up
and connected to the Camera
Control Unit
20.
Start “CF iViewer” on the iPod.
‘Touch’ the screen to begin and select
21.
The Main Menu window will be shown and consist of the
Using the iPod Control
‘DIS CP 7801-xxx’
Direct CU Mode
Main Menu
following menus:
Instant Camera Control
Camera Presets Setup
Setup System
Assign Seats
Save/Recall Layouts
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
14
22.
The “Instant Camera Control” is used for operating the
Instant Camera Control
cameras manual if desired.
Select which camera to operate using the four camera
buttons.
The camera can now be operated using the arrow buttons
for UP/Down and Left/Right movement. The speed of the
movement as well as Zoom In/Out can be adjusted.
Use the icon in the top left corner to return to the Main Menu
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
15
23.
The screen is used to save the preset for each microphone.
‘Select Seat’ sub page
Camera Presets Setup
How to save presets:
1. Assign seats. Please refer to the menu ‘Assign Seats’
later in this chapter
2. Turn on one microphone (the number will be shown
in the “seat no.” field).
3. Click on the ‘Camera Control’ buttons to switch to the
‘Camera Control’ sub page
4. Select the camera to use.
5. Move the camera to a desired position
6. Press “Save”. The Preset for the seat is now saved.
7. Repeat step 4-6 for more camera presets for the
same seat if desired
8. Turn of the microphone and repeat the steps 4-7 for
the next microphone.
9. Continue step 4-7 for all microphones (seats)
10. Turn off all microphones
11. Select “Save”. Preset 400 shall now be saved for
camera 1 (preset 400 is the preset for the overview
position).
12. Go to ‘Room Layouts’ and save the layout.
Instead of switching microphones on/off as described above
the seat can also be selected using the keypad on the ‘Select
Seat’ sub page. And then the next seat can be selected using
the buttons ‘select seat’: prev/next
The ‘Test seat preset’ is used to recall the stored camera
preset for the selected seat.
The ‘Delete’ button deletes a stored preset
‘Camera Control’ sub page
Use the icon in the top left corner to return to the Main Menu
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
16
24.
No. of Cameras
changed.
Use the icon in the top left corner to return to the Main Menu
Setup System
Select the number of cameras connected (1 to 4)
Max. NOM to Overview
Select the number of microphones which can be opened
before the system switches to the overview picture (1 to 8)
Overview delay (sec)
Adjusting the delay before switching to the overview picture
(0-10 sec)
Tracking ON/OFF
When set to OFF the cameras will not move bases on
opening of the microphones. Default is ON
Change DIS connection
Brings the screen, where the connection mode can be
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
17
25.
This page is used to assign a seat number to each
Assign Seats
microphone unit. When connected to the CU, the icon in the
top right corner shall shown connection (no red color and no
warning sign).
The ‘Status’ info will show the number of connected
microphone and how many of those which has been
assigned a seat number:
assigned/total number of microphones
How to assign seats:
1. Select “Seat Setup is OFF. Push to turn ON”
2. Select “yes” to “Clear existing Seat data and reassign
all seats?”
3. Activate a microphone. The number of the
microphone is shown. Together with the text ‘Seat
Unassigned’
4. Select “Enter Seat number”
5. Type in the seat number to be used for this
microphone and select
6. “Assign Seat number”
7. Turn of the microphone
8. Repeat step 3-7 for all microphones
9. Select ‘Seat Setup is ACTIVE. Push to turn OFF’
10. Select ‘Save configuration’
When activating/deactivating the microphone the serial
number and seat number for the microphone is shown.
Use the icon in the top left corner to return to the Main Menu
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
18
26.
Changing/Replacing a seat
For changing or replacing a seat:
Use the icon in the top left corner to return to the Main Menu
27.
When camera presets has been made the layout can be
1. Select “Seat Setup is OFF. Push to turn ON”
2. Select “no” to “Clear existing Seat data and reassign
all seats?”
3. Activate a microphone. The number of the
microphone is shown. Together with the text ‘Seat
Unassigned’
4. Select “Enter Seat number”
5. Type in the new seat number to be used for this
microphone and select
6. “Assign Seat number”. If the seat is already in use a
warning message will be shown
7. Select ‘Save configuration’
Save/Recall Layouts
stored in the Camera System Control Unit.
Up to three layouts can be saved.
The ‘Save’ button saves the current preset to the selected
‘Layout x’ into a file on the Camera System Control Unit.
The ‘Recall’ button recalls the selected ‘Layout x’ and
overwrites the current presets.
Use the icon in the top left corner to return to the Main Menu
After the system is setup
After having set up all seat presets and saved the Layout and Seat Configurations the system is ready to
use. The iPod (IPC) and the Wireless Router (WR) can be switched Off as they are only needed for setting
up the system.
If for any reason controlling of the camera(s) is needed during the meeting, the IPC and the WR shall not
be switched Off.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
19
Multiple cameras
If more than one camera is used a video switcher is needed. The CP 7801 supports control of the Extron
ISS 506 Seamless Switcher and Extron MSW Mini Switcher Series. Any video switcher using ‘contact
closure’ control can be used.
Up to four cameras can be connected to the System Control Unit (SCU).
The Sony EVI Cameras operate in a daisy-chain configuration, the first unit in the chain will have Identity
"no 1", the second unit will have Identity "no 2" and so on.
Extron MSW Mini Switcher Series
The switcher is controlled with ‘contact closure’ control. The ‘Contact’ connector on the MSW Switcher is
connected to the ‘I/O ports’ on the ‘System Control:
’
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
20
Extron ISS 506 Seamless Switcher
This switcher is connected using LAN connection. The Switcher has to be set to use IP 192.168.10.111
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
21
#
Description
Comment or picture
28.
Connect a PC to the Wireless
Router using one of the four
LAN ports and turn on power
to the Linksys
29.
Open Internet Explorer and
type:
Login:
Password:
This will open a login screen on the Router
30.
Select ‘Wireless’ page and
change
31.
Reboot the Linksys.
Changing of Wireless Channel of WR
http://192.168.10.1
(leave empty)
Change to another Wireless
Channel
Press ‘Save Settings’ in the
button on the screen.
admin
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
22
VISCA Control Cables configuration with Sony cameras
Below is VISCA cables configuration for both RS-422 and RS-232 for Sony cameras.
Manual 01 19 78010
Danish Interpretation Systems Installation Manual
23
‘Touch Screen to begin’ on iPod does not open the
‘Main Menu’
1. Check ‘Settings/WI-FI’. The ‘DIS CP 7801-
xxx. Shall be connected
The camera does not move when controlling from
the ‘Instant Camera Control’ menu
1. Check that the Visca cable from the camera
is connected to COM2 on the SCU.
2. Reboot the camera
When switching On microphones, the seat no. does
not show up in the ‘Camera Presets Setup’ (direct
1. Check Baud rate setting on the CU 60xx
2. Check RS 232 cable from SCU to CU 60xx
3. Check the ‘link’ icon in the ‘Assign Seats’
menu
When switching ON microphones, the seat no. does
not show up in the ‘Camera Presets Setup’ (ECA
1. Check Baud rate setting on the ECA
application.
3. Check RS 232 cable from SCU to ECA
The ‘link’ icon in the ‘Assign Seats’ menu does
shown no connection to the CU
1. Check RS 232 cable from SCU to CU 60xx
2. Check Baud rate setting on the CU 60xx
(19200 Baud).
The iPod will not connect to the Wireless Router or
the connection is un-stable
1. Change the ‘Wireless Channel’ on the
router. Please refer to the section ‘Change
Wireless Channel of Wireless Router’.
No camera movement when pressing the ‘Speak’
button the the microphone
1. Check, that the system in not in ‘Seat Setup’
mode (for connection mode: Direct CU) in
4. Check that ‘Tracking ON’ is activated in the
‘Setup System’ menu
Trouble shooting
mode)
mode)
2. Check that the RS-232 Adaptor is mounted
in the PC end of RS-232 cable
the ‘Assign Seat’ menu.
2. Check that a ‘Camera’ preset is made for the
seat
3. Check, that the Camera is connected and
working using the ‘Instant Camera Control’
menu.
Manual 01 19 78010
Loading...