Danfoss Electronics BD80F Data Sheet

Datasheets

BD80F

Direct Current Compressor

R134a 12/24V DC

General

Code number (without electronic units) 101Z0280

Electronic unit - High Speed 101N0390, 28 pcs: 101N0391

Compressors on pallet 150

Application

Application LBP

Evaporating temperature °C -30 to -5

Voltage/max. voltage VDC 9.6 - 17 / 21.3 - 31.5

Max. condensing temperature continuous (short)

Max. winding temperature continuous (short) °C 125 (135)

Cooling requirements

Application LBP MBP HBP

32°C S – –

38°C S – –

43°C S – – Remarks on application:

Motor

Motor type variable speed

Resistance, all 3 windings (25°C) Ω 1.8

Design

Displacement cm

Oil quantity (type) cm

Maximum refrigerant charge g 300

Free gas volume in compressor cm

Weight - Compressor/Electronic unit kg 4.4/0.32

°C 60 (70)

3.00

150 (polyolester)

870

S = Static cooling normally sufﬁ cient O = Oil cooling

= Fan cooling 1.5 m/s

(compressor compartment temperature equal to ambient temperature) F2 = Fan cooling 3.0 m/s necessary SG = Suction gas cooling normally sufﬁ cent – = not applicable in this area

Standard battery protection settings

Voltage 12V 24V

Cut out VDC 10.4 22.8

Cut in VDC 11.7 24.2

Dimensions

Height mm A 137

Suction connector location/I.D. mm | angle C 6.2 | 40°

Process connector location/I.D. mm | angle D 6.2 | 45°

Discharge connector location/I.D. mm | angle E 5.0 | 21°

Connector tolerance I.D. mm ±0.09, on 5.0 +0.12/+0.20

Remarks:

(refer to electronic unit Instructions for optional settings)

B 135

B1 128

B2 73

material | comment Cu-plated steel | Al cap

DEHC.ED.100.G7.02 | 1

Capacity (EN 12900 Household/CECOMAF) 24V DC, static cooling watt

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 35.2 49.8 55.3 67.0 87.3 112 140 3,100 41.9 59.2 65.8 79.8 104 133 168 3,800 50.1 70.8 78.7 95.4 125 159 200 4,400 54.9 78.1 86.8 105 138 176 221

Capacity (ASHRAE LBP) 24V DC, static cooling watt

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 43.7 61.8 68.6 83.1 108 138 174 3,100 52.0 73.4 81.6 98.8 129 165 208 3,800 62.1 87.8 97.5 118 154 197 248 4,400 68.1 96.7 108 130 171 218 274

Power consumption 24V DC, static cooling watt

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 38.4 47.9 51.2 57.8 68.2 79.5 91.9 3,100 46.9 58.9 62.9 70.8 83.4 97.3 113 3,800 57.5 72.0 76.9 86.5 102 119 139 4,400 66.3 83.5 89.2 100 118 138 161

Current consumption

(for 12V applications the following must be doubled) A

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 1.6 2.0 2.1 2.4 2.8 3.3 3.8 3,100 1.9 2.4 2.6 3.0 3.5 4.1 4.7 3,800 2.4 3.0 3.2 3.6 4.3 5.0 5.8 4,400 2.8 3.5 3.7 4.2 4.9 5.8 6.7

COP (EN 12900 Household/CECOMAF) 24V DC, static cooling W/W

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 0.92 1.04 1.08 1.16 1.28 1.40 1.53 3,100 0.89 1.01 1.05 1.13 1.25 1.37 1.48 3,800 0.87 0.98 1.02 1.10 1.22 1.34 1.44 4,400 0.83 0.94 0.97 1.05 1.16 1.27 1.37

COP (ASHRAE LBP) 24V DC, static cooling W/W

rpm \ °C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 2,500 1.14 1.29 1.34 1.44 1.59 1.75 1.90 3,100 1.10 1.25 1.30 1.40 1.55 1.70 1.85 3,800 1.07 1.22 1.27 1.37 1.52 1.66 1.80 4,400 1.02 1.16 1.21 1.30 1.45 1.58 1.71

Test conditions EN 12900/CECOMAF ASHRAE LBP

Condensing temperature 55°C 54.4°C Ambient temperature 32°C 32°C Suction gas temperature 32°C 32°C Liquid temperature no subcooling 32°C

Accessories for BD80F Code number

Bolt joint for one comp. Ø:16 mm 118-1917 Bolt joint in quantities Ø:16 mm 118-1918 Snap-on in quantities Ø:16 mm 118-1919 Remote kit (without cable) 105N9210 One Wire/LIN gateway 105N9501 Automobile fuse, DIN 7258 12V: 30A | 24V: 15 A Main switch

min. 30A

Not deliverable

from Secop

Compressor speed

Electronit unit

Code number

Resistor (R1) [Ω] Motor speed

calculated

values [rpm]

0 AEO

101N0390

with AEO

203 2,500

451 3,100

867 3,800

1700 4,400

In AEO (Adaptive Energy Optimizing) speed mode the BD comressor will always adapt its speed to the actual cooling demand.

Wire dimensions

Size Max. length* Max. length*

Cross AWG 12V operation 24V operation

section

[mm

] [Gauge] [m] [ft.] [m] [ft.]

6 10 2.5 8 5 16

*Length between battery and electronic unit

Operational errors

Error code

or LED

ﬂ ashes

Thermostat failure

(If the NTC thermistor is short-circuit or has no connection).

Thermal cut-out of electronic unit

(If the refrigeration system has been too hea vi ly loaded, or if the ambient tem pe ra ture is high, the electronic unit will run too hot).

Minimum motor speed error

(If the refrigeration system is too heavily loaded, the motor cannot maintain minimum speed at approximately 1,850 rpm).

Motor start error

(The rotor is blocked or the differential pressure in the refrigeration system is too high (>5 bar)).

Too many start attempts or fan over current

(Too many compressor or fan starts in short time or fan current higher than 0.5A

Battery protection cut-out

(The voltage is outside the cut-out setting).

Error type

Can be read out in the software

TOOL4COOL®

avg

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

eady agreed.