Data Sheet
Integrated Presetting Valves, Type RA-N 013G3380
- for Normal Volume Flows
Application
Code Nos. and Technical
Data
Integrated valves type RA-N 013G3380 with builtin presetting are designed for incorporation into
valve radiators from different radiator
manufacturers.
The valve can be recognised by a red presetting
ring.
The valve is to be used in single and two pipe
installations with circulating pump.
The gland seal of the valve can be replaced while
the system is in operation.
Max.
Type
RA-N G ½ A 120 0.05-0.2 0.6 16 10 013G3380
Type
RA-N 0.04 0.09 0.16 0.25 0.36 0.43 0.52 0.73 0.90
Connection
thread
1 2 3 4 5 6 7 N N
water
temp.
°C bar bar bar bar
To avoid calcification and corrosion, it is
important for the composition of the circulating
water to comply with the VDI 2035 guidelines.
Danfoss thermostatic sensors type RA 2000, RASC, RAS-D and RAE with patented snap sockets as
well as Danfoss thermo-hydraulic actuators can
be installed directly onto the integrated valve.
Differential pressure
Rec. Tech
Presetting
kv-value
2) 3)
1)
Test
press.
Work.
press.
Code no.
k
vs
1)
The technical differential pressure indicates the upper limit for a proper valve function. In most two-pipe systems
the recommended differential pressure is sufficient. In order to achieve a noiseless function we recommend in
smaller systems to apply automatic bypass valves or automatic balancing valves. If pump differential pressure
exceeds the recommended max. valve differential pressure it is recommended that an automatic balancing valve
type ASV-P/PV is added to the system.
2)
The kv-values indicate the flow volume (Q) in m³/h at a pressure loss (∆p) across the valve of 1 bar; . At
setting N, the kv-value in accordance with EN 215 can be stated as Xp = 2 K. At lower preset values, Xp will be
reduced until approximately Xp 0.5 at presetting 1. The table shows the average measured values for integrated
valves with radiator. The kvs-values indicate the valve capacity, when the valve is fully open.
3)
When using a liquid filled radiator thermostat e.g. RAS-C, RAS-D, RAE or remote setting element type RA 5060 X
will be increased by factor 1.6 (at setting “N”, ref. EN 215).
Danfoss Heating Solutions VDTVT202 © Danfoss 03/2011 1
p
32 ± 0.5
30.5 ± 0.5
24.5
+0.5
- 0.2
21.5
+0.5
- 0.2
+0.5
- 0.2
13.5
ø11.11 x 1.78
ø18.4 x 2.7
M23.5 x 1.5
ø26.4
max. ø18.7
ø16.7 ±0.1
3
1
2
3
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Spare Parts and Accessories
Design and Dimensions
Product Code no.
Gland seal, 10 pcs.
1)
013G0290
Red protection cap for RA-N valve 013G3380 013G0951
Small O-ring 633B1427
Big O-ring 633B0387
1)
The gland seal of the valve can be replaced under pressure, i.e. while the installation is in operation.
Materials
Part RA-N 013G3380
Valve housing Ms 58
Valve seat Ms 58
Throttle nozzle PPS
Setting dial Plastic
O-rings NBR / EPDM
Valve spindle Ms 58
Valve cone NBR
Pressure pin and valve spring Chrome steel
Presetting
2 VDTVT202 © Danfoss 03/2011 Danfoss Heating Solutions
1. Presetting range
2. Factory setting and one-pipe system
3. Reference mark
The presetting values of the integrated valves
can be adjusted easily and accurately without the
use of tools (factory setting: ‘N’):
Remove the protective cap or the
▪
thermostatic sensor
Find the reference mark
▪
Turn the setting ring until the desired
▪
presetting aligns with the reference mark.
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Capacities without Radiator
and Fittings
The presetting is controlled directly without the
use of equipment. After installation in the
radiator, the reference mark of the valves will not
always be positioned in the same place.
Presetting can be selected infinitely variably
within the range of 1 to 7. At setting ‘N’ the valve
is fully open. Setting in the shaded areas of the
drawing should be avoided.
In a one-pipe installation, the setting ‘N’ must be
used.
RA-N
Setting ‘N’ can be used as a flushing position if
the system has to be flushed out because of dirt
problems.
When the radiator thermostat has been installed,
the presetting is protected against unintended
regulation.
For Danfoss elements RA 2000, RAS-C, RAS-D and
RAE, a theft protection device is available; this
also provides added security against unwanted
adjustment of the preset values.
Capacities at Xp = 2K with Danfoss radiator thermostat RA 2000 are measured without radiator and
connection fittings.
Danfoss Heating Solutions VDTVT202 © Danfoss 03/2011 3
5:1
Min. 40
2 ± 0.3
3.2
ø12 h11
ø10.8 ± 0.2
ø17
R14
R17
ø 0.3 A
5:1
27.5˚ ± 5˚
R 0.3 ± 0.2
0.7 ± 0.2
3.2
45˚ ± 2˚
min. ø 27.5
ø 23.2 ± 0.15
ø 21.1 ± 0.1
G 1/2 ISO 228
min. ø 18.8
A
min. 14
0.2 A
0.1 A
min. 34.5
24 - 30
28 ± 0.5
3.2
± 5°
1
3
4
5
2
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Dimensions
Standard fittings
The dimensions stated may vary according to
different radiator manufacturers.
Mounting Instructions
Installation of an integrated valve at radiator
manufacturer’s plant
An integrated valve can only be fitted once in a
radiator (because of the load on the deformation
zone).
Fit the integrated valve in the radiator using
▪
a 12-edge spanner, KW 21.
Tighten using a torque of 30-35 Nm
▪
If required, continue turning until one of the
▪
cap thread beads points upwards (only
clockwise). Tolerance for adjustment: ±5°.
Removal and fitting in an existing radiator
1. Two O-rings
2. Reference mark
Before removal: Notice the presetting value.
▪
Please mark off the valve position on the
▪
Setting ring with presetting numbers (5):
valve and the radiator (3), e.g. on top (4)
Remove valve.
▪
Fitting: Insert the integrated valve, tighten
▪
until the marked-off position has been
reached.
RA-N types: red plastic
▪
4 VDTVT202 © Danfoss 03/2011 Danfoss Heating Solutions
10 mm
KW 17
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Replacing the Gland Seal
While the system is in operation, the gland seal can be replaced by means of a spanner, KW 10. Hold
the setting ring using a 12-edge ring-spanner, KW 17.
Firmly
Danfoss Heating Solutions VDTVT202 © Danfoss 03/2011 5
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
6 VDTVT202 © Danfoss 03/2011 Danfoss Heating Solutions
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Danfoss Heating Solutions VDTVT202 © Danfoss 03/2011 7
Data Sheet Integrated Presetting Valves, Type RA-N 013G3380 - for Normal Volume Flows
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone:+45 7488 8000
Fax: +45 7488 8100
Email: heating.solutions@danfoss.com
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
8 VDTVT202 © Danfoss 03/2011 Danfoss Heating Solutions
Loading...