Data Sheet
PLUS+1® Expansion Module
IOX018-130 High Current
Mobile machine management
IOX018-130 High Current Expansion Module is an
element of the flexible, powerful and expandable
PLUS+1® family of mobile machine management
products. Expansion modules provide cost-effective
additional I/O to mobile machine control systems.
Product highlights
The PLUS+1® High Current expansion module
employs a 32 bit Cortex-M3 Processor, providing the
controller with extremely fast single cycle processing
speed. It features high current capabilities for your
machine control.
PLUS+1® compliance eliminates need for the system
designer to write CAN transmit and receive messages
in both the controller and associated expansion
modules.
Application development
Users configure expansion modules using PLUS+1
GUIDE. This Microsoft® Windows®-based
development environment features a user-friendly,
field proven, icon-based graphical programming tool,
application downloader, and service/ diagnostic tool.
Features
•
User-programmable with PLUS+1
GUIDE (Graphical User Integrated
Development Environment)
•
18 pins: (2) DEUTSCH connectors (DT
and DTP), (2) 6 mm studs
•
12 bit analog-to-digital converter
•
ARM 32 bit Cortex-M3 running at 120
MHz
®
®
Comprehensive technical literature is
online at www.danfoss.com
©
Danfoss | March 2019 AI297367135765en-000102 | 1
Data Sheet
IOX018-130 High Current Expansion Module
4 inputs
•
(2) Universal (DIN/AIN/FreqIN/Rheo)
Digital: Pull up (5 VDC), pull down (0
VDC) or pull to center (2.5 VDC)
Analog: 0 to 0.375 VDC, 0 to 5.25 VDC, or
0 to 36 VDC
Frequency (timing): 1 Hz to 10 kHz
Resistance: 0 to 10,000 ohm
•
(1) Digital/Analog (DIN/AIN) that is userdefined as either:
Digital: Pull up (5 VDC), pull down (0
VDC) or pull to center (2.5 VDC)
Analog: 0 to 5.25 VDC or 0 to 36 VDC
•
(1) Digital/Analog/CAN shield
(DIN/AIN/CAN shield) that is userdefined as either:
Digital: Pull up (5 VDC), pull down (0
VDC) or pull to center (2.5 VDC)
Analog: 0 to 5.25 VDC or 0 to 36 VDC
CAN shield
Characteristics
Supply voltage 9 to 36 VDC
Operating temperature (ambient) – 40°C to 70°C [– 40°F to 158°F]
Storage temperature – 40°C to 85°C [– 40°F to 185°F]
Programming temperature – 40°C to 70°C [– 40°F to 158°F]
IP rating (with mating connector attached) IP 67
EMI/RFI rating 100 V/M
Weight 1.29 kg [2.85 lb]
Vibration IEC 60068-2-64
Shock IEC 60068-2-27 test Ea
Maximum current, sourcing 120 A
Maximum current, sinking 120 A
8 outputs
•
•
(4) Universal (PWMOUT/DOUT/PVGOUT)
that are user-defined as either:
Digital: 15 A, configurable as source or
sink
PWM: 15 A (33 to 4000 Hz or 20 kHz),
configurable as open or closed loop
with current control
(4) Universal (PWMOUT/DOUT/PVGOUT)
that are user-defined as either:
Digital: 25 A, configurable as source or
sink
PWM: 25 A (33 to 4000 Hz or 20 kHz),
configurable as open or closed loop
with current control
2 | © Danfoss | March 2019 AI297367135765en-000102
M6 locknut
Install torque 7.344 N•m
2X 10 M6
Threaded stud
Red LED
Green LED
80.2
11.7
12.3
173
2X 151
4X Ø 6.75
2X 167
189
ohj1479876644922
C3
C4
nmp1479876497075
cvi1479876589499
Data Sheet
IOX018-130 High Current Expansion Module
Dimensions and pin assignments
Dimensions in millimeters
C1
DEUTSCH DT Series 12 pin
Pin Controller function Pin Controller function
1 Logic ground 7 DIN/AIN/FreqIN/Rheo
2 Logic power 8 DIN/AIN/FreqIN/Rheo
3 CAN_HI 9 15A PWM
4 CAN_LO 10 15A PWM
5 DIN/AIN1/CAN shield 11 15A PWM
6 DIN/AIN2 12 15A PWM
C2
DEUTSCH DTP Series 4 pin
Device must be mounted on a flat metal surface that is less than
70° C (158° F) for full output capability.
If the metal surface is greater than 70° C (158° F), built in thermal
protection will limit the maximum output current allowed for all
PWM’s.
Use care when wiring mating connector. Pinouts are for device
pins.
Pin Controller function
1 25A PWM
2 25A PWM
3 25A PWM
4 25A PWM
C3, C4
Pin Controller function Description
C3-P1 Battery power
C4-P1 Battery ground 120A battery connection
120A battery connection
(externally fused)
©
Danfoss | March 2019 AI297367135765en-000102 | 3
Ordering information
Product part number
IOX018-130 11227542
Related products part numbers
CG150-2 CAN/USB Gateway 11153051
PLUS+1® GUIDE Professional 11179523
Danfoss mating connectors bag assemblies and fuse part numbers
4 pin DEUTSCH mating connector bag assembly
(10 to 14 AWG)
12 pin DEUTSCH mating connector bag assembly
(14 to 20 AWG)
4 and 12 pin DEUTSCH mating connector bag assembly 11188232
125 Amp fuse 11188233
11188220
11188221
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
4 | © Danfoss | March 2019 AI297367135765en-000102
Loading...