Danfoss Icon Programmable User guide

User Guide

Danfoss Icon™ Programmable

Room Thermostat, 230 V

Introduction

Know your
Danfoss Icon™
Programmable

Danfoss Icon™ Programmable is a room thermostat especially designed for floor heating systems.

Danfoss Icon™ Programmable is very easy to use:

• Seven pre-defined and fixed heating programs makes it easy to find a schedule that suits your
personal needs.

• An easy-to-use interface with icons for different modes makes it simple to override a program with­out changing the program settings.

Wake up the thermostat

Danfoss Icon™ Programmable is designed to blend in with any interior.
When not in use, the display turns off and becomes virtually invisible.

When the screen is touched, the display comes to life instantly and
displays the current room temperature for two seconds, then switches
to Home Screen.

The Heating icon is displayed, if the thermostat has turned on the
heat.

The Cooling icon is displayed, if the thermostat has turned on the
cooling (only if cooling is enabled in your system).

The Home Screen

On the Home Screen the icon for active mode is fully lit,

e.g. At Home .

Icons for inactive modes are dimmed down, but still visible..

Activate another mode by touching the icon.

If no icon is touched, the screen will go to sleep after ten seconds.

Home Screen icons

At Home: Touch icon to set temperature for the At Home period (your comfort temperature).

Away: Touch icon to set temperature for the Away period (your economy temperature).

Asleep: Touch icon to set temperature for the Asleep period (your comfort temperature at

night).

Settings: Touch icon to choose program and change settings.

Return to the previous screen/setting.

VUMBA102

© Danfoss | FHH | 2016.08 | 1

User Guide Danfoss Icon™ Programmable Room Sensor 230 V

How to use
Danfoss Icon™
Programmable

Danfoss Icon™ Programmable is easy and intuitive to use:

• You change value with or .

• You scroll between menus and programs with or .

• You confirm with . The screen is flashing shortly to indicate that the new setting is active.

Forecast feature

Danfoss Icon™ Programmable has an automatic Forecast feature, where the thermostat during the first
two weeks adapts itself to the characteristics of the room.

It means that Danfoss Icon™ Programmable learns when to start heating up in order to reach the
desired At Home temperature on time (re-heating times can be very different from room to room).

This is especially important with underfloor heating in heavy floor constructions, because the floor
concrete need to be heated, and it takes time.

Example:

Program P4 is chosen.

Away temperature from 09:00 is set to 18° C.
At Home temperature from 17:00 is set to 21° C .

21°

Recommendations
on set-back
temperatures

18°

Forecast says: Start heating now!

The Forecast feature has learned that heating must start up at 15:20 in order to reach the At Home
temperature of 21° C at 17:00.

For a traditional heavy floor heating system with pipes embedded in concrete, Danfoss recommends
Away and Asleep (set-back) temperatures a few degrees lower than the At Home (comfort) tempera-
ture. A larger temperature difference will be “overruled” by the Forecast feature.

With a light (dry) floor construction cooling / heating time is shorter, and you might choose a larger
temperature difference.

17:0009:00

15:20

2 | © Danfoss | FHH | 2016.08

Heavy floor heating construction

Light floor heating construction

VUMBA102

User Guide Danfoss Icon™ Programmable Room Sensor 230 V

How to use
the modes

At Home mode

Touch to activate the At Home mode.

Touch again to show the desired At Home temperature.

Default temperature is 21° C.

Change the desired temperature by touching or .

Confirm your settings by touching .

Away mode

Touch to activate the Away mode.

Touch again to show the desired Away temperature.

Default temperature is 17° C.

Change the desired temperature by touching or .

Confirm your settings by touching .

Asleep mode

Touch to activate the Asleep mode.

Touch again to show the desired Asleep temperature.

Default temperature is 19° C.

Change the desired temperature by touching or .

Confirm your settings by touching .

Reset to default
factory settings

VUMBA102

Settings mode

Touch to open the Settings menu.

Toggle between Settings menus by touching or .

Confirm your choice by touching .

Note! Settings are usually made by the installer, and you will normally not
have any need for changing the settings.

Press and simultaneously for at least 3 seconds to reset Danfoss I con™ Programmable to the
default factory settings.

The display toggles between and .

Confirm by touching .

© Danfoss | FHH | 2016.08 | 3

User Guide Danfoss Icon™ Programmable Room Sensor 230 V

User menus

Choose program

Select between the weekly programs to with or .

Confirm your choice with .

Note! See overview of pre-defined and fixed heating programs on page 5 & 6.

Temperature limitation

Limitation of the temperature range between 5 and 35° C.

Set highest and lowest temperature with or .

Confirm each setting with .

Setting time and date

Set the clock (for correct function of Daylight Saving Time and the weekly programs).

Set Year , Month , Day , Hour and Minute with or .

Confirm each setting with .

Daylight Saving time

Choose between Automatic Shift or Shift Off with or .

Confirm your choice with .

Software version

Identification of the software version in the Danfoss Icon™ Programmable thermostat.

Menu 6 to 9 are only relevant for the installer (access by pressing for at least 3 seconds)

Set actuator type

Choose between Normally Closed or Normally Open with or .

Confirm with .

Set heat emission characteristics of the floor

4 | © Danfoss | FHH | 2016.08

Choose Fast , Medium or Slow heat emission characteristics with or .

Confirm with .

VUMBA102

User Guide Danfoss Icon™ Programmable Room Sensor 230 V

User menus
with floor sensor

Menu 8 and 9 are only visible on the display, if a floor sensor is connected.

Temperature control with Floor sensor

Choose between temperature control with only Floor sensor or a Combination of Floor and
Internal sensor with or .

Confirm with .

: Controls the temperature based on air temperature in the room, but within the floor tem-

perature range set in Menu 9.

: Controls the temperature based on a fixed floor temperature, which is set for each of the

modes At Home , Away and Asleep .

Menu 9 is only visible on the display, if is chosen in Menu 8.

Limitation of the floor temperature

Set highest and lowest floor temperature between 18 and 45° C with or .

Confirm each setting with .

How to choose
a Program

Program overview

Touch to open the Settings menu. is displayed.

is the Programs menu. Open the menu by touching .

Toggle between the programs with or .

Confirm your choice with .

Note! Desired temperatures are set by accessing each of the three modes via the Home Screen.

At Home Away Asleep

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Default program. No automatic schedule, last chosen temperature remains active until settings are
changed manually.

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Example: Residents At Home during the day, with Asleep temperature set-back in the night.

VUMBA102

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Example: Residents Away from 8 to 15, with Asleep temperature set-back in the night.

. . . more programs

© Danfoss | FHH | 2016.08 | 5

Program overview

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Example: Residents Away from 8 to 16, with Asleep temperature set-back in the night.

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Example: Residents Away from 9 to 17, with Asleep temperature set-back in the night.

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Thu

Fri

Sa-Sun

Example: Program for weekend cottages. Residents Away Monday to Friday afternoon and At Home

during the week-end.

0 2 4 6 8 10 12 14 16 18 20 22 24

Mon-Fri

Sa-Sun

Example: Program for shops and offices.

Alarm

Overriding a program

You can temporarily override a program by touching an icon on the Home Screen. The new tempera­ture will be active until next scheduled program change.

Example: You come home during an Away period and touch the At Home icon to raise the room tempera­ture to the At Home level.

If a connected floor sensor becomes defective, an alarm is indicated by flashing on the display for 1
second every 20 seconds.

Touch the screen and the display toggles between and .

Confirm with .

Normal operation (setting of temperature, etc.) is now possible with the room sensor only. The alarm is
still on, indicated by flashing.

Contact your installer and let him cancel the alarm by:

1. Re-connecting the floor sensor. If the flashing disappears the error is corrected.

2. Exchange the floor sensor. If the flashing disappears the error is corrected.

3. Disconnect the floor sensor and reset Danfoss I con™ Programmable to default factory settings.
The alarm is now off, but the thermostat works without floor sensor.

Danfoss A/S

Danfoss A/S

Floor Heating Hydronics • Ulvehavevej 61 • DK-7100 Vejle • Denmark • Phone: [phone] • Fax: [phone]

Floor Heating Hydronics • Ulvehavevej 61 • DK-7100 Vejle • Denmark • Phone: [phone] • Fax: [phone]

[e-mail] • www.floorheating.danfoss.com

[e-mail] • www.floorheating.danfoss.com

Danfoss ca n accept no respons ibility for pos sible errors in ca talogues, bro chures and other pr inted material. Da nfoss reserve s the right to alter its p roducts with out notice. This als o applies to produ cts

Danfoss ca n accept no respons ibility for pos sible errors in ca talogues, bro chures and other pr inted material. Da nfoss reserve s the right to alter its p roducts with out notice. This als o applies to produ cts

already o n order provided t hat such alteratio ns can be made with out subsequenti al changes being n ecessary in sp ecifications alr eady agreed.

already o n order provided t hat such alteratio ns can be made with out subsequenti al changes being n ecessary in sp ecifications alr eady agreed.

All trade marks in this mate rial are proper ty of the respec tive companies . Danfoss and the Danf oss logotyp e are trademark s of Danfoss A/S. Al l rights reserv ed.

All trade marks in this mate rial are proper ty of the respec tive companies . Danfoss and the Danf oss logotyp e are trademark s of Danfoss A/S. Al l rights reserv ed.

6 | © Danfoss | FHH | 2016.08

VUMBA102