Danfoss ICAD 600, ICAD 900 Installation guide
Installation Guide
Heat Cartridge Kit
ICAD 600 / ICAD 900 for ICM
Technical data
Danfoss recommends the installation of the Heat Cartridge
027R9788
Kit ICAD 600 / ICAD 900 on ICM motor operated valves in
the following applications:
When the media temperature through the ICM valve is lower
than –30oC (–22oF).
When the ICM valve is installed outdoor and the media
temperature through the ICM valve is lower than –10oC (14oF).
When the ICM is installed indoor, with relative humidity higher
than 90%, and when the media temperature though the ICM
valve is lower than –10oC (14oF).
2.5 mm Hexagon key
Heat cartridge holder
Heat conduction compound
Voltage
24 V d.c / 24 V a.c
Load
1.5 A / 30 W
Cable
The Heat Cartridge is delivered with 1 m (39 in.) cable.
3 × 0.5 mm2 (3 × ∼ 20 AWG).
• Brown and Blue: 24 V d.c (polarity unimportant), 24 V a.c
• Yellow/Green: Ground/Earth
1C
1B
027R9788
1A
2.5 mm Hexagon key
Heat cartridge
ICAD
Code numbers
Heat Cartridge Kit ICAD 600 for
ICM 20
ICM 25
ICM 32
Heat Cartridge Kit ICAD 900 for
ICM 40
ICM 50
1
ICM 65
027H1200
027H1205
027H1210
027H1201
027H1206
027H1211
Heat Cartridge Kit
Code number
027H1209
027H1219
The Heat Cartidge Kit contains:
• Heat cartidge
• Heat cartidge holder
• Heat conduction compound
© Danfoss A/S (MWA), 2015-01 DKRCI.PI.HT0.E4.02 / 520H2195 1
ICAD
2.5 mm Hexagon key
2 3
Installation
Mechanical installation
General procedure for installing the Heat Cartridge Kit ICAD 600 /
ICAD 900 on all sizes of ICM valves:
Please Note:
The Heat Cartridge Kit ICAD 600 / ICAD 900 must be installed
before the ICAD 600/900 actuator is mounted on the ICM valve.
• Check that the three socket set screws on the ICAD actuator are
counter clockwise fully unscrewed and removed with a 2.5 mm
Hexagon key (see g. 2).
• Check that the two socket set screws on the heat cartridge
holder are counter clockwise fully unscrewed with a 2.5 mm
Hexagon key (see g. 1).
• Apply heat conductive compound to:
• the heat cartridge (marked 1A in g. 1)
• into both ends of the holes for heat cartridge,
on the heat cartridge holder (marked 1B in g. 1)
• on the inner surface of the heat cartridge holder (marked 1C
in g. 1)
2 DKRCI.PI.HT0.E4.02 / 520H2195 © Danfoss A/S (MWA), 2015-01
• Insert the heat cartridge into the smallest hole of the heat
cartridge holder (see g. 1).
• Fasten the heat cartridge with the socket set screw using a
2.5 mm Hexagon key.
• Insert the ICAD into the hole of the heat cartridge holder. (g. 2)
• Install the heat cartridge holder on the ICAD actuator. Position
the heat cartridge holder in a center position as shown in g. 3
• Fasten the heat cartridge holder using a 2.5 mm Hexagon key.
• Reinstall the three socket set screws on the ICAD actuator.
• Please consult the ICAD instruction (DKRCI.PI.HV0.A) regarding
the mounting of ICAD actuators on ICM motor operated valves.
Electrical installation
Please Note:
Do not connect supply voltage before the heat cartridge is
inserted into the hole of the the heat cartridge holder - then
connect 24 V d.c/a.c
Loading...