Danfoss DST P1XX Installation guide [da]
Installation guide
Pressure transmitters
DST P1XX
Electrical connection: See product label
Electrisk tilslutning: Se produktskilt
075R0 013
Elektrischer Anschluss: Siehe Produktschild
Raccordement électrique: Voir étiquette du produit
Conexión eléctrica: Ver la pegatina en el producto
Connessione elettrica: Vedi etichetta sulla confezione
Electrical
connector has
to be mounted
on the Pressure
Transmitter
before pressure
is added on the
application
M12 x 1, 4 pin
Danfoss
64G101
Elektrisk
tilslutning skal
tilsluttes
tryktransmitteren
før der kommer
tryk på
applikationen
(1)
4 pole
ISO 15170,
(2)
Bayonet
Der elektrische
Anschlussstecker muss am
Drucktransmitter
montiert werden,
bevor Druck
auf die Anlage
gegeben wird
Metri-Pack 150
Le transmetteur
de pression doit
être raccordé
électriquement
avant que
l’application
ne soit sous
pression
El conector
eléctrico
tieneque estar
montado en el
transmisor de
presión antes
de que se añada
presión en la
aplicación
AMPseal 16 Deutsch DT04, 4pin
Danfoss
64G102
Il connettore
elettrico deve
essere montato
sul Trasmettitore
di pressione
prima che venga
applicata
pressione sul
sistema
075R0 013
DST P1XX
(1)
Tightening torque between electrical connector and mating connector (e.g. adaptor, cable, etc) is limited.
Recommended is 0,5Nm and the maximum is 1,2Nm.
(2)
Maximum tightening torque is 1,2Nm as per the ISO standard.
American and Canadian approvals:
Must be powered by Class 2 power supply
1. Automatic electrical controls acc. to UL 60730-1 and part 2-6 /CAN/CSA E60730 and
part 2-6, file E31024.
2. Equipment for process measurement and control acc. to UL 61010-1 / CSA C22.2 No.
61010-1-12, file E494625.
3. Nonincendive electrical equipment for use in Class I, Div. 2, Groups A, B, C & D
harzarous locations in acc. to UL 121201 / C22.2 No. CSA-213, file E510763.
4. The MWP 50 bar (max. working pressure))’
5. Evaluated for pollution Degree 2
6. Altitude up to 8000 m
7. Max. R.H. 95% non-condensing
8. Overvoltage category I
© Danfoss | Climate Solutions | 2021.03 AN31455060087901-000602 | 1
Type DST P1XX Current output Absolute voltage output Ratiometric output
Max. ambient temperature
Temperature code T4 T4 T4
Voltage Supply
Output 4 - 20 mA 0 - 10 V 10 - 90% Vss
SAE Female Flare
1/4” Solder connection
85 °C / 212 °F 125 °C / 257 °F 125 °C / 257 °F
+ 8 to 28 V DC + 8 to 32 V DC + 5V DC ± 10%
SAE Female Flare
• Suitable for use with Schrader Valve connections
• Recommended installation torque: 17Nm (12.5 ft-lb)
(1)
Only for reference. Mating materials and thread sealants might
(1)
require different torque values among applications.
Max. 125 °C
(275 °F)
• Under these conditions no additional cooling of the sensor is required
• Nitrogen shielding optional
© Danfoss | Climate Solutions | 2021.03
Max. 850°C
(1550 °F)
AN31455060087901-000602 | 2
Loading...