Danfoss DEVIheat Sport 90S Data sheet
1. Embedded systems
DEVImat™ DSVF-90
Data Sheet
DTCE
DEVIheat™ Sport 90S
DEVIheat™ Sport 90S is a single conductor heating mat for installation under artificial grass.
It is specially designed and configured for installation under artificial grass fields with the
purpose of establishing frost protection. Though it is small, the sturdy heating element
resists the continuous stress from players and vehicles.
DEVIheat™ Sport 90S is tested for artificial grass with topdressing ”Infillpro Geo” from
Limonta Sport, Italy. If any other artificial grass type/producer is expected, please contact
DEVI/Danfoss for testing underlay and top layer, including the specified top dressing,
before the solution could be accepted.
Benefits:
• Thin, only 3 mm including mesh
• Protective mesh
• Sturdy heating element
• Ø10 mm connection
• Other mat sizes on request
Standard compliance:
• EN 60335-1
• EN 60335-2-96
• EN 50581
Approvals:
Types
Type
Nominal voltage 230 V~
Output 90 W/m² @ 230 V~ (3245 W )
Mat size
Construction
Cable diameter 2,5 mm
Cold tail 2 x 24 m, DSWA, 2,5 mm² with screen
Deformation strength, min. 600 N
Pulling strength, min. 120 N
Conductor insulation FEP
Outer sheath PVDF
Screen 10 x 0,25 mm Cu threads
Min. installation temperature -5 °C
Max. permissible use temperature, powered 70 °C
Min. bending Ø 6 x cable diameter
IP Class IPX7
Value
70,5 x 0,5 m;
Other mat length ±3 m on request
Single conductor, round with screen,
two cold leads
Item no. Heated area Dimensions (W x L) Output @ 230V~ Resistance Cold lead EAN no.
140F0399 35,25 m² 0,5 x 70,5 m 3245 W 16,3 Ω 1 x 2,5 mm² 5703466217344
Accessories
Item no. Description EAN no.
19805907 Synthetic nail, 40 pcs. in box 5703466249536
Produced by Danfoss ©AI319535865523en -010104
Installation Step-by-step
1. Roll out and find the centre of the mat. 2. At the centre of the mat, cut the mesh - not the
cable.
3. Secure the heating mat at the centre of the field,
using the special carbon nails. Roll and stretch the
mat towards the sideline.
5. Remember to mark goal posts, corner flags, etc.
to secure that the heating mat / cables are not damaged when making the holes for the posts.
Installation
During installation of the heating mats an expert installation
engineer must be present to supervise the installation and perform
the required tests.
• Install the heating mat on top of the shock pad - mesh up.
• When rolling out the heating mat, secure the cold lead inside
the cardboard tube of the roll in order for the cold lead not to be
twisted.
• Mind that the cable does not drop down into the grooves in the
shock pad.
4. When reaching the side line secure the heating
mat with the special carbon nails, one every 30 cm.
6. Cut a groove into the shock pad - not the draining
mat, embed the cold leads and take them to the
nearest cable vault.
• Do not step on the heating mats during installation.
• Use a rubber-headed hammer to secure the special carbon nails
to the heating mat.
• Do not allow the heating mat to shift when laying out the
artificial grass rolls.
• Do not use tools with sharp edges, do not use footwear with rough
soles or similar, as this, in many cases, may damage the electrical
heating mats.
• Only use the artificial grass for playing football.
Produced by Danfoss ©AI319535865523en -010104
Loading...