Description
The current sensor cylinder busbar kits include all parts
required to install the cylinder busbars in D1h–D8h drives.
Each cylinder busbar is inserted through the center of a
current sensor during installation. For more information, see
the current sensor kit installation instructions listed in
Tab l e 1.4 .
Kit Ordering Numbers
Kit number Kit description
176F6517 300 A D1 LEM BB kit
176F6757 300 A D2 LEM BB kit
176F6756 500 A D2 LEM BB kit
Table 1.1 Ordering Numbers for Current Sensor Cylinder Busbar Kits
Items Supplied
Item Quantity
Nomex sleeve 3
U, V, W cylinder busbars 1 set of 3
M6x90 screw 3
Cylinder busbar mounting frame 1
M6x16 screw 3
Table 1.2 Items Supplied with D1h/D3h/D5h/D6h Kit (176F6517)
Item Quantity
Nomex sleeve 3
U, V, W cyclinder busbars 1 set of 3
M8x70 screw 3
Table 1.3 Items Supplied with D2h/D4h/D7h/D8h Kit
(176F6756/176F6757)
Safety Information
Only qualied, Danfoss authorized personnel are allowed to
install the parts described in these installation instructions.
Handling of the drive and its parts must be done in
accordance with the corresponding operating guide.
WARNING
ELECTRICAL SHOCK HAZARD
VLT® FC series drives contain dangerous voltages when
connected to mains voltage. Improper installation, and
installing or servicing with power connected, can cause
death, serious injury, or equipment failure.
To avoid death, serious injury, or equipment failure:
•
Only use
qualied
electricians for the installation.
•
Disconnect the drive from all power sources before
installation or service.
•
Treat the drive as live whenever the mains voltage
is connected.
•
Follow the guidelines in these instructions and local
electrical safety codes.
WARNING
DISCHARGE TIME
The drive contains DC-link capacitors, which can remain
charged even when the drive is not powered. High voltage
can be present even when the warning LED indicator lights
are o. Failure to wait the specied time after power has
been removed before performing service or repair work can
result in death or serious injury.
•
Stop the motor.
•
Disconnect AC mains and remote DC-link power
supplies, including battery back-ups, UPS, and DClink connections to other drives.
•
Disconnect or lock PM motor.
•
Wait for the capacitors to discharge fully. The
minimum waiting time is 20 minutes.
•
Before performing any service or repair work, use
an appropriate voltage measuring device to make
sure that the capacitors are fully discharged.
Installation Instructions
Current Sensor Cylinder Busbar Kit (D1h–D8h)
VLT
®
FC Series FC 102, FC 103, FC 202, FC 302
Danfoss A/S © 08/2018 All rights reserved. MI70Z202
Cylinder Busbar
Identication
Kit 176F6517 Kit 176F6757 Kit 176F6756
90/110/132 kW power rating 160 kW power rating 200/250 kW power rating
V-phase busbar: 64 mm x
Ø
16 mm
U/W-phase busbar: 71 mm x
Ø
16 mm
U/V/W-phase busbar:
49 mm x
Ø
19 mm
U/V/W-phase busbar:
49 mm x Ø25 mm
Illustration 1.1 Current Sensor Cylinder Busbars
Busbar kit Current sensor kit Kit description Installation instruction
176F6517 176F6516 300 A D1 retro t kit 300 A Current Sensor Kit for D1h/D3h/D5h/D6h Drives
176F6757 176F3752 300 A D2 retro t kit 300 A/500 A Current Sensor Kit for D2h/D4h/D7h/D8h Drives
176F6756 176F3737 500 A D2 retro t kit 300 A/500 A Current Sensor Kit for D2h/D4h/D7h/D8h Drives
Table 1.4 Comparison of Current Sensor Cylinder Busbar Kits
Installation Instructions
Current Sensor Cylinder Busbar Kit (D1h–D8h)
VLT
®
FC Series FC 102, FC 103, FC 202, FC 302
2
Danfoss A/S © 08/2018 All rights reserved. MI70Z202
Assembling the Current Sensor Cylinder Busbars in D1h/D3h/D5h/D6h Drives
WARNING
NOMEX SLEEVES REQUIRED
The Nomex sleeves are required to maintain proper electrical protection. Failure to install the Nomex sleeves can result in
personal injury or equipment damage.
•
Do not discard the Nomex sleeves.
Use the following steps to assemble the current sensor cylinder busbars in D1h/D3h/D5h/D6h drives. Refer to Illustration 1.2.
1. Place the 3 Nomex sleeves over the cylinder busbars,
1 per busbar. Place the sleeve with the red marking
on the short busbar.
2. Insert 3 M6x90 screws through the center of the
busbars and place the busbar mounting frame, 1
screw per busbar. The busbar with the red marking is
the V busbar and is mounted in the middle.
3. Retain 3 M6x16 screws to fasten the busbar
mounting frame in the drive when installing the
current sensors. The cylinder busbars are inserted
through the centers of the current sensors. Refer to
300 A Current Sensor Kit for D1h/D3h/D5h/D6h Drives
installation instruction.
1 Cylinder busbar mounting frame 4 M6x90 screw
2 Nomex tube 5 Cylinder busbars (assembled)
3 Cylinder busbar 6 M6x16 screw
Illustration 1.2 Current Sensor Cylinder Busbar Assembly in D1h/D3h/D5h/D6h Drives
Installation Instructions
Current Sensor Cylinder Busbar Kit (D1h–D8h)
VLT
®
FC Series FC 102, FC 103, FC 202, FC 302
MI70Z202 Danfoss A/S © 08/2018 All rights reser ved.
3
Assembling the Current Sensor Cylinder Busbars in D2h/D4h/D7h/D8h Drives
WARNING
NOMEX SLEEVES REQUIRED
The Nomex sleeves are required to maintain proper electrical protection. Failure to install the Nomex sleeves can result in
personal injury or equipment damage.
•
Do not discard the Nomex sleeves.
Use the following steps to assemble the current sensor cylinder busbars in D2h/D4h/D7h/D8h drives.
1. Place the 3 Nomex sleeves over the cylinder busbars,
1 per busbar.
2. Insert 3 M8x70 screws through the center of the
busbars, 1 screw per busbar.
3. The cylinder busbars are inserted through the centers
of the current sensors when installing the current
sensors in the drive. See 300 A/500 A Current Sensor
Kit for D2h/D4h/D7h/D8h Drives installation
instruction.
1Nomex sleeve
2Cylinder busbar
3M8x70 screw
Illustration 1.3 Current Sensor Cylinder Busbar Assembly in
D2h/D4h/D7h/D8h Drives
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this materi al are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com
*MI70Z202*
MI70Z202130R0842 08/2018
Loading...