Danfoss 176F6489 Installation Instructions Manual

Description

The bus bar kit is designed for the specic VLT® HVAC Drive FC

102, VLT

®

AQUA Drive FC 202, and VLT® AutomationDrive FC

302 D4h-size VLT

®

Parallel Drive Modules mounted in a Rittal
TS8 enclosure. The bus bars in this kit link 2 drive modules in
parallel.

Kit Part Number

Part number Kit description

176F6489

Bus bar kit for the VLT

®

Parallel Drive Modules

(12-pulse, 2-drive system)

Table 1.1 Part Number for the VLT® Parallel Drive Modules

Bus Bar Kit

Items Supplied

The kit contains the following parts:

Bus bar assembly

•

Nut with integrated washer, M5 (10)

•

Nut with integrated washer, M8 (10)

•

Nut with integrated washer, M10 (6)

•

Screw, M5 x 12 mm (40)

•

Screw with integrated washer, M10 x 30 (6)

•

Stand-o, M5 x 25 (15)

•

Ground bus bar, 800 mm (1)

•

Ground plate (1)

•

Ground jumper plate (2)

•

Ground jumper bus bar (2)

•

Ground clamp (1)

•

EMI/EMC bracket, left (2)

•

EMI/EMC bracket, right (2)

•

EMI/EMC bracket, front (2)

•

EMI/EMC shield, lower (1)

DC bus assembly

•

L-brackets (2)

•

DC-link jumper bus bar (-) (2)

•

Jumper bus bar (+) (2)

•

DC bus support plate (1)

•

DC-link bus bar (2)

AC bus bar assembly

•

Brake terminal, left (2)

•

Brake terminal, right (2)

•

Brake terminal bracket (2)

•

Solid AC bus bar, (6)

•

AC bus bar assembly bracket (1)

•

S-bracket (1)

•

Flexible AC bus bars (6)

•

AC support bracket (1)

•

Side support (2)

Safety

WARNING

DISCHARGE TIME

The frequency converter contains DC-link capacitors, which
can remain charged even when the unit is o. High voltage
can be present even when the warning indicator lights are
o. Failure to wait 20 minutes after power has been
removed before performing service or repair work, could
result in death or serious injury.

•

Stop the motor.

•

Disconnect the AC mains, permanent magnet type
motors, and remote DC-link supplies, including
battery back-ups, UPS, and DC-link connections to
other frequency converters.

•

Wait 20 minutes for the capacitors to discharge fully,
before performing any service or repair work.

•

Measure the voltage level to verify full discharge.

Installation

NOTICE

If both a bus bar kit and a back-channel cooling kit are
being installed in the cabinet, install the back-channel
cooling kit rst.

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

Danfoss A/S © 04/2016 All rights reserved. MI92O102

NOTICE

APPROVALS AND CERTIFICATIONS

This VLT® Parallel Drive Modules bus bar kit is UL 508C
compliant. These installation instructions describe how to
install Danfoss-supplied bus bars which, if followed, meet
specic agency approvals and certications. Seek agency
approvals or

certications

apart from Danfoss if designing

and building other congurations.

Installing DC-link Bus Bars

1. Install 1 L-bracket inside the top of the enclosure on
each side. Secure each bracket with 3 M5 nuts and
torque to 2.3 N · m (20 in-lb). See Illustration 1.1.

1 L-brackets 2 DC fuse with microswitch

Illustration 1.1 Installation of DC Bus Bar L-brackets above the

DC Fuses

2. Install the 6 stand-os onto the support plate. Torque
to 2.3 N · m (20 in-lb). Refer to Illustration 1.2.

3. Install the 2 DC-link bus bars onto the support plate
using 3 M5 nuts per bus bar. Torque to 2.3 N · m
(20 in-lb).

1 Support plate 3 DC-link bus bars

2 Stand-os 4 M5 nut

Illustration 1.2 Installing DC-link Bus Bars onto Support Plate

4. With the DC-link bus bars facing downward, slide the
support plate onto the L-brackets. Secure the support
plate with 6 M5 screws and torque to 2.3 N · m
(20 in-lb). Refer to Illustration 1.3.

5. Install the DC+ and DC- jumper bus bars between
the DC fuses and the DC bus bars. Refer to
Illustration 1.4.

1L-brackets

2 DC-link bus bar assembly (support plate and bus bars)

Illustration 1.3 Installation of DC Bus Bars onto L-brackets

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

2

Danfoss A/S © 04/2016 All rights reserved. MI92O102

1 DC-link jumper bus bars (+/- indicated in drawing) 3 Microswitch

2 DC-link bus bar 4 DC fuse

Illustration 1.4 Installation of DC Jumper Bus Bars

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

MI92O102 Danfoss A/S © 04/2016 All rights reserved.

3

Assembling the AC Bus Bar Subassemblies

The AC bus bar assembly consists of the following 3 subassemblies, as shown in Illustration 1.5.

1 AC bus bar assembly bracket 3 AC support bracket with drive module 2 brake terminal assembly

2 Motor bus bar subassembly – –

Illustration 1.5 Exploded View of the AC Bus Bar Assembly

1. Install the left and right brake terminals onto the brake terminal bracket using 4 M5 nuts. Torque to 2.3 Nm (20 in-lb).

2. Secure the brake terminal assembly to the AC bus bar assembly bracket with 2 M8 nuts. Torque to 9.6 Nm (85 in-lb).
Refer to Illustration 1.6.

3. Install the S-bracket to the AC bus bar assembly bracket using 2 M5 nuts. Torque to 2.3 Nm
(20 in-lb).

1 AC bus bar assembly support bracket 4 M5 nut

2 Mounting point for lower EMI/EMC shield 5 S-bracket

3 Brake terminal assembly (terminals and bracket) 6 Studs that insert into the side support bracket

Illustration 1.6 Assembling the AC Bus Bar Assembly Bracket

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

4

Danfoss A/S © 04/2016 All rights reserved. MI92O102

4. Assemble the motor bus bar subassembly using 9 stand-os and 9 M5 nuts. Torque to 2.3 Nm (20 in-lb).
Refer to Illustration 1.7.

1 Slotted opening for M10 screw 3 M5 nut

2 Stand-os (front and back side of bus bar), indicated by an S in

the drawing

4 Solid motor bus bars

Illustration 1.7 Assembling the Motor Bus Bar Subassembly

5. Install the left and right brake terminals onto the brake terminal bracket using 4 M5 nuts. Torque to 2.3 Nm (20 in-lb).

6. Secure the brake terminal assembly to the AC support bracket with 2 M8 nuts. Torque to 9.6 Nm (85 in-lb).
Refer to Illustration 1.8.

1 AC support bracket 2 Brake terminal assembly (terminals and bracket)

Illustration 1.8 Assembling the AC Support Bracket with the Drive Module 2 Brake Terminal Assembly

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

MI92O102 Danfoss A/S © 04/2016 All rights reserved.

5

Installing the AC Bus Bar Assembly

1. Install 1 side support bracket inside the enclosure on
each side. Secure each side support bracket with 4
M5 screws and torque to 2.3 Nm (20 in-lb). See
Illustration 1.9.

2. Install ground plate assembly. See Illustration 1.9.

2a Attach the ground support bracket to the

inside of the enclosure. Secure with 4 M5
screws and torque to 2.3 Nm (20 in-lb).

2b Install the ground plate onto the 5 studs on

the ground support bar.

2c Secure the bottom of the ground plate to

the enclosure using 8 M5 screws. Torque to

2.3 Nm (20 in-lb).

2d Install the ground bus bar onto the ground

plate. Secure with 5 M8 nuts and torque to
to 9.6 Nm (85 in-lb).

2e Install the 1 ground jumper plate per drive

module. Secure the bottom of the ground
jumper plate to the top of the ground plate
using 1 M5 nut. Torque to 2.3 Nm (20 in-lb).

2f Secure the top of the ground jumper plate

to the bottom of the drive module reusing
the 2 existing M10 nuts. Torque to 19 Nm
(169 in-lb).

3. Install the ground jumper bus bars. Perform this step
for each drive module.

3a Secure the bottom of the ground jumper

bus bar to the ground bus bar using 1 M5
nut. Torque to 2.3 Nm (20 in-lb). See
Illustration 1.9 for the mounting attachment
points on the ground bus bar.

3b Secure the other end of the ground jumper

bus bar to the drive module ground
terminal using 1 M5 nut. Torque to 2.3 Nm
(20 in-lb).

4. Secure the motor bus bar subassembly to the AC bus
bar assembly bracket using 3 M5 nuts. Torque to

2.3 Nm (20 in-lb). Refer to Illustration 1.5.

5. Install the AC bus bar bracket/motor bus bar
subassembly to the side support brackets. Secure
each side with 2 M5 nuts and torque to 2.3 Nm
(20 in-lb).

6. Shape the

exible

bus bars to

t.

7. Install the motor

exible

bus bars for each drive

module. Refer to Illustration 1.10.

7a Insert 1 M10 screw into each of the slotted

holes in the motor bus bar subassembly,
with the screw shaft facing the front.

7b Install 3

exible

motor bus bars per drive
module, securing 1 end to the screw and
the other end to the drive module terminal.
Secure with 2 M10 nuts per bus bar. Torque
to 19 Nm (169 in-lb).

7c Verify that the proper U, V, W connections

are made. Refer to the Terminal Dimensions

section in the VLT

®

Parallel Drive Modules

Installation Guide.

8. Assemble the front EMI/EMC bracket assembly.

8a Attach the left EMI/EMC bracket to the front

EMI/EMC bracket using 3 M5 screws. Torque
to 2.3 Nm (20 in-lb).

8b Attach the right EMI/EMC bracket to the

front EMI/EMC bracket using 3 M5 screws.
Torque to 2.3 Nm (20 in-lb).

9. Install the front EMI/EMC bracket assembly over each
set of

exible

motor bus bars. Secure with 4 M5 nuts
and torque to 2.3 Nm (20 in-lb). Refer to
Illustration 1.11.

10. Install the lower EMI/EMC shield to the AC bus bar
subassembly bracket. Secure with 2 M5 nuts. Torque
to 2.3 Nm (20 in-lb). See Illustration 1.12.

11. Run the mains cables up to the drive module mains
terminals. Secure with the M10 nut that is already
provided on the terminal, and torque to 19 Nm
(169 in-lb).

12. Verify that the proper R, S, T connections are made.

Refer to the Terminal Dimensions section in the VLT

®

Parallel Drive Modules Installation Guide.

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

6

Danfoss A/S © 04/2016 All rights reserved. MI92O102

1 Screw at the bottom of the drive module that connects

to the top of the ground jumper plate

6 Ground bus bar

2 M10 nut 7 Ground jumper bus bar

3 Ground jumper plate 8 Side support bracket

4 M5 nut 9 Ground support bracket

5Ground plate ––

Illustration 1.9 Installation of Side Support Brackets and Ground Bus Bar Assembly

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

MI92O102 Danfoss A/S © 04/2016 All rights reserved.

7

1 Motor bus bar screws for drive module 1 4 M10 nuts

2 Motor bus bar subassembly 5 Flexible motor bus bars

3 Motor bus bar screws for drive module 2 – –

Illustration 1.10 Installation of Flexible Motor Bus Bars

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

8

Danfoss A/S © 04/2016 All rights reserved. MI92O102

1 Left EMI/EMC bracket (shown on drive module 1) 4 Ground plate

2 Front EMI/EMC bracket (shown on drive module 1) 5 Right EMI/EMC bracket (shown on drive module 1)

3 Flexible motor bus bars – –

Illustration 1.11 Installation of Front EMI/EMC Bracket Assembly

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

MI92O102 Danfoss A/S © 04/2016 All rights reserved.

9

1 Mains cable for drive module 1 8 Front EMI/EMC bracket assembly for drive module 2

2 Flexible bus bars for drive module 1 motor terminals 9 Brake terminal assembly for drive module 2

3 Front EMI/EMC bracket assembly for drive module 1 10 Ground bar support bracket

4 AC support bracket 11 Ground bar

5 Brake terminal assembly for drive module 1 12 Ground plate

6 Side support bracket 13 Lower EMI/EMC shield

7 Drive module 2

Illustration 1.12 Installation of Mains Cables

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

10

Danfoss A/S © 04/2016 All rights reserved. MI92O102

Installation Instructions

Bus Bar Kit for 12-pulse, 2-drive System
VLT

®

Series FC 102, FC 202, and FC 302

MI92O102 Danfoss A/S © 04/2016 All rights reserved.

11

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com

*MI92O102*

MI92O102130R0687 04/2016