General Specification
VP4726 / VP4726F
RoHS
Compliant
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO D&T
CORPORATION AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT FOR WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED AND WRITTEN
CONSENT OF D&TCORPORATION.
General Specification
APPROVAL
APPROVEDCHECKEDDRAWN
09.01.2009.01.2009.01.20
1
TABLE OF CONTENTS
1. Overview ----------------- ------------------------------------------------------------------------------ 3
1.1 Scope
1.2 Revision History
2. General Features ------------------------------------------------------------------------------- ------ 4
2.1 General Description
3. Product Specifications ------------------------------------------------------------------------------ 5
3.1 Electrical Specifications
3.2 Entire System Block Diagram
3.3 Signal connector PIN assignments
3.4 GPIO specification
3.5 Environmental and Reliability
4. Regulatory --------------------------------------------------------------------------------------------- 15
4.1 EMC & Safety Agency Approvals
5. OSD specification ------------------------------------------------------------------------------------- 16
5.1 OSD User functions/ Messages
5.2 OSD representation
5.3 OSD System overview
6. Mechanical specification ---------------------------------------------------------------------------- 27
6.1 Product dimension
6.2 Label dimension
6.3 Filter dimension
7. Packing --------------------------------------------------------------------------------------------------- 34
7.1 Packing
General Specification
2
1. Overview
1.1 Scope
VP4726 / VP4726F product has been specifically designed to use the professional applications. This
system has been integrated ADC/TMDS Rx/Video decoder and SDI as well.
Features include high-quality, motion-adaptive deinterlacing up to 1080p with enhanced low-angle
processing, improved low-motion detection, advanced 3D noise reduction, and excellent 3D comb
filter performance for PAL and NTSC.
1.2 Revision History
Change DescriptionParagraphDate
Preliminary release.1.008.10.13
OSD graphic changed.1.108.12.08
OSD graphic changed.1.209.01.20
Panel changed.1.309.10.06
General Specification
3
2.1 General Description
2. General Features
DescriptionItem
VP4726 / VP4726FModel
LCD Panel
Input Signal
GPIO port
Output Signal
Description
Resolution
Deserializer
Cable Equalizer
Cable Driver
VCO
LM260WU2-SLA2 (LG Display)
1920 x 1200 pixel
PW338BC-30LScalar
GS1559-CBE2 ( GENNUM)SDI Processor
GS1574ACNE3 ( GENNUM)
GS1578ACNE3 ( GENNUM)
GO1525-CTAE3 ( GENNUM)
1 x DVI
1 x Optical DVI (VP4726F only)
1 x D-SUB
1 x BNC (SDI)
1 x BNC (CVBS)
2 x BNC (SVHS Y/C)
5 x BNC (Component Y/G, Pb/B, Pr/R, H/CS,VS Input)
3 Function – Primary / Secondary screen swap
– PIP / PBP1 / PBP2 Select
– Record indicator
1 x DVI
1 x BNC (SDI)
Control Key
Unit Dimension
General Specification
AC/DC Adaptor (AC 100~240V, DC 24V 6.25A)Power Supply
Power, Menu, PIP, Up, Down, Plus, Minus, Input
618(W) x 412(H) x 99.5(D) (mm), 8Kg - Without stand
24.330(W) x 16.220(H) x 3.917(D) (inch), 17.64 lbs- Without
stand
4
3.1 Electrical Specifications
3.1.1 Panel
3. Product Specification
UnitDescriptionItem
-LM260WU2-SLA2 (LG Philips)Description
Inch26” DiagonalSize
mm0.2865(W) x 0.2865(H)Pixel Pitch
mm582.0 X 375.6Active area
Surface Treatment
Response Time
(CR≥ 10)
Hard coating(3H), Glare (Low Reflection treatment
of the front polarizer)
pixel1920 x 1200Number of Pixels
-RGB Vertical stripePixel Arrangement
colors16,777,216Number of Colors
Typical1000 : 1 Contrast Ratio
TypicalView Angle Free (R/L 178, U/D 178)Viewing Angle (CR>10)
ms , TypicalRise time (Tr) : 5.5
Fall time (Tf) : 6.5
cd/ m2400 Surface Luminance
Transmissive mode, normally blackDisplay mode
mm, Typical582.0(H) x 375.6(V) x 41.5(D)Panel Dimension
g , Typical3270gWeight
General Specification
5
3.1.2 Power supply
SpecificationItem
UnitMaxTypMin
JMW1150KA2400F09Model No
AC/DC AdapterDescription
Rated Voltage
Rated Line
Frequency
Range
Current
Protection
Configuration
Voltage /Current
Line regulation
Ripple and Noise
Response
100Input
50
240
60
3.00A max at 90Vac input
Dual internal primary current fuse: 250Vac / 5.0A
Inrush limiting : 50A PEAK @ 90~264Vac, 50~60Hz
Inlet type : IEC320-C14,C8
+24Vdc at 6.25AOutput
+24Vdc +/-1%
+24Vdc +/-5%Load regulation
240mV p-p Max @ 90-264Vac, 50~60Hz
: at 20MHz Bandwidth and full load.
0.5ms for 50% Load change TypTransient
Vac, Normal
Vac26490Voltage Range
Hz
Hz6347Line Frequency
Protection
Operating Temperature
Storage Temperature
Humidity
General Specification
20msec min. Over entire input rangeHold-up time
Over-current Protection : 8.125A~9.9A
Short Circuit Protection
Optional Over Voltage Crowbar
0
-30
5
6
40
85
95
℃
℃
%
feet10,0000Altitude
3.1.3 Power management
This monitor saves energy by switching your monitor into a low power mode when it has not detected
a video signal for approximately 45 seconds.
State
POWER OffDPMS suspendDPMS StandbyNormal
Operation
InactiveActiveInactiveActiveHorizontal Sync
InactiveInactiveActiveActiveVertical Sync
BlankedBlankedBlankedActiveVideo
OffGreen Flashing
Less then 20WLess than 20WLess than 20W
Power
GreenPower Indicator
Under 130W
Green Flashing
(5 sec. Interval)
(5 sec. Interval)
Consumption
NOTE : This monitor automatically returns to normal operation when horizontal and vertical sync
return. This occurs when a video signal is detected.
General Specification
7
3.1.4 Input Signal
Video
VGA
Sync
DVI
Optical DVI
CVBS
SVHS Y/C
Applicable maximum
pixel frequency
Type
Range
DescriptionTypeInput Signal
Analog RGBType
DSUB-15Connector
0.7Vp-p ±5%Level
PositivePolarity
75 ohm ±5%Impedance
30 ~ 93KHzHorizontal frequency
50 ~ 85HzVertical frequency
170MHz
1920x1200 / 60Hz (154MHz Timing, NON-CRT)Maximum resolution
Separate H/V sync, Composite H/V sync, Sync On
Green Automatic synchronization without external
switch
TTL Level (V high ≥2.0V, V low ≤0.8V)Level
Positive or NegativePolarity
Automatic synchronization for applicable
resolution modes which follows industrial standard
within frequency range of 30 to 93KHz in
horizontal and 50 to 85Hz in vertical
more than 2KΩTerminal resistance
Digital RGBType
TMDS single linkSignal Format
DVI-DConnector
Digital RGBType
Fiber Optic TransmissionSignal Format
C-VideoType
NTSC, PALColor system
Composite Video SignalSignal Format
S-VideoType
NTSC, PALColor system
Y/C Separated Video SignalSignal Format
SDI
General Specification
SMPTE-274M
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF)
720p (60 / 59.94 / 50)SMPTE-296M
1035i (60 / 59.94)SMPTE-260M
480i (59.94)SMPTE-125M
576i (50) ITU-R BT.656
8
3.1.5 Output Signal
DescriptionTypeOutput Signal
Digital RGBType
DVI
SMPTE-274M
SMPTE-296M
SDI
SMPTE-260M
SMPTE-125M
ITU-R BT.656
3.1.6 Input Signal Timing
Resolution
640 x 350 @60Hz
640 x 350 @70Hz
640 x 350 @85Hz
640 x 400 @60Hz
TMDS single linkSignal Format
DVI-DConnector
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF)
720p (60 / 59.94 / 50)
1035i (60 / 59.94)
480i (59.94)
576i (50)
Horizontal
frequency
(KHz)
Vertical
frequency
(Hz)
Pixel clock
(MHz)
25.17559.94131.469
25.17570.08731.469
31.50085.08037.86
25.17559.94131.469
640 x 400 @70Hz
800 x 600 @72Hz
800 x 600 @75Hz
800 x 600 @85Hz
General Specification
48.077
25.17570.08731.469
31.50085.08037.86640 x 400 @85Hz
25.17559.94031.469640 x 480 @60Hz
31.50072.80937.861640 x 480 @72Hz
31.50075.00037.500640 x 480 @75Hz
36.00085.00843.269640 x 480 @85Hz
35.50085.03837.927720 x 400 @85Hz
36.00056.25035.156800 x 600 @56Hz
40.00060.31737.879800 x 600 @60Hz
50.00072.188
75.00046.875
49.500
56.25085.06153.674
44.90086.95835.5221024 x 768 @43Hz
9
Resolution
Horizontal
frequency
(KHz)
Vertical
frequency
(Hz)
Pixel clock
(MHz)
65.00060.00448.3631024 x 768 @60Hz
75.00070.06956.4761024 x 768 @70Hz
78.75075.02960.0231024 x 768 @75Hz
94.50084.99768.6771024 x 768 @85Hz
80.00060.05354.3481152 x 864 @60Hz
1152 x 864 @70Hz
1600 x 1200 @60Hz (**)
1600 x 1200 @60Hz
1920 x 1200 @60HZ
(**) Preferred Timing for 1600 x 1200 @60Hz input
70.01663.955
94.200
108.00075.00067.5001152 x 864 @75Hz
108.00060.00060.0001280 x 960 @60Hz
148.50085.00285.9381280 x 960 @85Hz
108.50060.01363.9741280 x 1024 @60Hz
135.00075.02579.9761280 x 1024 @75Hz
157.50085.02491.1461280 x 1024 @85Hz
130.37559.98174.077
162.00060.00075.000
148.50060.00067.5001920 x 1080 @60Hz
154.12559.99974.099
General Specification
10
3.2 Entire System Block Diagram
General Specification
11
3.3 Signal connector PIN assignments
( VP4726F only)
General Specification
12
3.4 GPIO specification
P,S Swap
1
Pressing the swap button.
Swaps the primary and
secondary images.
2
PIP,PBP1,PBP2 Select
The selection of secondary Image
position button is pressed.
SINGLE
PIP PBP1 PBP2
P
3
Record Indicator
The record indicator is displayed while
a contact closure to the ground pin
is present, the indicator is removed
when the contacts are opened.
The record indicator is displayed in the
monitor’s top left corner.
S
P
GND
4
Common ground
REC
S
P
S P SP
General Specification
* GPIO mating connector : RJH 4pin
(telephone handset connector)
RJ9
1234
GPIO
13
3.5 Environmental specification
DescriptionItem
Temperature 0℃~ 40℃Operating Conditions
5% ~ 85%, non-condensingHumidity
-20℃~ 60℃TemperatureTransportation
Conditions
5% ~ 95%, non-condensingHumidity
-20℃~ 60℃TemperatureStorage Conditions
10% ~ 85%, non-condensingHumidity
3.6 Reliability specification
MTBF : more than 30,000 hours at 90% confidence level, excluding LCD panel.
Reliability items :
3.6.1 Stress / Time acceleration T est
Time (hr)Temp (℃)
Test ResultsCondition
3.6.2 Temperature Cycle Test
No Damage7240 ± 2
General Specification
Test ResultsCondition
Time (hr)Temp (℃)
No Damage95-20~40 ± 2
14
4. Regulatory
4.1 EMC & Safety Agency Approvals
UL Safety Compliance:
This LCD monitor is investigated to UL60601-1,
1st Edition, 2006-04-26 (Medical Electrical
Equipment, Part 1:General Requirements for
Safety)CAN/CSA-C22.2 No. 601.1-M90, 2005
(Medical Electrical Equipment - Part 1:General
Requirements for Safety)
CB Compliance:
This LCD monitor is investigated to
EN 60601-1: 1990 + A1:1993 + A2:1995
CE-EMC Compliance:
This LCD monitor is investigated to
EN 60601-1-2: 2001 + EN2001-1-2+ A1:
2006( IEC60601-1-2:2001 + A1:2004)
CE-LVD Compliance:
This LCD monitor is investigated to EN 606011: 1990 + A1:1993 + A2:1995+ A13:1996 :
IEC60601-1:1988 + A1:1991 + A2:1995 +
corrigendum 1995,mod.
FCC Compliance:
This LCD monitor is investigated to
FCC Part 15
General Specification
15
5. OSD specification
VP4726 / VP4726F gives various and very easy graphic user interface. User can easily access function. 8
button keypad, located on the front of monitor, allows the user to make adjustments to various display
parameters using on screen menus easily.
Be sure that your system power and LED is turned on before operating key board.
5.1 OSD User functions/ Messages
5.1.1 OSD indicator
DescriptionKey Name
Soft power Turns ON/OFF the monitor.Power
Menu
PIP
UP (▲)
Down (▼)
Plus (+)
Minus (-)
Input
- With OSD deactivated, Activated to OSD menu.
- With OSD activated, Exit from main menu or sub menu.
Enable PIP (Picture in Picture) function.
- Select PIP,PBP1,PBP2
- With OSD deactivated, Hot key of the brightness control and increases
the brightness.
- With OSD activated, move the OSD cursor upward.
- With OSD deactivated, Hot key of the brightness control and decreases
the brightness.
- With OSD activated, move the OSD cursor downward.
- With OSD deactivated, Hot key of the contrast control and increases
the contrast.
- With OSD activated, enter sub menu and increases the adjustment of
the selected function.
- With OSD deactivated, Hot key of the contrast control and decreases
the contrast.
- With OSD activated, decreases the adjustment of the selected function.
Change the display signal source.
-Select DVI OPTICAL(VP4726F) / DVI DIGITAL / DSUB ANALOG / SDI
/ YPbPr / RGBS / SVIDEO / CVIDEO
-With OSD deactivated, Hot key of the auto adjustment control when it
pressed over 1 second at DSUB ANALOG source.
5.1.2 INPUT source select
General Specification
16
5.2 OSD representation
5.2.1 DSUB ANALOG / RGBS input source
ADJUST
COLOR TEMP
Function DescriptionsSub-menusMenus
Increase or decrease the brightness (Range : 0~100)BRIGHTNESS
Increase or decrease the contrast (Range : 0~100)CONTRAST
Changes the tone of color (Range : 0~100)SATURATION
Changes the richness of color (Range : 50~0~50)COLOR
Increase or decrease the sampling frequency (Range : 0~100)CLOCK
Increase or decrease the Phase level (Range : 0~100)PHASE
Adjust backlight dimming level (Range : 0~100)BACKLIGHT
Fit to the most appropriate screen on the D-SUB Analog signalAUTO ADJ UST
Change the color temperature mode ( 6500K, 5600K, USER )MODE
Red balance (Only works with USER mode) (Range : 0~100)RED
Green balance (Only works with USER mode) (Range : 0~100)GREEN
Blue balance (Only works with USER mode) (Range : 0~100)BLUE
IMAGE
SETUP
PIP
IMAGE SETTING
DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
ENTRY
Change the image size (Full, Fill aspect, 1:1, Normal)IMAGE SIZE
Adjust the horizontal position of the displayed source image. (Range : 0~100)H POSITION
Adjust the vertical position of the displayed source image. (Range : 0~100)V POSITION
Adjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMA
Set the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTER
Adjust the displayed size.(0~8)OVER SCAN
Change the image setting. (Preset 1,2 / User 1,2,3)
Enlarge the image, move image left and rightZOOM / PAN
Keep still the imageFREEZE FRAME
Change the OSD language (8 language)LANGUAGE
Change the OSD position ( 9 positions )OSD POSITION
Adjust time until the OSD Menu will disappear after adjusting the menu. (5,
10, 20, 30, 60, 90, 120, 180, 240 seconds)
Changes the all OSD value to factory outgoing status.
Disable or enable auto source select. (ON: Searches through all possible
input source until an active video source is found. OFF: Video input is
manually selected.)
Change the name of a Preset to the Users Name, etcUSER NAME
Change the layout. (Single, PIP, PBP1, PBP2)LAYOUT
Change the secondary input source.SOURCE
Change the PIP size. (Small, Large)SIZE
Change the PIP position.POSITION
Swaps the position of the Primary and Secondary images.SWAP
General Specification
17
5.2.2 DVI OPTICAL / DVI DIGITAL input source
ADJUST
Increase or decrease the brightness (Range : 0~100)BRIGHTNESS
Increase or decrease the contrast (Range : 0~100)CONTRAST
Changes the tone of color (Range : 0~100)SATURATION
Changes the richness of color (Range : Green 0~50, Red 0~50)COLOR
Adjust backlight dimming level (Range : 0~100)BACKLIGHT
Function DescriptionsSub-menusMenus
COLOR TEMP
IMAGE
SETUP
PIP
IMAGE SETTING
DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
ENTRY
Change the color temperature mode ( 6500K, 5600K, USER )MODE
Red balance (Only works with USER mode) (Range : 0~100)RED
Green balance (Only works with USER mode) (Range : 0~100)GREEN
Blue balance (Only works with USER mode) (Range : 0~100)BLUE
Change the image size (Full, Fill aspect, 1:1, Normal)IMAGE SIZE
Adjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMA
Set the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTER
Adjust the displayed size.(0~8)OVER SCAN
Change the image setting. (Preset 1,2 / User 1,2,3)
Enlarge the image, move image left and rightZOOM / PAN
Keep still the imageFREEZE FRAME
Change the OSD language (8 language)LANGUAGE
Change the OSD position ( 9 positions )OSD POSITION
Adjust time until the OSD Menu will disappear after adjusting the menu. (5,
10, 20, 30, 60, 90, 120, 180, 240 seconds)
Changes the all OSD value to factory outgoing status.
Disable or enable auto source select. (ON: Searches through all possible
input source until an active video source is found. OFF: Video input is
manually selected.)
Change the name of a Preset to the Users Name, etcUSER NAME
Change the layout. (Single, PIP, PBP1, PBP2)LAYOUT
Change the secondary input source.SOURCE
Change the PIP size. (Small, Large)SIZE
Change the PIP position.POSITION
Swaps the position of the Primary and Secondary images.SWAP
General Specification
18
5.2.3 YPbPr input source
ADJUST
COLOR TEMP
Function DescriptionsSub-menusMenus
Increase or decrease the brightness (Range : 0~100)BRIGHTNESS
Increase or decrease the contrast (Range : 0~100)CONTRAST
Adjusts the sharpness of video image (Range : 0~100)SHARPNESS
Changes the tone of color (Range : 0~100)SATURATION
Changes the richness of color (Range : Green 0~50, Red 0~50)COLOR
Adjust backlight dimming level (Range : 0~100)BACKLIGHT
Increase or decrease the sampling frequency (Range : 0~100)CLOCK
Increase or decrease the Phase level (Range : 0~100)PHASE
Change the color temperature mode ( 6500K, 5600K, USER )MODE
Red balance (Only works with USER mode) (Range : 0~100)RED
Green balance (Only works with USER mode) (Range : 0~100)GREEN
Blue balance (Only works with USER mode) (Range : 0~100)BLUE
IMAGE
SETUP
PIP
IMAGE SETTING
DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
ENTRY
Change the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZE
Adjust the horizontal position of the displayed source image. (Range : 0~100)H POSITION
Adjust the vertical position of the displayed source image. (Range : 0~100)V POSITION
Adjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS,GAMMA
Set the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTER
Adjust the displayed size.(0~8)OVER SCAN
Change the image setting. (Preset 1,2 / User 1,2,3)
Enlarge the image, move image left and rightZOOM / PAN
Keep still the imageFREEZE FRAME
Change the OSD language (8 language)LANGUAGE
Change the OSD position ( 9 positions )OSD POSITION
Adjust time until the OSD Menu will disappear after adjusting the menu. (5,
10, 20, 30, 60, 90, 120, 180, 240 seconds)
Changes the all OSD value to factory outgoing status.
Disable of enable auto source select.
(ON: Searches through all possible input source until an active video source
is found. OFF: Video input is manually selected.)
Change the name of a Preset to the Users Name, etcUSER NAME
Change the layout. (Single, PIP, PBP1, PBP2)LAYOUT
Change the secondary input source.SOURCE
Change the PIP size. (Small, Large)SIZE
Change the PIP position.POSITION
General Specification
Swaps the position of the Primary and Secondary images.SWAP
19
5.2.4 SVIDEO / CVIDEO input source
ADJUST
Function DescriptionsSub-menusMenus
Increase or decrease the brightness (Range : 0~100)BRIGHTNESS
Increase or decrease the contrast (Range : 0~100)CONTRAST
Adjusts the sharpness of video image (Range : 0~100)SHARPNESS
Changes the tone of color (Range : 0~100)SATURATION
Changes the richness of color (Range : Green 0~50, Red 0~50)COLOR
Adjust backlight dimming level (Range : 0~100)BACKLIGHT
COLOR TEMP
IMAGE
SETUP
PIP
IMAGE SETTING
DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
ENTRY
Change the color temperature mode ( 6500K, 5600K, USER )MODE
Red balance (Only works with USER mode) (Range : 0~100)RED
Green balance (Only works with USER mode) (Range : 0~100)GREEN
Blue balance (Only works with USER mode) (Range : 0~100)BLUE
Change the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZE
Adjust the horizontal position of the displayed source image. (Range : 0~100)H POSITION
Adjust the vertical position of the displayed source image. (Range : 0~100)V POSITION
Adjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMA
Set the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTER
Adjust the displayed size.(0~8)OVER SCAN
Change the image setting. (Preset 1,2 / User 1,2,3)
Enlarge the image, move image left and rightZOOM / PAN
Keep still the imageFREEZE FRAME
Change the OSD language (8 language)LANGUAGE
Change the OSD position ( 9 positions )OSD POSITION
Adjust time until the OSD Menu will disappear after adjusting the menu. (5,
10, 20, 30, 60, 90, 120, 180, 240 seconds)
Changes the all OSD value to factory outgoing status.
Disable of enable auto source select. (ON: Searches through all possible
input source until an active video source is found. OFF: Video input is
manually selected.)
Change the name of a Preset to the Users Name, etcUSER NAME
Change the layout. (Single, PIP, PBP1, PBP2)LAYOUT
Change the secondary input source.SOURCE
Change the PIP size. (Small, Large)SIZE
Change the PIP position.POSITION
Swaps the position of the Primary and Secondary images.SWAP
General Specification
20
5.2.5 SDI input source
ADJUST
Function DescriptionsSub-menusMenus
Increase or decrease the brightness (Range : 0~100)BRIGHTNESS
Increase or decrease the contrast (Range : 0~100)CONTRAST
Changes the tone of color (Range : 0~100)SATURATION
Changes the richness of color (Range : Green 0~50, Red 0~50)COLOR
Adjust backlight dimming level (Range : 0~100)BACKLIGHT
COLOR TEMP
IMAGE
SETUP
PIP
IMAGE SETTING
DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
ENTRY
Change the color temperature mode ( 6500K, 5600K, USER )MODE
Red balance (Only works with USER mode) (Range : 0~100)RED
Green balance (Only works with USER mode) (Range : 0~100)GREEN
Blue balance (Only works with USER mode) (Range : 0~100)BLUE
Change the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZE
Adjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMA
Set the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTER
Adjust the displayed size.(0~8)OVER SCAN
Change the image setting. (Preset 1,2 / User 1,2,3)
Enlarge the image, move image left and rightZOOM / PAN
Keep still the imageFREEZE FRAME
Change the OSD language (8 language)LANGUAGE
Change the OSD position ( 9 positions )OSD POSITION
Adjust time until the OSD Menu will disappear after adjusting the menu. (5,
10, 20, 30, 60, 90, 120, 180, 240 seconds)
Changes the all OSD value to factory outgoing status.
Disable of enable auto source select.
(ON: Searches through all possible input source until an active video source
is found. OFF: Video input is manually selected.)
Change the name of a Preset to the Users Name, etcUSER NAME
Change the layout. (Single, PIP, PBP1, PBP2)LAYOUT
Change the secondary input source.SOURCE
Change the PIP size. (Small, Large)SIZE
Change the PIP position.POSITION
Swaps the position of the Primary and Secondary images.SWAP
General Specification
21
5.3 OSD overview
Function DescriptionsMenus
BRIGHTNESS
CONTRAST
CLOCK
PHASE
BACKLIGHT
AUTO ADJUST
SHARPNESS
SATURATION
COLOR
COLOR TEMP 6500K
COLOR TEMP 5600K
COLOR TEMP USER
IMAGE SIZE
Press the BRIGHTNESS button to display the ADJUST menu or UP,DOWN hot key.
Setting the brightness too high or too low will decrease the amount of visible grayscales.
Press the CONTRAST button to display the ADJUST men u or +,- hot key.
Setting the Contrast too high or too low will cause loss of some grayscales.
Do not adjust freely. It will adjust fine state automatically after auto adjustment.
When frequency value is wrong, the horizontal image have a wrongsize or noise.
Do not adjust freely. It will adjust fine state automatically after auto adjustment.
When phase value is wrong, the image have a noise.
Adjust backlight dimming level.
Setting the backlight too low will cause dark image and too high will decrease the backlight lifetime.
Fit to the most appropriate screen on the D-SUB Analog signal
Adjusts the sharpness of video image
Changes the tone of color
Changes the richness of color (Range : Greenish 0~50, Reddish 0~50)
Default 6500K color setting
Default 5600K color setting
Default 6500K color setting. When USER is selected, Red, Green and Blue values are changeable by the
user
*DSUB / DVI OPTICAL / DVI DIGITAL input source
FULL FILL ASPECT
*YPbPr / RGBS / SDI / CVIDEO / SVIDEO input sour ce
General Specification
1:1 NORMAL
FULL FILL ASPECT 1:1
NORMAL ANAMORPHIC
22
CAUTION : FILL ASPECT,NORMAL
Size are depends on input size ratio
CAUTION : FILL ASPECT,NORMAL,
ANAMORPHIC Size are depends on
input size ratio
Function DescriptionsMenus
H POSITION
V POSITION
GAMMA
Adjusts the horizontal position of the image. It will return to the default state when executing AUTO
ADJUST or RESET SETTINGS
Adjusts the horizontal position of the image. It will return to the default state when executing AUTO
ADJUST or RESET SETTINGS
Adjusts the gamma curve of video image.
1.8 2.0 2.2 2.4 2.6 PACS VIDEO
< NOTICE > BYPASS is depend on panel gamma value, please refer to the panel specification
FILTER
OVER SCAN
Adjusts the sharpness of video image.
SHARPEST
SHARP
NORMAL
SOFT
SOFTEST
Enable 10% over scan of original input image
0 : 1 : 2 :
3 :
6 : 7 :
4 : 5 :
8 :
General Specification
23
Function DescriptionsMenus
IMAGE SETTING
ZOOM / PAN
Save the 5 user’s setting about BRIGHTNESS,CONTRAST,COLOR TEMP,FILTER value separately.
(PRESET 1~2, USER 1~3)
Controls the zoom in/out of the image.
0 step : 4 step : 9 step :
13 step : 18 step : 22 step :
26 step : 30 step :
Controls the PAN in/out of the image.
FREEZE FRAME Freeze the main image. Do not support secondary image freeze at PIP mode
LANGUAGE
OSD POSITION
Change the OSD language (8 language)
ENGLISH / GERMAN / FRENCH / SPAINISH / ITALIAN / JAPANESE / CHINESE / KOREAN
Adjust the position of OSD
General Specification
24
OSD DURATION
RESET SETTINGS
AUTO SOURCE
SELECT
Function DescriptionsMenus
Adjust the time until the OSD Menu will disappear after adjusting the menu
Reset the unit to factory outgoing status.
When AUTO SOURCE SELECT is on, the monitor automatically search input source except PIP sub
Source.
USER NAME ENTRY
PIP LAY OUT
PIP SOURCE
VP4726F only
PIP SIZE
Put user’s name or etc into set.
Change sub window layout (SINGLE,PIP,PBP1,PBP2)
PIP : Main/Sub window doesn’t change aspect ratio.
PBP1 : Main/Sub window doesn’t change aspect ratio.
PBP2 : Main/Sub window H/V display 1:1 size.
Select PIP source input. You can change other sub windows through OSD pip menu. Below chart is PIP
matching table with main and sub window.
Sub window
M
a
I
n
w
I
n
d
o
w
DVI
OPTICAL
DVI DIGITAL
DSUB
ANALOG
SDI
YPbPr
RGBS
CVIDEO
SVIDEO
DVI
OPTICAL
X
O
O
O
O
O
O
O
DVI
DIGITALInput source
DSUB
ANALOG
SVIDEOCVIDEORGBSYPbPrSDI
O¹ : Support up to UXGA,60Hz (162MHz)
When main window is running at 1080p,sub window supports up to 1080i mode only.
When main window is running below 1080i,sub window supports up to 1080p mode.
Change PIP mode sub window size.
SMALL LARGE
OOOOOOO
OOXXOXX
OOXXO¹XX
XXO¹O¹XO¹O
OOXXO¹XX
OOXXO¹XX
XXOOXOO
XXOOXOO
PIP POSITION
General Specification
Sub
Main
25 % / Panel size 33 % / Panel size
* CAUTION : Do not change input Source aspect ratio and the pip image size is changeable depend on
Change PIP mode sub window position.
Sub
input timing.
Main
Main
Sub
Main
Main
Sub
Main
Sub
25
Sub
Main
Sub
Main
Sub
Sub
Main
Main
Sub
Main
Sub
Function DescriptionsMenus
SWAP
Change main window and sub window position on PIP,PBP1,PBP2.
Sub
Main
PIP
Sub
Main
PBP1
SubMain SubMain
PBP2
SubMain SubMain
General Specification
26
6.1 Product dimension
6. Mechanical Specifications
General Specification
27
6.2 Label dimension
6.2.1 Connector (Function) label
6.2.2 Product label
ConMed LinvatecBrand Logo
VP4726 / VP4726FModel NO.
(This may vary based on the
Customer's request, and the
changed contents of the Rating
Label shall not be specified in
this specification.)
LocationRating Label
Tilt
Base Color
The left bottom side of rearcover
Shall not be tilted more than
1mm
140X31(mm)Size
Polyester film (75Demicron)Material
The color same as rear
housing(Gray)
General Specification
28
6.2.3 AC ADAPTOR Label
The center of rear-coverLocation
Label shall not be tilted more than 1mm Tilt
57.5 x 64.5 (mm)Size
Polyester film 125uMaterial
BlackBase Color
General Specification
29
6.2.4 BOX label
The left and right center side Location
Shall not be tilted more than 1mmTilt
161X63.5(mm)Size
Art paperMaterial
WhiteBase Color
6.2.5 Membrane switch
General Specification
The center bottom side of front bezelLocation
Shall not be tilted more than 1mmTilt
185X38.5(mm)Size
Pc auto texMaterial
The color same as front bezelBase Color
30
6.3 Filter dimension
6.3.1 General specification
UnitDescriptionItem
mm(576 +0/-1mm) x (356 +0/-1mm) x (3±0.3mm)Size
nmLess than 1% (450 ~600nm)Average reflectance
Double side Anti-Reflection coatingCoating
Transmittance
Reflection color
%97% (at 545nm of the wavelength)
(The average transmittance in the range of 450 ~ 650nm should be
97%)
Between Blue-Violet & Red-Violet
No harmful defect such as void, groove, and contaminationAppearance
No contamination, No discoloration, No alien substanceSurface
General Specification
31
7.1 Packing
7.1.1 Carton Dimension
7. Packing
Width
750 mm
This unit conforms to all specifications in the "General Specification
VP4726 / VP4726F ” document, dated 09.01.20
Depth
230 mm
Height
657 mm
Weight
14.5Kg
General Specification
32
7.1.2 Accessory
General Specification
33
Loading...