User’s Manual
52” Dual Color TFT LCD Monitor
Model Name : FS-S5202C
Model Number : 0100400003AA
Customer Project name : Aquarius Dual
TANDBERG Page 1 of
Item number : Item name :
117336
Date Sign Changes : Rev 01
Init
Tech
App
Vendor Vendor/Manufacturer Part No FS-S5202C 0100400003AA
Vendor/Manufacturer must guarantee that assembly is in compliance with RoHS directive(tick-off)
TANDBERG Monitor Dual 52” Assembly Rev.:01-draft
First build of the specification
All contents are confidential
Do not copy
INFORMATION TO USER :
General Specification
1. General Description and Scope
2.1 General Description
This specification applies to the Type 52” Color TFT/LCD Module “LTI520HB01”. This module is
designed for a LCD TV style display unit. The screen format and electrical interface are intended to
support the VESA WUXGA (1920(H) ×1080(V) at 60Hz) screen. Supported Color is native 16.7M
colors (RGB-8bit data driver).
All input signals are LVDS (Low Voltage Differential Signaling) interface compatible.
2. Environmental and Reliability Specifications
3.1 Operating Conditions
3.1.1 Temperature : 0℃~ 40℃
Note : Max. Operating Temperature 40℃ in the spec means the temperature measured at the
point of the front surface of the LCD glass cell.
3.1.2 Humidity : 10% ~ 90%, non-condensing
3.1.3 Altitude : maximum 4,500m
3.1.4 Test
Type Parameters Description and comments Results
Low
temperature
T = 0°C
Dwell time = 8h + 2h (power-off)
Cold start-up after the power-off
period
Lab
amb
1h
0.5h
1h
0.5h
Passed
0
8h
2h
High
temperature
Low
pressure
Document No. D&TQP0302-11(0) Revision No. 01 Page 2 of 22
T = +40°C
Dwell time = 8h + 2h (power-off)
Warm start-up after the power-off
period
P = 60kPa (4206m)
Pressure dwell time = 2h
T = +40°C
0.1h
2h
0.1h
2h
0.5h
0.5h
Lab
amb
Shield the unit against direct airflow
Lab
amb
Shield the unit against direct airflow
1h
1h
8h
0.5h
3.5h 2.5h
0.5h
1h
1h
Passed
Passed
3.2 Non-Operational Conditions
3.2.1 Temperature : -20℃~ 60℃
3.2.2 Humidity : 10% ~ 90%, non-condensing
3.2.3 Altitude : maximum 15,000m
3.2.4 Test
Type Parameters Description and comments Results
Low
temperature
T = -20°C
Dwell time = 16h
Passed
High
temperature
Thermal
shock
Humidity RH = 90%
T = +60°C
Dwell time = 16h
Low temperature = -20°C
High temperature = +60°C
Temperature gradient =
5°C/min
Dwell time = 2h
No. of cycles = 3
Low temperature = 30°C
High temperature = 60°C
No. of cycles: 5 ea 24h
Passed
Passed
3h
9h
3h
9h
60
30
Passed
One cycle
Document No. D&TQP0302-11(0) Revision No. 01 Page 3 of 22
3.3 Packing Conditions
3.3.1 Temperature : -20℃~ 50℃
3.3.2 Humidity : 10% ~ 90%, non-condensing
3.3.3 Altitude : maximum15,000m
3.3.4 Test
Type Parameters Result
Freefall Drop
Drop surface Concrete or steel
Drop height Weight > 100kg: 0.1m
Impact area 6 faces
Passed
1 selected corner
1 selected edge
vibration
No. of drops 1 per impact area
Frequency range 5-10Hz 10-50Hz
Displacement 3.5mm
Acceleration 1g
Sweep rate 3min(5-50-5)
Duration Right/Left : 15min
Front/Back : 15min
Up/Down : 30min
Passed
Document No. D&TQP0302-11(0) Revision No. 01 Page 4 of 22
3. Input Signal and AC Power
4.1 AC Power
4.1.1 AC input voltage : AC 100 to 240 Volts (Universal power)
4.1.2 AC input frequency : 50~60Hz ±3Hz
4.2 Video and Sync Signal
4.2.1 Video signal
A. Horizontal frequency : 25 ~ 90KHz
B. Vertical frequency : 24 ~ 120Hz
C. Applicable maximum pixel frequency : 170MHz(Analog), 165MHz(Digital)
D. Maximum resolution : 1920x1200 / 60Hz
4.2.2 Signal connectors
A. HDMI type Ax3x2(Dual) : HDMI input
B. 15p D-Sub(Female, 3row) x1x2(Dual) : Analog RGB input
C. 9p D-Sub (Female) x1x2(Dual) : RS232C Input
D. 9p D-Sub (Male) x1x2(Dual) : RS232C Output
E. 15p D-Sub(Male, 2row) x1x(Dual) : Audio AMP signal input
F. AC Inlet x1x2(Dual) : main AC power input
4. Electrical Performance: Except where noted, the following test conditions are required.
5.1 Standard Testing Conditions
5.1.1 AC power voltage and frequency : AC 100 ~ 240V±10%, 60Hz/50Hz±3Hz
5.1.2 Ambient temperature: 25℃± 5℃
5.1.3 Brightness setting : set brightness control to the maximum level of the OSD
5.1.4 LCD panel direction : test at the parallel position with LCD panel center line
5.1.5 Ambient light level : between 300 lux and 700 lux
5.2 Power management
5.2.1 Power management
: This system can save energy by switching this monitor into a low-mode when the display video
signal is none. But power Management system can not be corresponded with VESA DPMS,
because of the TANDBERG’s operation specification.
5.2.1 Power Management Modes.
Normal operation Max 1000Wrms
DPMS or Standby mode Max 50Wrms
Sleep mode Max 3.5Wrms
Document No. D&TQP0302-11(0) Revision No. 01 Page 5 of 22
State Power consumption
5.3 LCD (Liquid Crystal Display) Panel Specifications
This specification applies to the Type 52” Color TFT/LCD Module “LTI520HB01”. This module is
designed for a LCD TV style display unit.
The screen format and electrical interface are intended to support the WUXGA(1920(H) ×1080(V))
screen. Supported gray scales are native 8bit per 1(one) sub pixel. All input signals are LVDS(Low
Voltage Differential Signaling) interface compatible.
5.3.1 General specification
Item SPECIFICATION UNIT NOTE
diagonal 1321 mm Display
area
Driver element a-Si TFT Active matrix
Number of Pixels 1920x1080, 2.07Million pixels
Pixel Pitch 0.6(H) ×0.6(V) mm
Pixel arrangement R. B, G Vertical Stripe
Display colors 16.7M (RGB 8-bit data)
Viewing angle(max) 178(H), 178(V) degrees 120 minutes after lighting on
Display mode Normally black
viewable 1152.0(H) × 648.0(V) mm
5.3.2 Optical characteristics (LCD panel specification)
The following optical characteristics are measured under stable conditions. It takes about
120minutes to reach stable conditions. The measuring point is the center of display area
unless otherwise noted.
The optical characteristics should be measured in a dark room or equivalent state.
Measuring equipment : TOPCON BM-7, SPECTRORADIOMETER SR-3
Temperature of LCD surface=25℃, VDD=12.0V, fV=60Hz, BRT=High(PWM Duty 100%)
ITEM SYMBOL CONDITION Min. Typ. Max. UNIT
Contrast Ratio C/R 1300 1700 - -
Response
Time
Brightness of white Bwh 500 600 - cd/m²
Color
Chromaticity
(CIE)
Viewing
Angle
Rise Tr - 14 24 ms
Fall Tf - 8 10 ms
Red
Green
Blue
White
Hor
Ver
x 0.645
y 0.336
x 0.275
y 0.606
x 0.143
y 0.067
x 0.280
y
θL 75 89 θR 75 89 -
θU 75 89 θD
θ=0°
1)
TYP
-0.03
0.290
75 89 -
TYP
+0.03
Degree
-
Document No. D&TQP0302-11(0) Revision No. 01 Page 6 of 22
Normal Line
o
φ = 0
θ L
φ L
L
=90
o
x
θ
φ H
,
θ = 0
o
θ R
y
φ
= 90o
H
φ
= 90o
L
x*y*
θ
=90
R
Definition of Response time :
Display data
Opt i ca l
Response
100%
90%
Black(TFT OFF)
TR
White(TFT ON)
Black(TFT OFF)
TF
10%
0%
Time
5.3.3 Luminance Uniformity
When the backlight is on with all pixels in the white (maximum gray) level, the luminance
uniformity is defined as follow;
Where;
L
L
Adjacent Area
Luminance Uniformity = ( L
Over a circular area of 10mm diameter placed anywhere on the screen
Screen Total
Luminance Uniformity = ( L
Over the entire screen
5.4 Front of screen (FOS) performance
5.4.1 Chromaticity(White) : X = 0.280, Y = 0.290
5.4.2 Luminance : no less than 500㏅/㎡
Controls setting condition : contrast and brightness max
Document No. D&TQP0302-11(0) Revision No. 01 Page 7 of 22
: The luminance of the brightest part of the area
bright
:The luminance of the darkest part of the area
dark
- L
bright
bright
- L
dark
dark
) / L
) / L
≤ 0.25
bright
≤ 0.25
bright
o
5.4.3 Minimum luminance : less than 30cd/㎡ with full white pattern at the contrast default and
minimum brightness and minimum back light level
5.4.4 Gray scale linearity : The 16 step gray bars shall be distinguishable at the default contrast and
default brightness or 3 steps down contrast setting of the OSD menu
5.4.5 Noise : Pixel displacement, jitter, or swim shall not be visible to the eye when viewed at 50cm
from the LCD panel surface.
5.5 Defect
: Defects are considered to be impairments to video quality, which exist independently of
displayed information. They may be electrical, mechanical, or physical imperfection of
display resulting from processing, handling, shipping, etc.
5.5.1 Bright and Black Dots
The following Table describes the specification of bright and black dots
screen quality of
the TFT-LCD module at power-ON.
in the visual
Items Specification
Any Bright Dots(Two joined dot must be counted 2)
Any Black Dots(Two joined dot must be counted 2)
Bright and Black Dots(total)
Two Joined Bright Dots
Three Joined Bright Dots.
Two joined Black Dots
Three Joined Black Dots
Minimum distance between dot defects
Bright dot – Bright dot
Black dot – Black dot
Basic Conditions:
Viewing Distance 1500±10 mm
Ambient Illumination 300~700 lux(Normal 500lux)
Ambient Temperature 25±5 ℃
5x2 Max
10x2 Max
15x2 Max
1x2 Max
1x2 Max
2x2 Max
1x2 Max
5mm
Ignore
5.5.2 Visual Screen Quality
Item Size(mm) Permissible
Operation Condition
Number
(in the polarizer, Cell)
Bright Foreign Material
Circular
Linear
0.3∠D≤3.0
2∠L≤15.0
0.3≤D≤0.5
5 with white picture Foreign Material
5 with white or black picture
5 with black picture
(in polarizer or cell)
Scratches on the polarizer / glass
Dent on the polarizer / glass
2∠L≤15.0
0.3≤D≤0.8
5
10
Non operation
z D: Average Diameter, L: Length,
Document No. D&TQP0302-11(0) Revision No. 01 Page 8 of 22
5. Signal Connections and Pin Assignments
6.1 AC Inlet socket
Pin
1 Live
2 Neutral
3 GND
6.2 HDMI Connector (Type A)
Signal Assignment
Pin Signal Assignment Pin Signal Assignment
1
TMDS Data2+
3
TMDS Data2-
5
TMDS Data1 Shield
7
TMDS Data0+
9
TMDS Data0-
11
TMDS Clock Shield
13
NC
15
DDC SCL
17
DDC Ground
19
Hot Plug Detect
Document No. D&TQP0302-11(0) Revision No. 01 Page 9 of 22
2 TMDS Data2 Shield
4 TMDS Data1+
6 TMDS Data1-
8 TMDS Data0 Shield
10 TMDS Clock+
12 TMDS Clock-
14 NC
16 DDC SDA
18 +5V Power
6.3 15pin D-Sub Connector : Analog RGB signal input
Pin Signal Assignment Pin Signal Assignment
1 Red 9 NC
2 Green 10 GND-Sync
3 Blue 11 GND
4 GND 12 DDC SDA
DDC 5V Standby
5
/Cable connection check
6 GND-Red 14 V Sync
7 GND-Green 15 DDC SCL
8 GND-Blue
6.4 9pin D-Sub(Female) Connector : RS232C Input
13 H Sync
Pin Signal Assignment Pin Signal Assignment
1 RS232 ID 6 NC
2 RS232 RXD 7 NC
3 RS232 TXD 8 +5V Output
4 NC 9 NC
5 GND
6.5 9pin D-Sub(Male) Connector : RS232C Output
z This connector is used for chain connection with other Eagle monitor.
Document No. D&TQP0302-11(0) Revision No. 01 Page 10 of 22
Pin Signal Assignment Pin Signal Assignment
1 NC 6 NC
2 RS232 RXD 7 NC
3 RS232 TXD 8 NC
4 NC 9 NC
5 GND
6.6 15pin D-Sub(Male, 2row) Connector
Pin Signal Assignment Pin Signal Assignment
1 Speaker ID 1 9 Left Full Range +
2 Speaker ID 0
3 Center Tweeter + 11 Right Full Range +
4 Center Tweeter - 12 Right Full Range 5 Center woofer1 + 13 LMNT
6 Center woofer1 - 14 AMP Ground
7 Center woofer2 + 15 Speaker ID 2
8 Center woofer2 -
10 Left Full Range -
z This connection is optimized for TANDBERG’s DNAM AMP system, And DNAM Identify the
speaker ID so that output appropriate audio signal to match this monitor’s speaker module.*
z On this monitor the pin1(Speaker ID 1) must be connected to ground by using internal speaker
wiring.
Pin name LMNT Speaker ID 2 Speaker ID 1 Speaker ID 0
Set digit to 1 1 0 1
1 : must be floated
0 : must be tied to circuit ground
Document No. D&TQP0302-11(0) Revision No. 01 Page 11 of 22
6. Supported Timing
7.1 Standard Timing Chart
Resolution
Timing Item
Pixel Clock (MHz) 25.175 35.4375 40.000 49.500 65.000 74.250 74.250
Sync Polarity (H/V) N/N P/P P/P P/P N/N P/P P/P
Scanning Type Progressive Progressive Progressive Progressive Progressive Progressive Progressive
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms)
640x480
@60Hz
31.469
31.778
25.422
0.318
3.813
1.589
59.940
16.683
15.253
0.064
0.064
0.794
800x600
@50Hz
31.500
31.746
22.575
1.129
3.612
4.430
50.000
20.000
19.048
0.032
0.127
0.794
800x600
@60Hz
37.879
26.400
20.000
1.000
3.200
2.200
60.317
16.579
15.840
0.026
0.106
0.626
800x600
@75Hz
46.875
21.333
16.162
0.323
1.616
3.232
75.000
13.333
12.800
0.021
0.064
0.488
1024x768
@60Hz
48.363
20.677
15.754
0.369
2.092
2.462
60.004
16.666
15.880
0.062
0.124
0.600
1280x720
@50Hz
37.500
26.667
17.239
5.926
0.539
2.963
50.000
20.000
19.200
0.133
0.133
0.533
1280x720
@60Hz
45.000
22.222
17.239
1.481
0.539
2.963
60.000
16.666
16.000
0.111
0.111
0.444
Resolution
Timing Item
Pixel Clock (MHz) 148.500 148.500 108.00 79.500 85.500 87.750 121.751
Sync Polarity (H/V) P/P P/P P/P N/P P/P N/P N/P
Scanning Type Progressive Progressive Progressive Progressive Progressive Progressive Progressive
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms)
1280x720
@100Hz
75.000
13.333
8.620
2.963
0.269
1.481
100.000
10.000
9.600
0.066
0.067
0.267
1280x720
@120Hz
90.000
11. 111
8.620
0.741
0.269
1.481
120.000
8.333
8.000
0.055
0.056
0.222
1280x1024
@60Hz
63.981
15.630
11.852
0.444
1.037
2.296
60.020
16.661
16.005
0.016
0.047
0.594
1280x768
@60Hz
47.776
20.931
16.101
0.805
1.610
2.415
59.870
16.703
16.075
0.063
0.147
0.419
1360x768
@60Hz
47.712
20.959
15.906
0.749
1.310
2.994
60.015
16.662
16.097
0.063
0.126
0.377
1366x768
@60Hz
48.320
20.695
15.567
0.661
0.912
3.556
59.803
16.722
15.894
0.041
0.248
0.538
1400x1050
@60Hz
65.317
15.309
11.499
0.607
1.240
1.963
59.979
16.672
16.075
0.046
0.061
0.490
Resolution
Timing Item
Pixel Clock (MHz) 119.000 162.000 74.250 74.250 74.250 148.5 148.500
Sync Polarity (H/V) P/N P/P P/P P/P P/P P/P
Scanning Type Progressive Progressive Progressive Progressive Progressive Progressive Progressive
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms)
1680x1050
@60Hz
64.674
15.462
14.118
0.403
0.269
0.672
59.883
16.699
16.235
0.031
0.093
0.340
1600x1200
@60Hz
75.000
13.333
9.877
0.395
1.185
1.877
60.000
16.667
16.000
0.013
0.040
0.613
1920x1080
@24Hz
27.000
37.037
25.859
8.592
0.593
1.993
24.000
41.666
40.000
0.148
0.185
1.333
1920x1080
@25Hz
28.125
35.555
25.859
7.110
0.593
1.993
25.000
40.000
38.400
0.142
0.178
1.280
1920x1080
@30Hz
33.750
29.629
25.859
1.184
0.593
1.993
30.000
33.333
32.000
0.116
0.148
1.067
1920x1080
@48Hz
52.000
48.000
1920x1080
@50Hz
56.250
17.777
12.929
3.555
0.296
0.997
50.000
20.000
19.200
0.071
0.089
0.640
Document No. D&TQP0302-11(0) Revision No. 01 Page 12 of 22
Resolution
Timing Item
Pixel Clock (MHz) 148.500 154.000
Sync Polarity (H/V) P/P P/N
Scanning Type Progressive Progressive
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms)
1920x1080
@60Hz
67.500
14.814
12.929
0.592
0.296
0.997
60.000
16.666
16.000
0.059
0.074
0.533
1920x1200
@60Hz
74.038
13.506
12.468
0.312
0.208
0.519
59.950
16.681
16.208
0.041
0.081
0.351
Document No. D&TQP0302-11(0) Revision No. 01 Page 13 of 22
7. User control function
8.1 User Controls
We will not provide remote controller, because no need to control the OSD function normally, but
will provide it for service engineer to check the RS232C function easily.
Following is the description how you can adjust or change the OSD function
Function name Operation RS232C command from
external controller
POWER • Monitor power on and off @@1KESPWR
MENU • With OSD deactivated, Activated to OSD menu
@@1KESMNU
• With OSD activated, Exit from main menu or sub menu.
SOURCE • With OSD deactivated, you can see the kind of displayed
@@1KESSRC
source on right under of the screen.
UP • With OSD deactivated, Hot key of the brightness control
@@1KESUPK
and increases the brightness.
• With OSD activated, move the cursor upward.
DOWN • With OSD deactivated, Hot key of the brightness control
@@1KESDWN
and decreases the brightness.
• With OSD activated, move the cursor downward
PLUS • With OSD deactivated, Hot key of the contrast control
@@1KESPLS
and increases the contrast.
• With OSD activated, enter sub menu and increases the
adjustment of the selected
MINUS • With OSD deactivated, Hot key of the contrast control
@@1KESMNS
and decreases the contrast.
• With OSD activated, decreases the adjustment of the
selected function.
SET • With OSD activated, Enter sub menu and change each sub
@@1KESSET
menu’s item
rd
z 3
character “1” of the RS232C command is the unit ID, so this can be changed according to
unit ID.
Document No. D&TQP0302-11(0) Revision No. 01 Page 14 of 22
8. Special Consideration
9.1 All the supported timing modes (includes LCD Panel mode) are described in chapter8.
(Optimized with TANDBERG’s requirement signal timing)
9.2 This model have plug & play feature of DDC 1, DDC2B. This function is operating when the
monitor is connected to a system compatible with VESA DDC standard.
The DDC data structure is based on VESA DDC 1.3 standard
9.3 You can adjust and change the several function without buttons, by using RS232C serial
communication protocol through 9pin D-Sub (Female) connector.
(Refer to RS232C serial interface protocol)
9.4 RS232C chain connection with several monitor is available through RS232C IN/OUT connector.
(ex, TANDBERG’s T3 system, Max 9 monitor)
So you can adjust and change the several monitor individually or at the same time.
9. Applicable Regulations
:The products described in this specification must meet all applicable safety and regulatory
requirements as listed in this chapter.
10.1 Approvals-Europe(CE Mark)
Type Requirement
CE Mark All Products must have CE mark
LVD Directive
73/23/EEC
Standards for LVD:
IEC/EN 60950-1 2
nd
ed
CB according to IEC60950-1 incl all the different nation deviations.
Special requirements.
• Ambient temperature 40℃
• CI. 5. 1 Touch current
Max 0.5mA touch current with switch “ON” and “OFF” position.
• Approved to 3,000 meter altitude above sea level.
EMC Directive
89/336/EEC
EN 55022 : 2005 (Class B)
EN 55024 : 1998 Incl A1/A2
EN 61000-3-2 : 2000
EN 61000-3-3 : 1995 Incl A1
Testing:
All testing must be performed in accredited test laboratory
EMC testing must be performed in laboratory appointed as competent body
according to the EMC directive
RoHS Directive Product must comply with the European RoHS Directive 2002/95/EC
Signed declarations or test reports is accepted to document compliance.
10.2 Approvals-North America(USA/Canada : UL, FCC Mark)
Type Requirement
Product must be tested and approved according to relevant standard Electrical Safety
CSA 60950-1-07 2
nd
ed / UL 60950-1 2nd ed
Approval agency must be accredited as an NRTL
EMC EMC Requirements according to FCC15B (Class B)
Document No. D&TQP0302-11(0) Revision No. 01 Page 15 of 22
10. Entire system block diagram
Document No. D&TQP0302-11(0) Revision No. 01 Page 16 of 22
11. Mechanical and printing Specifications
This monitor is used for TANDBERG’s video conferencing system ‘EAGLE’.
Following dimension and outward sharp is designed by TANDBERG originally.
16.1 Outward drawing and Weight
Outward Size 2412 X 170 X 867 mm
Weight Max 130Kg
16.2 Product label
16.2.1 Brand Logo : TANDBERG
16.2.2 Model No : FS-S5202C
16.2.3 Rating Label (This may vary based on the TANDBERG's request, and the changed
contents of the Rating Label shall not be specified in this specification.)
A. Location : on the top module (Refer to the following picture)
B. Tilt : Shall not be tilted more than 1mm
C. Size : 40 x 102 mm (R0.5 x 4edge)
D. Material : Enumudeurong (Polyester film)
E. Base Color : Black
F. Printing Color : PMS877(Silver)
G. Description:
Document No. D&TQP0302-11(0) Revision No. 01 Page 17 of 22
Rev: 1
16.2.4 Product’s barcode label and Serial number structure
A. Location : On the product label
B. Tilt : Shall not be tilted more than 1mm
C. Size : 70 x 11mm
D. Material : Art paper
E. Base Color : White
F. Printing Color : Black
G. Description:
Serial No digit Item Initial
1 D This mean D&T Inc
2 9 Build year (7:2007, 8:2008, 9:2009~)
3 A Build month(A: January, B: February, ~L: December)
4 E Model (A : FS-L4201C, B: FS-S5201C, C: FS-P6501C, D: FS-
L4205C, E : FS-S5202C....)
5~8 0001 Serial Number (0001~9999)
Manufactured digit Item Initial
1~4 2009 Build year
5~6 01 Build month(01:January, 02:February, ~12: December)
Document No. D&TQP0302-11(0) Revision No. 01 Page 18 of 22
16.3 Packing Specification (Full set 1unit)
16.3 1 Dimension
Width Depth Height
Carton box
(Outside, Full set 1 unit)
1500mm 1100mm 1240mm
16.3.2 Packing Weight & Volume
Packing Weight(Max) Volume
kg lbs m
3
3
ft
170 375 2.05 72.26
Document No. D&TQP0302-11(0) Revision No. 01 Page 19 of 22
16.3.3 Cushion and inside view
Document No. D&TQP0302-11(0) Revision No. 01 Page 20 of 22
16.3.4 BOX label
A. Location : On the 2 narrow side of carton box (Refer to the following picture)
B. Tilt : Shall not be tilted more than 3mm
C. Size : 104 x 127mm
D. Material : Art paper
E. Base Color : White
F.
Description:
G. Barcode structure(when we read the barcode by reader: 0100000000117336240P21D9AE0001)
*The barcode is in accordance with UCC/EAN128 format*
Readied digit Item Initial
1~2 01 First reference
3~10 00000000 Supplementary 8 digits
11~16 117336 TANDBERG’s item number
17~19 240 Second reference
20 P Variant
21~22 21 Third reference
23 D This mean D&T Inc
24 9 Build year (7:2007, 8:2008,~)
Same as product’s
barcode digits
25 A Build month(A: January, B: February, ~L: December)
26 E Model (A : FS-S5202C, …)
27~30 0001 Serial number (0001~9999)
Document No. D&TQP0302-11(0) Revision No. 01 Page 21 of 22
16.5 Container loading
16.5.1 In case of 20ft container
: 6 pallets= 18units
16.5.2 In case of 40ft container
: 13 pallets= 39units
Document No. D&TQP0302-11(0) Revision No. 01 Page 22 of 22
Loading...