D and T FS L2401D User Manual

MEDIC

MEDIC

AL LCD MONIT

AL LCD MONIT

OR

OR

USER'S GUIDE

FS-L2401D(

FS-L2401D(

24" )

24" )

English - 1

Symbol Definitions 2
Safety Instructions 4
Caution 7
FCC Information 10
Parts 12
Connector 13
Mechanical Product Drawing 14
Control 15
Power mangement 18
Adjust OSD Menu 19
Stansard Signal table 22
Signal connector Pin Assignments 23
Specification 26

Table of Contents

English - 32 - English

Symbol Definitions

The following symbols appear on the product. its labeling, or the
product packing. Each symbol carries a special definition, as
defined below

Dangerous : High Voltage.

Consult accompanying documents.

Direct Current.

lndicates protective earth ground.

DC Power control switch.

Serial Number.

Top-Bottom.

Fragile.

Maximum Stacking.

Indicats proof of conformity to applicable European
Econmic Community Council directives and to har­monzed standards published in the official journal of the
European Communities.

Medical Equipment is in accordance with UL 60601-1
and CAN/CSA C22.2 No.601.1 in regards to electric
shock, fire hazards, and mechanical hazards.

Tested to comply with FCC Class B standards.

Degrees of protection against the ingress of water.

This symbol indicates that the waste of electronic
equipment must not be disposed as unsorted municipal
waste and must be collected separately. Please contact
the manufacturer or other authorized disposal company
to decommission your equipement.

Do not get wet.

Tested to comply with VCCI Class B standards.

Tested to comply with CCC standards.

English - 54 - English

Safety Instructions

On Safety

1.Before connecting the AC power cord to the DC adapter outlet
make sure the voltage designation of the DC adapter corresponds
to the local electrical supply.

2.Never insert anything metallic into the cabinet openings of the
Liquid Crystal Display(LCD) monitor. doing so may create the
danger of electric shock.

3.To reduce the risk of electric shock, do not remove cover.
No user-serviceable parts inside. Only a qualified technician
should open the case of the LCD monitor.

4.Never use your LCD monitor if the power cord has been
damaged. Do not allow anything to rst on the power cord, and
keep the cord away from areas where people can trip over it.

5.Be sure to hold the plug, not the cord,when disconnecting the
LCD monitor from am electric socket.

6.Unplug your LCD monitor when it is going to be left unused for
an extended period of time.

7.Unplug your LCD monitor from the AC outlet before any service.

8.if your LCD monitor does not operate normally-in particular, if
there are any unusual sounds or smells coming from it-unplug it
immediately am authorized dealer or service center.

Warning

Do not to touch signal input,signal output or other connectors, and
the patient simultaneously.

Warning

Extrnal equipment intended for connection to signal input, signal
output or other connectors, shall comply with relevant IEC stan­dard(e.g.,IEC60950 for IT equipment and IEC60601 series for med­ical electrical equipment).
In addition, all such combination-system-shall comply with the stan­dard IEC 60601-1-1, safety requirements for medical electrical sys­tems. Any person who connectors has formed at system and is
therefore responsible for the system to comply with the require­ments of IEC 60601-1-1.
if,in doubt, contact qualified technician or your local representative.

On installation

1.Openings in the LCD monitor cabinet are provided for ventilation.
To prevent overheating, these openings should not be blocked or
covered. if you put the LCD monitor in a bookcase or some other
enclosed space, be sure to provide adequate ventilation.

2.Put your LCD monitor in a location with low humidity and
a minimum of dust.

3.Do not exepose the LCD monitor to rain or use it near water
(in kitchens, near swimming pools, etc.). if the LCD monitor
accidentally gets wet, unplug it and contact an authorized dealer
immediately.You can clean the LCD monitor with a damp cloth if
necessary, but be sure to unplug the LCD monitor first.

5.Locate your LCD monitor near an easily accessible AC outlet.

6.High temperature can cause problems. Don't use your LCD
monitor in direct sunlight and keep it away from heaters, stoves,
fireplaces, and sources of heat.

English - 7

.

This symbol alerts the user that important literature
concerning the operation of this unit has been included.
Therefore, it should be read carefully in order to avoid
potential problems.

This symbol warms user that un-insulated voltage within
the unit the may have sufficient magnitude to cause
electrical shock. Therefore, it is dangerous to make
contact with any part inside the unit. To reduce the risk of
electric shock, DO NOT

remove cover (or back). There
are no user serviceable parts inside. Refer servicing to
qualified service personal.

To prevent fire or shock hazards, do not expose this unit to rain or
moisture. Also, do not use this unit's polarized plug with an
extension cord receptacle or other outlets unless the prongs can
be fully inserted. The display is designed to meet the medical
safety requirements for a patient vicinity device. This device may
not be used in connection with life support equipment.

CAUTION

Underwriters Laboratories (UL) Classification:
UL safety Compliance:

This LCD monitor is U.L. Classified WITH RESPECT TO
ELECTRIC SHOCK, FIRE AND MECHANICAL
HAZARDS ONLY IN ACCORDANCE WITH UL 60601­1/CAH/CSA C22.2 NO. 601.1

6 - English

Environmental Conditions for transport and Storage

- Temperature range within -30°C to 85°C

- Relative humidity range 5% to 95%
Atrnospheric pressure range within 500 to 1060hPs.