Suggested Equipment
Motor: MM1904 2500
ESC: 20A
Battery: 3s 800-1500mAh
Propeller: 6inch
Servos: 9g*4
Radio≥4CH
Speci�ication
Wingspan: 1000mm
Length: 650 mm
Flying Weight≈320g
Accessories include
Power System（Optional）
Preparation Tool
How to Assemble
A1
A1
A2
A3
A4
A5
A9
A6
A7
B1
B2
B3 B4
B5
B6
C
D
E
G
H
F
A8 A8
A1
B4
B1
1.Take down the B1,B4,and past onto the fuselage A1,pls
notice the curve and cut;Assemble the other side in same
way and paste with foamy glue.
2.Take down the B6 and paste onto the B1,paste the both
sides of the fuselage with 502 glue.
3.Paste the cut in the middle of the fuselage with foamy
glue,and do the same the other side.
B6
pls notice the curve and cut
Mini Shark
Instruction Manual
EPP Airplane
A1-A9:EPP parts B1-B6:Wood components
C:Round pole D:Fiberglass connection for wing
E:Rubber band F:Steel wire linkage G:Propeller
H:EZ Connetor
Mini Shark
Instruction Manual
EPP Airplane
4.Paste the fuselage bottom A2 with foamy glue,pls notice
the head must be bent as picture shown;Do not paste the
cover of cabin.
A2
5.Paste the A6 and A9 onto the upper of the fuselage with
foamy glue.
6.Paste the vertical tail A3 and A5 with foamy glue.
7.Paste the horizontal tail A4 and A7 with foamy glue.
A5
A3
A6
A9
A4
A7
８.Install the motor onto the motor mount B2 and fasten
with screws;Install the prop saver and propeller.
９.Paste the fins onto the fuselage,install the motor at the
position with foamy glue,pull the motor wires inside of the
fuselage.Connect the motor with ESC,and put the ESC
inside of the fuselage.
B2
12.Connect the two wings together with V-shape fiberglass
piece D,and paste together with foamy glue,make sure the
wing with V-shape.
10.Assemble and glue the servo mount with 502,install the
servo onto the servo mount,pls notice the servo arm at
opposite direction;Install the EZ-connector onto the servo
arm.
11.Cut a hole at the bottom of the cabin,glue the servo
mount inside of the fuselage.
A2
Mini Shark
Instruction Manual
EPP Airplane
13.Paste the servo in the preserved hole with foamy
glue,and assemble the servo horn;Assemble the other side
in same way.
14.Insert and glue the servo wires into the slot.
15.Insert the wing into the fuselage and put the servo wires
inside of the fuselage.
16.Insert the round pole in the preserved hole on the
fuselage,adjust the wing in the middle position,finally
fasten the wing with rubber band.
17.Install the servo horn onto the rudder and elevator as
picture shown below,insert the steel wire linkage through
the tail into the fuselage,connect the Z-shape end onto the
servo horn.
18.Connect the other end of the linkage with servo arm
EZ-connector inside the fuselage.
19.Install the servo horn on the aileron,fasten the Z-shape
end linkage onto the servo horn,connect the other end onto
the EZ-connetor;Assemble in same way the other side.
Mini Shark
Instruction Manual
EPP Airplane
20. Installthe power system and adjust the C.G.
Battery position
C.G about 80mm from
the leading edge
finish
C.G
Loading...