Danalock V3 US
www.danalock.com
Table of content
0. Parts involved 5
1. Download the Danalock app 6
2. Get your tools together 7
3. Check door alignment 8
4. Secure outside keyhole 9
5. Remove inside thumb-turn 10
6. Select a backplate 11
7. Remove the paper from the stickers 12
8. Fasten backplate 13
9. Select tailpiece adapter 14
10. Insert adapter into Danalock 15
11. Fit and fasten Danalock 16
12. Align the platemarks 17
13. Fasten the Danalock 18
14. Activate batteries 19
15. Before completing the setup 20
16. Open the Danalock app 21
17. Dismount instructions 22
18. LED-Signals 23
19. Conguring the Danalock V3 with click-commands 24
0. Parts involved
3
1. Download the Danalock app
Go to Google Play or App Store and download the Danalock app.
When the app is installed you create a user prole by pressing the
blue ring. You will use this prole each time you sign into the app.
You will need to nish set-
ting the Danalock up in the
app after mounting it on
the door.
u
n
e
M
g
o
L
rs
e
s
u
k
c
o
L
k
c
lo
d
d
A
s
g
in
tt
e
S
4
2. Get your tools together
To install the Danalock, you’ll need a Phillips screw dri ver and tape,
preferably masking tape. Should you need to remove or readjust
the lock, a pen tip or paper clip will be needed.
5
3. Check door alignment
Ensure that your door is properly aligned before beginning installation.
You should be able to lock
your door without pushing,
pulling, or lifting the door.
Thumb-turn
must move and
lock smoothly.
6
4. Secure outside keyhole
Before removing your existing lock, use tape to secure the outside
keyhole. This will keep it in place as you remove the screws on the
inside.
7
5. Remove inside thumb-turn
Remove the inside thumb-turn, leaving just the deadbolt and tailpiece remaining. Set aside the screws. You’ll reinstall them in step 8.
8
6. Select a backplate
Find the backplate that matches the brand of your existing lock.
9
7. Remove the paper from the stickers
On the backside of the backplate you’ll nd three stickers.
Remove the paper from the stickers.
10
8. Fasten backplate
Fasten the backplate where the thumb-turn was using the two
origin al screws, with the arrow on the label pointing up.
The notches on the backplate must be
facing out with the tailpiece centered
exactly in the middle hole.
Original screws
11
9. Select tailpiece adapter
Select the tailpiece adapter that matches the shape of your existing
lock’s tailpiece.
Baldwin
Baldwin
Kwikset
Schlage
Depends on the length
of your tailpiece.
Emtek
Omnia
Weiser
Weslock
12
10. Insert adapter into Danalock
Insert the selected tailpiece adapter into your Danalock and press
until it clicks in place.
Click!
13
11. Fit and fasten Danalock
Fit the Danalock onto the backplate with the battery cover facing down, the tailpiece sliding into the adapter and the backplate
notches into the back of the lock.
Tailpiece
Backplate
14
Battery cover
facing down
12. Align the platemarks
Find the small marking at the edge of the backplate and align it with
the hole in the cover ring surrounding the Danalock. Now you are
sure to hit the notches on the backplate with the Danalock.
15
13. Fasten the Danalock
Turn the Danalock clockwise until it clicks to fasten it to the backplate.
NOTE: If you need to unfasten and retry, see “Uninstall instructions”
on p. 22.
Click!
16
14. Activate batteries
Pull out the plastic tab to activate the batteries. A light will ash to
conrm the Danalock is ready.
Note: If the batteries are disconnected, you will have to re-calibrate
the Danalock.
17
15. Before completing the setup
Your Danalock is now attached to the door.
Leave the door open, so
the lock isn’t inuenced
when calibrated.
18
16. Open the Danalock app
Open the Danalock app you downloaded at the start. When you
have logged in you will see your empty keychain. Press ”Add lock” at
the bottom of the screen.
A guide will now lead you
through the installation
and conguration of your
Danalock.
keys
no
ve
ha
e
tt
your
in
p
g
ressing
lock”
below
s
lock
rst
fi
the
icon
u
n
e
M
g
o
L
rs
e
s
u
k
c
o
L
k
c
lo
d
d
A
19
You
Add
by
”Add
S
17. Dismount instructions
If at any time you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press
while turning the lock counter- clockwise until the lock releases.
This will not reset the lock
or disconnect it from your
account, but the lock may
need to be re-calibrated
if fastened to your door
again.
20
18. LED-Signals
A LED light on the Danalock indicates the status of several opera-
tions with dierent colours:
LED-Mode LED color Status indication
Constant red till light nishes Lock has successfully locked
Constant green till light nishes Lock has successfully unlocked
Constant white for 3 seconds Power on. Batteries are activated
Red light ashes every 5 minutes Critical battery level
Constant purple Firmware is being updated
Blue light ashes Settings are changed/saved
21
19. Conguring the Danalock V3 with click-commands
You can congure the Danalock via the button found in the small
hole on the top of the lock. When you click through settings, the
LED will change color according to the scheme on the next page.
When you get to the setting you want to change, wait for 5 seconds
and the Danalock will react to your command. If you make a wrong
number of clicks, just stop at a number of clicks where the LED
doesn’t light up and wait for 5 seconds. The LED will ash red to indicate that it has timed out.
22
Clicks Color Activity
1 Green Inclusion mode
This mode is used to in- or exclude your Danalock with a Z-Wave or Zigbee gateway.
When the Danalock blinks green it is in ex/inclusion mode and you have 30 seconds to
pair the Danalock with a gateway.
2 Yellow Manual calibration
Turn the Danalock to the desired unlocked position. Start the calibration with the
click command and wait for the LED to start blinking yellow. Turn the Danalock to the
desired locked position while the LED blinks and click the button once to save the
locked position. If the lock doesn’t receive a response from you within 30 seconds the
calibration will be canceled.
3 White Auto calibration
Turn the Danalock to unlocked position and lift the handle if needed. Leave the door
open while the Danalock auto calibrates. Start the auto calibration with the click
command. The Danalock will blink white while auto calibrating.
7 Cancel
10 Red Reset user settings
This action deletes all user settings on the Danalock. The Danalock responds by
blinking red.
23
Danalock International ApS
Gammel Stillingvej 427C
8462 Harlev, DK
+45 4242 8122
info@danalock.com
www.danalock.com
DV3-US-EN-2018/09/13
Loading...