Danaher Controls DX100 Data Sheet

EAGLE SIGNAL brand

VEEDER-ROOT brand

Electronic Totalizing Counters

DX100 Time/Count Totalizer

Totalizes count or elapsed time… convienient surface mount in relay socket or panel mount

RECOGNIZED

The DX100 is a solid state time/count totalizer. Its features include:

■ Housed in 1/16 DIN molded NORYL

■ 0.5 inch high, 4 1/2 digit liquid crystal display

■ Annunciators on front panel indicate time/count operating mode and

time range

■ 6 time ranges from 1999.9 sec. to 19999 hrs. and count range of

19999 counts

■ Surface mounted using standard square base relay socket

(accessories available for fixed or plug-in panel mounting)

case

OPERATION

Timing is referenced to the service line frequency. The line frequency is counted and internal divider networks determine one of six available time ranges.

Two count modes are available and determined by external wiring. Mode 1: Line voltage is applied to the count input. The count is registered when the line voltage is removed from the count input (trailing edge). Mode 2: Contact closure across the internal count circuit registers a count (leading edge).

All units have remote reset capability through external wiring.

NOTE: The cable from the totalizer to the remote reset switch must be a twisted pair with a maximum length of 5 feet.

The 02 option features a manual reset push-button on the front of the unit in addition to the remote reset capability.

The DX100 Totalizer has an internal, replaceable battery. The charge on the battery is maintained at a constant level by a trickle charge circuit. A fully charged battery will maintain memory and readout for a minimum of 650 hours with power disconnected. It is recommended that the battery be replaced every two years. Initial slow response of the LCD readout indicates a low battery charge. To charge battery to full capability, apply line voltage to the unit for 48 hours.

SPECIFICATIONS

Time/Count Ranges:

Sym. Time

Repeatability: Timing is based on service line frequency Count Accuracy: 100% Count Speed: 2500 per min. with voltage application:

8 ms "ON" 16 ms "OFF"

5000 per min. with switch closure: 4 ms "ON" 8 ms "OFF"

Reset Time: 10 ms Cycle Progress: 4 1/2 digit liquid crystal display, .5" high (12.7 mm) Voltage/Frequency: 120 VAC, 60 Hz (Can be field modified for

50 Hz operation)

Burden: 120 VAC, 1.2 Watts

120 VDC, 1.2 Watts (Counter only)

Current Required to Energize Count Line: 16.4 microamperes Power Interruption: Line voltage interruptions will not reset timer or

counter. Battery life is a minimum of 2 years (field-replaceable).

Temperature Range: 32° to 140°F (0° to 60°C) Transient Voltage Immunity: Performance unaffected by 50

microseconds, 600 V peak transients superimposed on line input.

Vibration: Unaffected by 2.5G sinusoidal vibration magnitudes in both

directions of three perpendicular mounting axes imposed from 20 to 900 Hz

Approvals: UL Recognition E96337

Range

19999 Ct.

1999.9 Sec.

19999 Sec.

1999.9 Min.

19999 Min.

1999.9 Hr.

19999 Hr.

Factory Programmed

VEEDER-ROOT • EAGLE SIGNAL • DYNAPAR 1.13

VEEDER-ROOT brand

Electronic Totalizing Counters

ACCESSORIES

E L E C T R O N

Model No. Description

T O

DZ100-51 Bezel Kit for panel mounting

DZ100-52 Strain Relief Kit

DZ100-54 Plug-In Housing for panel mounting units

DZ100-56 Latch and Latch Release Kit for surface mounting

60SR3BO5 Square Base Relay Socket

I N G

MOUNTING

3.250

(82.55)

0.218 (5.54)

2.0 Max (50.8)

Panel Mount

3.810

(96.77)

Bezel

Add For

Each

Additional

Unit

Panel Cutout +.000 –.040

3.622 (92.0)

1.922 (48.8)

1.722 (44.0)

(17.45)

0.687

Up to 0.375

Panel

Thickness

1.922 (48.8)

0.218 (5.54)

1.457

(37.00)

Surface Mount

2.992

(75.99)

0.165 Typ (4.19)

TOTALIZER

Eagle Signal brand

3.546 (90.0)

(24.99)

(82.55)

0.079 (2.00)

1.417 (35.99)

Plug-In Mount

3.812

0.984

3.860

3.250

1.693

(43.00)

1.656 (42)

(98.04)

Up to 0.375

Panel Thickness

(9.53)

0.980

(24.82)

0.270 (6.85)

NOTE: PANELS THICKER THAN .140" REQUIRE ENLARGEMENT OF CORNERS TO ALLOW POSITIONING OF CORNER MOUNTING BRACKETS

(96.82)

4.062

(103.17)

Panel Cutout +.030 –.060

3.850

(97.79)

1.950

(49.53)

2.188

(55.57)

ORDERING INFORMATION

TIME RANGE

Sym. Description

19999 Ct.

1999.9 Sec.

19999 Sec.

1999.9 Min.

19999 Min.

1999.9 Hr.

19999 Hr.

19999 Ct.

1999.9 Sec.

19999 Sec.

VEEDER-ROOT • EAGLE SIGNAL • DYNAPAR1.14

Annunciator

CTS

SEC and Decimal

SEC

MIN and Decimal

MIN

HR and Decimal

Annunciators are not

programmed. All

annunciators are displayed.

DX1 01 A6 02

VOLTAGE & FREQUENCY

Sym. Description

120 VAC, 60 Hz*

*Unit can be modified to 50 Hz operation.

FEATURES

Sym. Description

Standard Remote Reset ONLY

Reset Pushbutton on Front Panel

(May be wired for Remote Reset)

Replacement Battery: Part No: PBB-9