Dallas Semiconductor DS2433S, DS2433-T-R, DS2433, DS2433X, DS2433S-T-R Datasheet

1 of 19 062299

FEATURES

§ 4096 bits Electrically Erasable Programmable

Read Only Memory (EEPROM)

§ Unique, factory-lasered and tested 64-bit

registration number (8-bit family code + 48­bit serial number + 8-bit CRC tester) assures
absolute identity because no two parts are
alike

§ Built-in multidrop controller ensures

compatibility with other MicroLAN products

§ Memory partitioned into sixteen 256-bit pages

for packetizing data

§ 256-bit scratchpad with strict read/write

protocols ensures integrity of data transfer

§ Reduces control, address, data and power to a

single data pin

§ Directly connects to a single port pin of a

microprocessor and communicates at up to

16.3k bits per second

§ Overdrive mode boosts communication speed

to 142k bits per second

§ 8-bit family code specifies DS2433

communication requirements to reader

§ Presence detector acknowledges when reader

first applies voltage

§ Low cost PR-35 or 8-pin SOIC surface mount

package

§ Reads and writes over a wide voltage range of

2.8V to 6.0V from -40°C to +85°C

PIN ASSIGNMENT

PIN DESCRIPTION

PR-35 SOIC

Pin 1 Ground NC
Pin 2 Data NC
Pin 3 NC Data
Pin 4 -- Ground
Pin 5-8 -- NC

ORDERING INFORMATION

DS2433 PR-35 package
DS2433S 8-pin SOIC package
DS2433T Tape & Reel version of DS2433
DS2433Y Tape & Reel version of DS2433S
DS2433X Chip Scale Pkg., Tape & Reel

SILICON LABEL DESCRIPTION

The DS2433 4K-bit 1-Wire EEPROM identifies and stores relevant information about the product to
which it is associated. This lot or product specific information can be accessed with minimal interface,
for example a single port pin of a microcontroller. The DS2433 consists of a factory-lasered registration
number that includes a unique 48-bit serial number, an 8-bit CRC, and an 8-bit Family Code (23h) plus
4096 bits of user-programmable EEPROM. The power to read and write the DS2433 is derived entirely

DS2433

4k-Bit 1-WireTM EEPROM

www.dalsemi.com

NCNCDATA

GND

234

8

7

651

8-PIN SOIC (208 MIL)

12332

1

PR-35

BOTTOM VIEW

DS2433

2 of 19

from the 1-Wire communication line. The memory is organized as sixteen pages of 256 bits each. The
scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to the
scratchpad where it may be read back for verification. A copy scratchpad command will then transfer the
data to memory. This process insures data integrity when modifying the memory. The 64-bit registration
number provides a guaranteed unique identity which allows for absolute traceability and acts as node
address if multiple DS2433 are connected in parallel to form a local network. Data is transferred serially
via the 1-Wire protocol which requires only a single data lead and a ground return. The PR-35 and SOIC
packages provide a compact enclosure that allows standard assembly equipment to handle the device
easily for attachment to printed circuit boards or wiring. Typical applications include storage of
calibration constants, board identification and product revision status.

OVERVIEW

The block diagram in Figure 1 shows the relationships between the major control and memory sections of
the DS2433. The DS2433 has three main data components: 1) 64-bit lasered ROM, 2) 256-bit
scratchpad, and 3) 4096-bit EEPROM. The hierarchical structure of the 1-Wire protocol is shown in
Figure 2. The bus master must first provide one of the six ROM Function Commands, 1) Read ROM, 2)
Match ROM, 3) Search ROM, 4) Skip ROM, 5) Overdrive-Skip ROM or 6) Overdrive-Match ROM.
Upon completion of an overdrive ROM command byte executed at standard speed, the device will enter
Overdrive mode where all subsequent communication occurs at a higher speed. The protocol required for
these ROM function commands is described in Figure 9. After a ROM function command is successfully
executed, the memory functions become accessible and the master may provide any one of the four
memory function commands. The protocol for these memory function commands is described in Figure

7. All data is read and written least significant bit first.

PARASITE POWER

The block diagram (Figure 1) shows the parasite-powered circuitry. This circuitry “steals” power
whenever the I/O input is high. I/O will provide sufficient power as long as the specified timing and
voltage requirements are met.

DS2433 BLOCK DIAGRAM Figure 1

DS2433

3 of 19

64-BIT LASERED ROM

Each DS2433 contains a unique ROM code that is 64 bits long. The first eight bits are a 1-Wire family
code. The next 48 bits are a unique serial number. The last eight bits are a CRC of the first 56 bits. (See
Figure 3.) The 1-Wire CRC is generated using a polynomial generator consisting of a shift register and
XOR gates as shown in Figure 4. The polynomial is X8+ X5+ X4+ 1. Additional information about the
Dallas 1-Wire Cyclic Redundancy Check is available in the Book of DS19xx iButton Standards.

The shift register bits are initialized to zero. Then starting with the least significant bit of the family code,
one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial number
is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC
value. Shifting in the eight bits of CRC should return the shift register to all zeros.

MEMORY

The memory map in Figure 5 shows a 32-byte page called the scratchpad and additional 32-byte pages
called memory. The DS2433 contains pages 0 through 15 which make up the 4096-bit EEPROM. The
scratch-pad is an additional page that acts as a buffer when writing to memory.

ADDRESS REGISTERS AND TRANSFER STATUS

Because of the serial data transfer, the DS2433 employs three address registers, called TA1, TA2 and E/S
(Figure 6). Registers TA1 and TA2 must be loaded with the target address to which the data will be
written or from which data will be sent to the master upon a Read command. Register E/S acts like a byte
counter and Transfer Status register. It is used to verify data integrity with write commands. Therefore,
the master only has read access to this register. The lower five bits of the E/S register indicate the address
of the last byte that has been written to the scratchpad. This address is called Ending Offset. Bit 5 of the
E/S register, called PF, is set if the number of data bits sent by the master is not an integer multiple of 8 or
if the data in the scratchpad is not valid due to a loss of power. A valid write to the scratchpad will clear
the PF bit. Bit 6 has no function; it always reads 0. Note that the lowest five bits of the target address
also determine the address within the scratchpad, where intermediate storage of data will begin. This
address is called byte offset. If the target address (TA1) for a Write command is 03CH for example, then
the scratchpad will store incoming data beginning at the byte offset 1CH and will be full after only four
bytes. The corresponding ending offset in this example is 1FH. For best economy of speed and
efficiency, the target address for writing should point to the beginning of a new page, i.e., the byte offset
will be 0. Thus the full 32-byte capacity of the scratchpad is available, resulting also in the ending offset
of 1FH. However, it is possible to write one or several contiguous bytes somewhere within a page. The
ending offset together with the Partial Flag support the master checking the data integrity after a Write
command. The highest valued bit of the E/S register, called AA is valid only if the PF flag reads 0. If PF
is 0 and AA is 1, a copy has taken place. The AA bit is cleared when the device receives a write
scratchpad command.

WRITING WITH VERIFICATION

To write data to the DS2433, the scratchpad has to be used as intermediate storage. First the master
issues the Write Scratchpad command to specify the desired target address, followed by the data to be
written to the scratchpad. Under certain conditions (see Write Scratchpad command) the master will
receive an inverted CRC16 of the command, address and data at the end of the write scratchpad command
sequence. Knowing this CRC value, the master can compare it to the value it has calculated itself to
decide if the communication was successful and proceed to the Copy Scratchpad command. If the master
could not receive the CRC16, it has to send the Read Scratchpad command to read back the scratchpad to
verify data integrity. As preamble to the scratchpad data, the DS2433 repeats the target address TA1 and
TA2 and sends the contents of the E/S register. If the PF flag is set, data did not arrive correctly in the

DS2433

4 of 19

scratchpad or there was a loss of power since data was last written to the scratchpad. The master does not
need to continue reading; it can start a new trial to write data to the scratchpad. Similarly, a set AA flag
together with a cleared PF flag indicates that the Write command was not recognized by the device. If
everything went correctly, both flags are cleared and the ending offset indicates the address of the last
byte written to the scratchpad. Now the master can continue reading and verifying every data byte.
After the master has verified the data, it has to send the Copy Scratchpad command. This command must
be followed exactly by the data of the three address registers TA1, TA2 and E/S. The master may obtain
the contents of these registers by reading the scratchpad or derive it from the target address and the
amount of data to be written. As soon as the DS2433 has received these bytes correctly, it will copy the
data to the requested location beginning at the target address.

HIERARCHCAL STRUCTURE FOR 1-WIRE PROTOCOL Figure 2

64-BIT LASERED ROM Figure 3

MSB LSB

8-Bit CRC Code 48-Bit Serial Number 8-Bit Family Code (23h)

MSB LSB MSB LSB MSB LSB

1-WIRE CRC GENERATOR Figure 4

INPUT

DS2433

5 of 19

MEMORY FUNCTION COMMANDS

The “Memory Function Flow Chart” (Figure 7) describes the protocols necessary for accessing the
memory. An example follows the flowchart. The communication between master and DS2433 takes
place either at regular speed (default, OD = 0) or at Overdrive Speed (OD = 1). If not explicitly set into
the Overdrive Mode the DS2433 assumes regular speed.

WRITE SCRATCHPAD COMMAND [0FH]

After issuing the write scratchpad command, the master must first provide the 2-byte target address,
followed by the data to be written to the scratchpad. The data will be written to the scratchpad starting at
the byte offset (T4:T0). The ending offset (E4:E0) will be the byte offset at which the master stops
writing data. Only full data bytes are accepted. If the last data byte is incomplete its content will be
ignored and the partial byte flag PF will be set.

When executing the Write Scratchpad command the CRC generator inside the DS2433 (see Figure 12)
calculates a CRC over the entire data stream, starting at the command code and ending at the last data
byte sent by the master. This CRC is generated using the CRC16 polynomial by first clearing the CRC
generator and then shifting in the command code (0FH) of the Write Scratchpad command, the Target
Addresses TA1 and TA2 as supplied by the master and all the data bytes. The master may end the Write
Scratchpad command at any time. However, if the ending offset is 11111b, the master may send 16 read
time slots and will receive the CRC generated by the DS2433.

The memory address range of the DS2433 is 0000H to 01FFH. If the bus master sends a target address
higher than this, the internal circuitry of the chip will set the seven most significant address bits to zero as
they are shifted into the internal address register. The Read Scratchpad command will reveal the target
address as it will be used by the DS2433. The master will identify such address modifications by
comparing the target address read back to the target address transmitted. If the master does not read the
scratchpad, a subsequent copy scratchpad command will not work since the most significant bits of the
target address the master sends will not match the value the DS2433 expects.

READ SCRATCHPAD COMMAND [AAH]

This command is used to verify scratchpad data and target address. After issuing the read scratchpad
command, the master begins reading. The first two bytes will be the target address. The next byte will be
the ending offset/data status byte (E/S) followed by the scratchpad data beginning at the byte offset (T4:
T0). The master may read data until the end of the scratchpad after which the data read will be all logic
1’s.

COPY SCRATCHPAD [55H]

This command is used to copy data from the scratchpad to memory. After issuing the copy scratchpad
command, the master must provide a 3-byte authorization pattern which can be obtained by reading the
scratchpad for verification. This pattern must exactly match the data contained in the three address
registers (TA1, TA2, E/S, in that order). If the pattern matches, the AA (Authorization Accepted) flag
will be set and the copy will begin. Copy takes 5 ms maximum during which the voltage on the 1-Wire
bus must not fall below 2.8V. A pattern of alternating 1s and 0s will be received after the data has been
copied until a Reset Pulse is issued by the master.

The data to be copied is determined by the three address registers. The scratchpad data from the
beginning offset through the ending offset, will be copied to memory, starting at the target address.
Anywhere from 1 to 32 bytes may be copied to memory with this command.

DS2433

6 of 19

DS2433 MEMORY MAP Figure 5

ADDRESS REGISTER Figure 6

READ MEMORY [F0H]

The read memory command may be used to read the entire memory. After issuing the command, the
master must provide the 2-byte target address. After the two bytes, the master reads data beginning from
the target address and may continue until the end of memory, at which point logic 1’s will be read. It is
important to realize that the target address registers will contain the address provided. The ending
offset/data status byte is unaffected.

The hardware of the DS2433 provides a means to accomplish error-free writing to the memory section.
To safeguard reading data in the 1-Wire environment and to simultaneously speed up data transfers, it is
recommended to packetize data into data packets of the size of one memory page each. Such a packet
would typically store a 16-bit CRC with each page of data to insure rapid, error-free data transfers that
eliminate having to read a page multiple times to determine if the received data is correct or not. (See the
Book of DS19xx iButton Standards, Chapter 7 or Application Note 114 for the recommended file
structure.)

32-BIT INTERMEDIATE STORAGE SCRATCHPAD

32-BYTE FINAL STORAGE EEPROM

32-BYTE FINAL STORAGE EEPROM

FINAL STORAGE EEPROM

32-BYTE FINAL STORAGE EEPROM

ADDRESS

0000H TO

001FH

003FH

01DFH

01FFH

0020H TO

0040H TO

1FE0H TO

PAGE 0

PAGE 1

PAGE 2
TO PAGE 14

PAGE 15

T7 T6 T5 T4 T3 T2 T1 T0

T15

AA 1) PF E4 E3 E2 E1 E0

T14 T13 T12 T11 T10 T9 T8

TARGET ADDRESS (TA1)

TARGET ADDRESS (TA2)

ENDING ADDRESS WITH

DATA STATUS (E/S)

(READ ONLY)

1) THIS BIT WILL ALWAYS BE 0.