Da-Lite Wireline Advantage Instruction Manual

INSTRUCTION BOOK FOR

Wireline™ Advantage

®

Important Safety Instructions

Case Installation

When using your video equipment, basic safety precautions
should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so it will not be tripped over, pulled or contact
hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.

5. The use of an accesory attachement not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.

6. Do not allow children to play with ixed controls. Keep remote
controls away from children.

7. Frequently examine the installation for imbalance and signs of
wear or damage to cables. Do not use if repair or adjustment is
necessary.

Save These Instructions

1. The case provides multiple attachment points for bolts,
cables, or threaded rod. Page 4 shows threaded rod
installed. The variable position-mounting bracket may be
located anywhere along the length of the case. It is
recommended to keep the brackets spaced evenly enough
to distribute the weight of the screen. One mounting bracket
is required for every 4' of case length.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, screen assembly must be level

after installation.

3. Remove 2 screws to open junction box. Install electrical
connections that apply to your unit. Make sure to review the
wiring diagram for proper hook up. Replace junction box
cover and secure with 2 screws.

NOTE: Please Note: Motor Operator Projection Screen Model

WAD must be installed in accordance with the requirements
of the Local Building Codes, the Canadian Electrical Code
(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),
NFPA 70. An appropriate disconnect device shall be
provided as part of the building installation.

Tools Required for Installation

1/4" and 3/4“

Open Wrench or

Socket Driver

1/8“ Hex Key

(included)

Pre-Installation

1. Carefully unpack case from shipping crate.

2. Set aside the Installation Kit. Items inside will be used during
installation.

4. Remove the silver shipping brackets that attach the slat to
the screen case. Use the supplied 1/8" hex key to remove the
set screws and a 1/4" socket to remove the screws from the
slat bar.

5. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor,
the standard duty cycle is 2 minute 30 seconds on and 50
minutes of.

6. The screen comes set standard with 18" of wire drop out of
the case.

3. Make sure to recheck measurement of case for proper
installation clearance.

4. Remove any protective foam from case.

5. If necessary. adjust hanger brackets with a 3/4" open wrench
or socket driver.

2

Installation

Electrical

Junction Box

9 ⅛"

(Suggested) 1/2"
Threaded Rod
(Not Included)
Attached to
Mounting Bracket

Finished

Ceiling

11"

Self-Trimming
Flange

13 ⅛"

Variable Position

Mounting Brackets

11 ⁄"

12 ⁄"

Screen Roller

Self-Trimming
Flange

Access Door

Audience
Side

Electrical

Junction Box

3

Screen Adjustment

Surface travel is set to stop automatically with 18" of wire travel out of the case. Use the supplied radio frequency remote control to
make adjustments to the amount of travel.

More Screen Drop

1. Run screen in down direction until it reaches lower limit and

stops.

2. Press and hold both UP and DOWN arrows simultaneously until
screen jogs.

3. Run screen to new desired lower limit position by pressing
DOWN arrow on remote

Note: Motor will run in momentary contact mode while in this

procedure. If you go to far down you can press up and move
to the next step.

4. Press and MY (STOP) button until the screen jogs to conirm
new limit.

CAUTION: Do not adjust for more than 29' of cable drop.

ATTENTION! Ne pas régler plus de 884 centimètres de chute

de câble

Less Screen Drop

1. Run screen in down direction until it reaches lower limit and
stops.

2. Press and hold both UP and DOWN arrows simultaneously until
screen jogs.

3. Run screen to new desired lower limit position by pressing UP
arrow on remote.

Note: Motor will run in momentary contact mode while in this

procedure. If you go to far down you can press down and
move to the next step.

4. Press and MY (STOP) button until the screen jogs to conirm
new limit.

Note: The entire screen must be unrolled from the large roller

for proper tensioning.

Figure 1

4

120V Wiring Diagram

Power Input

120VAC / 60Hz

White (Common)

Black (Hot)

Green

(Ground)

Ground
Lug

240V Wiring Diagram

Power Input

220VAC / 50Hz

Blue (Common)

Brown (Hot)

Green/Yellow

(Ground)

Ground
Lug

5

Troubleshooting

Visit www.da-lite.com to ind installation and troubleshooting
tutorials. You will also ind a link to Live Chat for interactive
support.

Symptom Cause Solution

Incorrect line voltage.

Screen will not operate
and motor does not hum.

Screen will not operate
and motor does not hum.

Power at junction box.

Screen does not stop
at correct position.

Blown fuse. Replace fuse.

Tripped circuit breaker. Reset circuit breaker.

No power to junction.

Thermal overload tripped. Let motor cool down for 50 minutes. Try again.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Capacitor burned out. Replace motor assembly.

Limit switch out of adjustment. See Screen Adjustment section.

You can contact us by email at [e-mail] or by phone
at 800.622.3737 or 574.267.8101 with any additional
troubleshooting questions.

Verify 115125V (or 220240V). If insuicient voltage, rewire
incoming electric line.

Check above. Tighten all loose wire connections.
Correct any improper connections.

Squeaking, rubber end plug rubbing on motor. Center roller in case.

Noise.
NOTE: Screen will operate
with a low pitched hum.

Coasting. Defective brake. Replace motor assembly.

Fabric hangs crooked.

Grinding. Foreign object in screen
rubbing on roller or fabric.

Gear noise. Replace motor assembly.

Screen not installed properly. Check for level and plumb.

Fabric is damaged. Replace fabric.

Remove.

6

7

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the
factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at
3100 North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

A Milestone AV Technologies Brand

3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: [e-mail]
www.da-lite.com

DL–0620 (Rev. 1) 01.16
© 2016 Milestone AV Technologies LLC. Printed in U.S.A.

29355