Page 1
INSTRUCTION BOOK FOR
Tensioned Large
Cosmopolitan® Electrol
®
Page 2
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating
at least equal to that of the appliance should be used. Cords
rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of ire, electric shock, or
injury to persons.
Save These Instructions
2
Page 3
Installation
Carefully unpack screen and remove outer wrapping from case.
The slat retainer screws must be removed before installation. Use supplied 1/8" nex key to remove silver shipping brackets attached
to slat and screen case. Orient the case with the slat down and then remove the screws. The case must remain in that orientation
throughout the installation process to avoid fabric damage.
The Tensioned Large Cosmopolitan® Electrol® comes with brackets to allow for wall mount or ceiling mount installations.
Procedures for each method are as follows::
Wall Mount
1. The wall mount bracket should be fastened to wall studs or
some reinforcement within the wall. Concrete or brick walls
require special fasteners and anchors.
2. The wall bracket has holes spaced at 16" and 24" to align with
most wall studs.
Case Hook
2
"
3. The bracket must be level and plumb.
4. Keep in mind you will need at least 23/4" between the ceiling
and the top of the wall mount bracket to be able to position
the case on the bracket.
5. Mount the screen case on the wall bracket as shown in
igure 1. Be sure the case is fully seated on the bracket.
Tighten the stop screws against the wall bracket.
Ceiling Mount
1. Be sure the ceiling has adequate reinforcement to attach the
screen brackets.
2. Attach the ceiling brackets to the wall mount bracket using
the supplied 5/16" x 3/4" bolts, washers and nuts.
3. Position the ceiling bracket assembly on the ceiling and
attach with 5/16" bolts (not supplied). The bolts should be
long enough to pass through the drywall or ceiling tile and
penetrate at least 11/2" into the reinforcement in the ceiling.
4. Mount the screen on the wall bracket as shown in igure 2. Be
sure the case is fully seated on the bracket. Tighten the stop
screws against the wall bracket.
Wall Mount
Bracket
Stop Screw
Viewing Surface
(Audience Side)
Figure 1
1 ⅛"
Case Hook
Ceiling Mount
Bracket
⁄ x ¾" Bolt
Nut and Lock
Washer
Wall Mount
Bracket
Stop Screw
Viewing Surface
(Audience Side)
Figure 2
Screen Adjustment
Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. No further
adjustment is necessary.
CAUTION: Contact Da-Lite at 8006223737 or 5742678101 if screen motor needs adjustment.
ATTENTION:Contactez Da-Lite au 8006223737 ou au 5742678101 au cas le moteur de l'écran a besoin d'être ajusté.
3
Page 4
Tensioned Large Cosmopolitan® Electrol® Installation For Screens
Without A Built-In Low Voltage Control
Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box located on the left end of
the screen case.
See wiring diagram below for wire connections.
NOTE: This screen can only be controlled by a single 120VAC or 240VAC wall switch. To use multiple switches, an optional low voltage control
must be used.
120V Wiring Diagram
For Standard Wall Switch
Junction Box
Located In Left Endcap
NOTE: A single switch cannot be used
to operate more than one screen.
Contact the factory for further
information.
SPDT Switch with
Center Of
Up
Of
Down
Black
Red
White
Red (Up)
Black (Down)
AC (Common)
AC Hot 120VAC 60HZ 1 AMP
Black/Yellow
White
Red
Black
Green
Motor
This Switch Can Not
be used with LVC.
240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH:
Da-Lite ofers two styles of 240 volt wall switches for standard operation.
Please see wiring diagram in wall switch boxes included with screen.
4
Page 5
UP
STOP
DOWN
UP
STOP
DOWN
Installation For 120V Screens
120V Wiring Diagram
3-conductor 2024 gauge wire can be used in place of the
supplied RJ14 cable to connect the wall switch. Connect the
BUS terminals on the wall switch to the corresponding BUS
terminals on the splitter board.
Up Limit
Led
Tactile Button
BUS
COM
5V
Down Limit
Bus
Tactile Button
Front of
Wall Switch
Back of
Wall Switch
RJ22
Jack
RJ22 Jack
(Connection to
Wall Switch)
RJ22
Inputs
IMPORTANT NOTE: The wall switch is REQUIRED to make any
limit switch adjustments, EVEN if a third party control system is
used. Therefore, it is advised to wire the switch or provide a
3-conductor connection that is accessible.
RJ22
Output
Up (Dry Contact)
Down (Dry Contact)
Common (Both)
Bus (Bus)
5V (Bus)
RJ45
Receptacle
RJ45 Jack
Data
Cable
RJ14 Pin-Outs (Tab Is Facing Up)
Bus (RP Data)
RQ Data
+5V
Ground
Supplied RJ14 cable
White
Green
Red
Black
Power
Wire
White
(Common)
Black
(Hot)
Power Input 120VAC / 60Hz
Green (Ground)
(Ground–Must be Connected
to Building Ground)
RJ22 Pin-Outs (Tab Is Facing Up)
+12V
Bus (RP Data)
RQ Data
+5V
Ground
RQ Clock
Standard RJ22 can be used in place of RJ14 cable
Blue
Yellow
Green
Red
Black
White
RJ45 Pin-Outs (Tab Is Facing Up)
Manual 2
+12V
Bus (RP Data)
RQ Data
+5V
Ground
RQ Clock
Manual 1
Brown
Blue
Yellow
Green
Red
Black
Orange
Purple
5
Page 6
Installation for 220/240V Screens
240V Wiring Diagram
IMPORTANT NOTE: The wall switch is REQUIRED to make
any limit switch adjustments, EVEN if a third party control
system is used. Therefore, it is advised to wire the switch
or provide a 4-conductor connection that is accessible.
Blue (Common)
Power Input
240VAC / 50Hz
Brown (Hot)
Green
Motor
Green
Ground to Case
NOTE: Ground–Must be
Connected to Building
Ground
UP
COM
DN
+5V
Splitter
Dry Contacts
ILT RJ9 Pin-Outs (Tab Is Facing Up)
IR or Up
Ground Common
+5V
Data or Down
RJ9RJ9
Black
Red
Green
White
UP
STOP
DOWN
Front of Wall
Switch
UP DN
3POSITION
SWITCH RJ9
GND
+5V
Back of
Wall Switch
6
Page 7
Troubleshooting
Visit www.da-lite.com to ind installation and troubleshooting
videos and tutorials. You will also ind a link to Live Chat for
interactive support and you can contact us by email at info@dalite.com or by phone at (800) 6223737 or (574) 2678101 with any
troubleshooting questions.
Symptom Cause Solution
Blown fuse. Replace fuse.
Tripped circuit breaker. Reset circuit breaker.
Check above. Tighten all loose wire connections.
Correct any improper connections.
No power to operating switch
or junction.
Screen will not operate.
Motor does not hum.
Down Position
Check for power across black and white leads.
Up Position
Check for power across red and white leads.
Power at junction box
Thermal overload tripped.
Broken wire in the “down” or “up” position. Check for continuity. Cut o old splice and reconnect.
Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.
Capacitor burned out. Replace motor assembly.
Incorrect stopping position in
downward direction.
Incorrect stopping position in
upward direction.
Noise.
NOTE: Screen will operate
with a low pitched hum.
Coasting. Defective brake. Replace motor assembly.
Lost roller wrap. See instructions below.
“Down” limit switch out of adjustment. Contact Da-Lite at 8006223737 or 5742678101.
Lost roller wrap. See instructions below.
“Up” limit switch out of adjustment. Contact Da-Lite at 8006223737 or 5742678101..
Gear noise. Replace motor assembly.
Let motor cool down for 15 minutes. Try again.
7
Page 8
LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574. 267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0179 (Rev. 2) 10.14
© 2014 Milestone AV Technologies LLC. Printed in U.S.A.
98770
Loading...