
Pre-Installation Installation
Having decided on hooks, chains, cables or other mounting 
method, have mounting prepared before opening box.  
Do not mount screen against walls that might rub fabric.
1. Remove screen from box by lifting roller at the ends. Be 
careful not to permit lid or any tools to fall on screen. During 
installation handle unit only by ends of roller and top header. 
Do not grasp around fabric –do not rest unit on fabric.
2. Remove wrapping paper and unwind ropes.
3. With the screen lying on the loor, install the clamps on the 
reinforcement tape on the header as shown in Figure 2. 
Clamp assembly is shown in Figure 1. Drop the closed loop of 
the turnbuckle in the slot of the clamp before inserting bolt. 
Each clamp uses three bolts and nuts. Do not tighten nuts 
any more than inger tight. Make sure the ends of clamps do 
not push into the fabric. Pulleys at each end of header must 
be in the vertical position, when hung for proper operation.
4. Adjust top header in fabric pocket to the 21/4" and 33/4" 
position shown on the drawing.
5. Hang the screen in place at three, ive, or seven points.
   CAUTION! When this screen is shipped from the factory, 
there are 2-1/2 turns of rope around each end of the roller. 
Make certain that this is left unchanged to insure good 
operation.
   CAUTION! Before dropping fabric make certain ropes 
at end of bottom roller do not overlap. Overlapping of 
ropes will cause rope to work inward and thus damage 
the fabric.
Figure 1 – Clamp Assembly
2

Screen Adjustment
1. Lower screen slowly by gradually releasing ropes.
2. With screen in the “Down” position, turn the header in the 
fabric pocket carefully to adjust the pulleys to a vertical end 
position. Check the 21/4" and 33/4" end tube dimensions. 
Adjust the clamps on the reinforcement tape. Clamps are not 
to push into fabric pocket. Tighten nuts on all bolts.
3. Total screen drop may be controlled by adjusting rope clamp. 
Do not adjust for more drop.
4. With unit in completely unrolled position, examine the screen 
carefully. If slight sag appears in center of fabric, adjust 
turnbuckles at the eye bolts until fabric hangs lat.
5. Screen may be raised by pulling on ropes. Tie of ropes to 
keep screen in raised position.
Mount at These Points Only
2 ¼"
6" 6"
Turnbuckle – Adjust  
for Flat Fabric Hang
6. Protect your screen against damage and it will give many 
years of enjoyment.
a.  When lowering screen, do so gently. Never allow it to 
drop uncontrolled.
b.  Before raising screen, be sure both front and back sides 
are free from insects or any foreign matter.
c.  Form the habit of looking in space between fabric and 
roller for foreign matter before raising screen.
d.  Caution stage hands and others to avoid bumping 
screen with ladders, scenery, etc.
3 ¾"
Locate Clamps on 
Reinforcement Tape
Mount Header 
Tube Level
Pulley Must be Installed 
in The Vertical Position
Handle Unit Only 
by Top Header and 
Roller Ends During 
Installation
Center Line of Screen
Check Here for Foreign 
Matter Before Raising 
Screen
Do Not Handle Unit by 
Fabric Area
Don't Adjust 
Rope Clamp 
Already Set 
for Proper  
Full Screen 
Opening
Figure 2
3

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in 
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly 
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the 
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered 
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. 
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, 
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.  
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use, 
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives 
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED 
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION 
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137, 
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS 
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
A Milestone AV Technologies Brand
3100 North Detroit Street 
Warsaw, Indiana 46582 
P: 574.267.8101 or 800.622.3737 
F: 574.267.7804 or 877.325.4832 
E: info@da-lite.com 
www.da-lite.com
DL–0132 (Rev. 2) 12.13 
© 2013 Milestone AV Technologies LLC. Printed in U.S.A.
45037