Da-Lite Professional Electrol User Manual
INSTRUCTION BOOK FOR
Professional Electrol
®
Important Safety Instructions
When using your video equipment, basic safety precautions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
Save These Instructions
Pre-Installation
1. Carefully unpack screen.
2. Make sure to recheck measurements of screen location
before installation.
3. Remove instruction cover plate (Fig. 1). Do not remove
wrapping paper or tape strips until screen is installed.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Ironing Board
Professional Electrols 14' and over contain an ironing board to
latten the fabric (long strip attached). The ironing board is part
of the screen case. Do not remove. Contact Da-Lite if the ironing
board is in need of adjustment. (Fig. 2).
Tape Strip
Instruction Cover
Figure 1
Case
Ironing Board
Figure 2
2
Installation
Screens Up to 18' Wide
9 ½"
Length = Fabric Width
+10", All Sizes
Reinforced
Top
Motor
End
Electrical
Outlet Box
5"
Suggested Methods of Installation
NOTE: For Exposed Installation If the screen is to be mounted
in an exposed position, it may be covered with inished plywood,
veneer, paneling, plastic wall covering or a valance.
Motor In The Roller
Screen Without Doors
5"
11 ⁄"
Screens 20' and Wider
Length = Fabric Width
+10", All Sizes
Reinforced
Top
Motor
End
Electrical
Outlet Box
5"
10 ¾"
12 ⁄"
5"
Motor In The Roller
Screen Without Doors
Ceiling Type Hanger
Picture
Surface
Wall or Ceiling Mount With Hangers
Wall type hangers and ceiling type hangers are
standard equipment. One set is supplied with
each screen. Useful for recessed installations.
Wall Type Hanger
Picture
Surface
2" Moulding
Picture Surface
1" x 3" Cleat
Ceiling Mount
Without Hangers
Screen case is placed lush with
the wall and ceiling and held in
position by moulding securely
attached to the wall.
Rafters
Picture
Surface
Recessed Above Ceiling
Other methods of installation
will suggest themselves in new
buildings where it would be an
easy matter to provide a recess
for the screen to conceal it when
not in use.
Do not seal in—allow access.
3
Installation
Hangers (If required)
1. See Figure 3 for hanger placement.
2. On screens equipped with an ironing board, make sure
hangers do not interfere with the ironing board brackets.
11 1⁄2"
Screens 22' Wide And Under
Case Length ÷ 2
11 1⁄2"
11 1⁄2"
Case Length ÷ 2
(Case Length – 23") ÷ 3
(Case Length – 23") ÷ 3
(Case Length – 23") ÷ 3
Screens Over 22' Wide
1
11
⁄2"
3. Level unit lengthwise with a carpenter’s plum level.
CAUTION! Do Not completely seal in unit. Access room
must be allowed for motor repair or fabric replacement
ATTENTION! Ne ixez pas complètement l'unité. Un
espace doit être laissé pour pouvoir réparer le moteur
ou remplacer la toile..
4. Remove shipping brace by removing 2 hex head screws
(Fig. 4).
5. Remove wrapping paper and tape strips (Fig. 4).
CAUTION! Do not cut wrapping paper or tape with
knife or any sharp tool. Remove by hand.
4
Figure 3
ATTENTION! Ne coupez pas le papier d'emballage ou le
ruban adhésif avec un couteau ou un outil tranchant.
Retirez à la main.
6. Install electrical hook up that applies to your unit. Make sure
to review your Electrical Installation Checklists and wiring
diagrams (included) for either 110 volt switch, 220/240 volt
switch, or DRC low voltage control.
7. Test installation by carefully running surface up and down
several times. Be prepared to stop screen.
NOTE: The picture surface, when rolled down, should have
at least a full wrap and a half around the roller. Do not allow
any part of the roller to become exposed.
Loading...