Da-Lite IDEA Panoramic Instruction Manual

INSTRUCTION BOOK FOR

IDEA™ Panoramic

Preparation

Note: It requires at least four people to assemble an IDEA
Panoramic. To maintain optimal projected image geometry and
screen alignment, a lat and straight wall free from obstructions
and angular distortions should be used.

Tools Required For Assembly

Phillips Screwdriver

Rubber Mallet

Hardware Provided

Choose a clean work area for assembly using padded material or
other soft, clean materials. The work area should be larger than
the overall screen size and directly in front of the location where
the screen is to be installed.

Level

Measuring Tape ⅜” Open Wrench

or Socket Driver

#8 x ½” Screws

Number of supplied screws

varies by screen size

44” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.

28” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.

18” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.

(6) LBrackets (8) 1032 Nuts

(2) Seam Brace

2

Hardware Provided

Item Number Overall Dimensions

27966 36¾" x 144¾" 36" x 64" (2) 28" (2) 28"

27981 36¾" x 144¾" 36" x 57½" (2) 28" (2) 28"

27963 46¾" x 144¾" 46" x 81¾" (2) 28" (2) 28"

27978 46¾" x 144¾" 46" x 73½" (2) 28" (2) 28"

27960 50¾" x 144¾" 50" x 89" (2) 44" (2) 18"

27975 50¾" x 144¾" 50" x 80" (2) 28" (2) 28"

27957 53¾" x 144¾" 53" x 94¼" (2) 44" (2) 18"

27972 53¾" x 144¾" 53" x 84¾" (2) 28" (2) 28"

27954 60¼" x 144¾" 59½" x 106" (2) 44" (2) 18"

27969 60¼" x 144¾" 59½" x 95¼" (2) 44" (2) 18"

27965 36¾" x 168¾" 36" x 64" (2) 28" (2) 44"

27980 36¾" x 168¾" 36" x 57½" (2) 28" (2) 44"

27962 46¾" x 168¾" 46" x 81¾" (2) 28" (2) 28"

27977 46¾" x 168¾" 46" x 73½" (2) 28" (2) 44"

27959 50¾" x 168¾" 50" x 89" (2) 44" (2) 28"

27 974 50¾" x 168¾" 50" x 80" (2) 28" (2) 44"

27956 53¾" x 168¾" 53" x 94¼" (2) 44" (2) 28"

2797 1 53¾" x 168¾" 53" x 84¾" (2) 28" (2) 28"

27953 60¼" x 168¾" 59½" x 106" (2) 44" (2) 28"

27968 60¼" x 168¾" 59½" x 95¼" (2) 44" (2) 28"

27964 36¾" x 192¾" 36" x 64" (2) 28" (2) 44"

27979 36¾" x 192¾" 36" x 57½" (2) 28" (2) 44"

27961 46¾" x 192¾" 46" x 81¾" (2) 28" (2) 44"

27976 46¾" x 192¾" 46" x 73½" (2) 28" (2) 44"

27958 50¾" x 192¾" 50" x 89" (2) 44" (2) 44"

27973 50¾" x 192¾" 50" x 80" (2) 28" (2) 44"

27955 53¾" x 192¾" 53" x 94¼" (2) 44" (2) 44"

27970 53¾" x 192¾" 53" x 84¾" (2) 28" (2) 44"

27952 60¼" x 192¾" 59½" x 106" (2) 44" (2) 28"

27967 60¼" x 192¾" 59½" x 95¼" (2) 44" (2) 44"

Wall Brackets Included

Center Panel Viewing Area

(H x W)

Center Panel Wall Brackets Side Panel Wall Brackets

Table 1

3

Assembly Instructions for Panoramics with 24” Marker Tray

1. Carefully unpack unit and place all panels on top of the clean
work area. The viewing surface of each panel must face down.

NOTE: For optimal seam alignment, use labels on the back side of

each panel to arrange for assembly.

2. Slide all three panels together, aligning the both the top and
bottom frames (Figure 1).

3. Find (1) seam brace and remove the release liner from both strips
of adhesive tape.

4. Ensuring that the panels are still in alignment, line up the seam
brace with one of the panel seams with adhesive side facing
down. Do not press adhesive into panels yet. Maintain at least a
small gap between the adhesive and the panel.

5. Use ⅜” open wrench or socket driver and (4) 1032 nuts to attach
seam brace onto the studs on the top and bottom of screen
frame at the panel seam. Tighten all four nuts once attached to
the frame (Figure 2).

NOTE: For optimal seam alignment, hold the panels together

tightly while the seam brace is being adhered and the lock nuts
are being tightened.

6. Press adhesive into panels. Apply steady pressure along the
length of the seam brace to attach irmly.

7. Repeat Steps 36 to attach the other seam brace.

1032 Nuts

Figure 1

Seam Braces

Figure 2

4