Da-Lite IDEA Instructions Manual

Printed in U.S.A. 71858 Rev. 7/12

Instructions for

INTERACTIVE DRY ERASE

APPLICATION IDEA SCREEN

The Da-Lite Difference.

DA-LITE SCREEN COMPANY LLC

3100 North Detroit Street
Post Office Box 137
Warsaw, IN 46581-0137 USA
P 800-622-3737 / 574-267-8101
F 877-325-4832 / 574-267-7804
www.da-lite.com
e-mail: [e-mail]

LIMITED ONE YEAR WARRANTY

ON DA-LITE PRESENTATION PRODUCTS

Da-Lite Screen Company LLC warrants its products to the original purchaser
only, to be free from defects in materials and workmanship for a period of one
(1) year from the date of purchase by the original purchaser provided they are
properly operated according to Da-Lite’s instructions and are not damaged due
to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse,
abuse or accidental damage, or which has been tampered with or repaired by
a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at
Da-Lite’s option) the defective part of the merchandise. Returns for service
should be made to your Da-Lite dealer. If it is necessary for the dealer to
return the screen or part to Da-Lite, transportation expenses to and from
Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage
in shipment. To protect yourself against damage or loss in transit, insure the
product and prepay all transportation expenses.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE
AND MERCHANT ABILITY. Any implied warranties of fitness for use, or

merchantability, that may be mandated by statute or rule of law are limited
to the one (1) year warranty period. This warranty gives you specific legal
rights, and you may also have other rights, which vary from state-to-state.

NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING
FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR
INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite
product, you may contact our Sales Partners at PO Box 137, Warsaw, IN
46581-0137, [phone], [phone].

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE
SHALL NOT BE BOUND BY THIS WARRANTY IF THE
PRODUCT IS NOT OPERATED IN ACCORDANCE WITH
DA-LITE’S WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original
ownership.

ASSEMBLY INSTRUCTIONS WALL MOUNTING

Note: It requires two people to assemble an IDEA Screen.

PREPARATION

Have space for this available on a flat clean surface such as a large table. The
work area should be larger than the frame size.

TOOLS REQUIRED FOR ASSEMBLY

Phillips screwdriver

ASSEMBLY

1. Carefully unpack unit and place frame assembly on top of a clean table. The
white surface must face up.

2. Center aluminum tray to the bottom of frame and attach with the provided (5)
#8 x

1

⁄2" screws (see figure 1). Insert screws through the tray into the groove.

WHITE SURFACE

ALUMINUM
TRAY

#8 x

1

⁄2" SCREWS

SECURE TRAY TO FRAME

FIGURE 1

1. The screen is shipped with one 44" wall bracket. This bracket must be
mounted to a flat surface into at least two wall studs.

2. Secure bracket to wall studs at the desire height. Make sure the bracket is
level. Drill holes and attach mounting bracket into wall. You will need at least
1" clearance above the drilled holes to hang the screen

3. This step requires two people. Hang the screen on the wall bracket (see
figure 2). There is a lip on the back of the frame that wedges itself into the
wall bracket once fully installed.

4. Attach bottom of screen to wall with two screws. The bottom mounting
holes are located under the tray (see figure 2).

FIGURE 2

WALL BRACKET

SCREWS
(NOT SUPPLIED)

SCREWS

ATTACH BRACKET TO WALL
SECURE BOTTOM OF SCREEN TO WALL