Page 1
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
POWER
PRESENTATION PRODUCTS
The
In
Instruction Book for
DESIGNER CONTOUR®MANUAL
Page 2
There are three ways to install the Designer Contour
®
Manual: Wall Mount, Ceiling Mount, or Ceiling Hook.
Procedures for each method are as follows:
Wall Mount
1. Secure the wall mount bracket to the wall at the
desired height. Bracket should be fastened to wall
studs or some reinforcement within the wall.
Concrete or brick walls require special fasteners
and anchors.
2. Make sure the bracket is level. See figure 1 for
reference dimensions.
3. Keep in mind you will need at least 7/8" between
the ceiling and the top of the wall mount bracket
to be able to position the case on the bracket.
4. Mount the screen case on the wall bracket as
shown in figure 1. Be sure the case is fully seated
on the bracket. Tighten the stop screws against
the wall bracket.
Ceiling Mount
1. Do not remove the wall mount bracket, even if
you are not using it for mounting. This provides
structural stability to the case.
2. Be sure the ceiling has adequate reinforcement to
attach the screen brackets.
3. The top of the screen case has a channel that the
ceiling mount brackets slide into. Loosen the two
set screws on the brackets and slide bracket so it
extends over the end of the case. Lock the
brackets in place by tightening two set screws.
Refer to figure 2. Mount cannot be more than 12"
from end of case.
4. Hold the screen case up to the ceiling and mark
the hole locations. Drill holes into the ceiling and
attach screen with the appropriate fasteners for
your ceiling.
SET SCREWS (2)
CEILING
MOUNT
HOLES
FIGURE 2
FIGURE 1
4-1/4"
5/16"
9/16"
CASE
HOOK
WALL
MOUNT
BRACKET
4-5/8"
STOP SCREW
1
YOU HAVE MADE A WISE SELECTION…
in choosing a Da-Lite projection screen designed and engineered to produce the sharpest, most pleasing
pictures with maximum convenience.
PROTECT YOUR SCREEN by keeping it rolled in its protective case when not in use. Always examine both front and back of
surface before re-rolling into case to make certain screen is free of dust, dirt or other foreign matter. Use a very soft
duster brush gently to remove foreign particles.
Care in mounting and care in correct operation will mean a long and satisfactory life for your Da-Lite wall/ceiling screen.
Locate the screen where the audience can best see it and where other furnishings in the room permit. Mount the screen
so that bottom of picture surface, when fully extended, will be above heads of viewers.
INSTALLATION
Page 3
2
HOOK MOUNT
HOLE
SET SCREWS (2)
FIGURE 3
TO LOWER PICTURE SURFACE
Pull screen down all the way. HESITATE – then allow screen to retract VERY SLOWLY until it locks in place.
TO RAISE PICTURE SURFACE
Pull straight down on the pull bail, then release quickly. The screen will retract gently into the case.
INSTALLATION
Ceiling Hook
1. Do not remove the wall mount bracket, even if
you are not using it for mounting. This provides
structural stability to the case.
2. Be sure the ceiling has adequate reinforcement to
attach a hook anchor.
3. The top of the screen case has a channel that the
ceiling hook brackets slide into. The brackets can
be attached anywhere within 12" of the end of the
case. Loosen the set screws on the brackets and
slide the brackets to the desired location. Lock the
brackets in place by tightening two set screws.
Refer to figure 3.
4. Attach an S-hook or similar fastener to the large
center hole on the bracket.
OPERATING INSTRUCTIONS
Page 4
Printed in U.S.A. 93015 Rev. 12/08
QUALITY FEATURES FOR BETTER PICTURES,
EASIER OPERATION, LONGER LIFE
• Exclusive Camlok®Roller System
• Attractively styled
• Easily installed
• Economically priced
• Completely self-storing
• Ideal for houses of worship, schools, family centers
and industrial training rooms.
For the finest in film and video projection
DA-LITE IS MORE
THAN PROJECTION SCREENS
Da-Lite Tripod, Wall and
Ceiling and Electric Screens
Da-Lite Lecterns
Da-Lite
Project-O-Stands
and Easels
Da-Lite
Monitor Mounts
T-BAR CLIP
For Dropped Ceilings
50 lb. max. load capacity.
No. 23 ADJUSTABLE
WALL BRACKETS
Screen can be extended 10",
14", 153/4", 181/
4
", 20" or 24"
from wall by wing nut and bolt
adjustment.
No. 11 WALL BRACKETS
Screen can be extended 10"
or 14" from wall by changing
position of bracket.
No. 6 WALL BRACKETS
Screen can be extended 6"
from wall.
TILT LOCK
For Keystone Elimination
Holds back bottom of
screen in tilted position
to eliminate keystoning.
SCREEN ACCESSORIES
WALL BRACKETS - (75# per pair maximum)
Da-Lite No. 6 and No. 11 Non-adjustable wall brackets
and No. 23 adjustable extension wall brackets are ideal
for keystone elimination, clearance, or corner mounting.
The screen brackets should be fastened to the studding
or other solid surface and not in the plaster only.
S-HOOK
T-BAR CLIP
CEILING
Loading...