Page 1
INSTRUCTION BOOK FOR
Deluxe Model B
®
Page 2
Installation Setting Up Your Screen
The Deluxe Model B must be suspended from the ceiling or used
with extension type wall brackets to allow room for the
Automatic Tensionizer.
For Wall Mounting
Special extension wall brackets such
as Da-Lite’s No. 6, No. 11 or No. 23
brackets must be used if screen is
to be wall mounted. Check with your
dealer to determine which best its
your needs.
Brackets should be fastened
securely to a solid surface such as a
wooden reinforcement board and
not in the plaster only. Rarely will
wall studs be found to support both
ends of a screen. Various types of
fasteners are available from local
hardware stores.
For Ceiling Suspension
If the screen is to be ceiling
mounted, two screw hooks should
be placed in a beam or other solid
surface. For drop ceilings, Da-Lite’s
TBar Clips may be purchased.
These illustrations (all rear views for simpliication) show how
easy the Deluxe Model B Screen is to operate.
1. Remove plastic protective wrap from handle and tension arm.
2. To start unrolling the picture surface,
pull down on cord pull knob. Then
with hand resting on the handle, pull
screen down.
3. The automatic tension arm moves into
position in a precision-like manner.
4. When surface is down, a simple press
of contour-shaped handle locks it into
position… ready for the show!
5. To re-roll picture surface–press irmly
downward and counter-clockwise on lat
handle to release lock. Permit surface to
re-roll rapidly into case. Control upward
movement by lightly holding handle or
cord pull knob.
PROTECT YOUR SCREEN by keeping it rolled in its case when
not in use. Always examine both front and back of surface before
re-rolling into case to make certain screen is free of dust, dirt or
other foreign matter. Use a very soft duster to gently remove
any foreign particles.
2
Page 3
Screen Adjustment Screen Accessories
Wall Brackets
Da-Lite No. 6 and No. 11 Non-adjustable wall brackets and
Back View Of Screen
Case
Upper
Tension
Arm
Assembly
Upper Tension Arm Assembly
Channel
No. 23 adjustable extension wall brackets are ideal for keystone
elimination, chalkboard clearance, or corner mounting.
The screen brackets should be fastened to the
studding or other solid surface and not
in the plaster only. Suspend screen
from “D” rings.
No. 23 Adjustable
Wall Brackets
Screen can be extended
10"-24" from wall by wing
nut and bolt adjustment.
No. 11 Wall Brackets
Screen can be extended
10" or 14" from wall by
changing position of
bracket.
Nut
NOTE: Tensioning of the Deluxe Model B picture
surface was made at the factory. Should more
tension be required, the screw in the channel
holding the upper tension arm assembly should be
moved upward in holes allotted for this purpose. For
any adjustment, it is recommended that the screen
be removed, placed on a lat surface and a pair of
pliers and a Phillips screwdriver be used in removing
the screw and nut.
Protect Your Screen
Before re-rolling surface into case, examine both
front and back of surface to be sure they are free
of foreign matter.
Screw
T-Bar Clip
For Drop Ceilings
50 lb. max. load
capacity.
No. 6 Wall Brackets
Screen can be extended
6" from wall.
Tilt Lock
For Keystone Elimination
Holds back bottom of
screen in tilted position
to eliminate keystoning.
3
Page 4
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0259 01.14
© 2013 Milestone AV Technologies LLC. Printed in U.S.A.
48709
Loading...