Manuel d’instructions de la
PLAQUE DE CUISSON INDUCTION
Cooking Hob
CECP701FSA
Cooking Zones 4 INDUCTION
Supply Voltage
220-240V 50/60 Hz
400 V 50/60 Hz
Installed Electric Power
(W)
Product Size
D×W×H(mm)
Building-in Dimensions
A×B (mm)
Induction Hotplate
pearance
Ap
7200
590×520×55
560×490
2
Dear customer:
Thank you for purchasing the the induction hotplate our product can
serve you many years to your satisfaction.
Please read this instructions manual carefully before using and
installation, keep it cautiously after reading for future reference.
Thank you for your purchase of the induction hotplate again, and wish
you to enjoy the pleasure by it.
Product Introduction
The induction hotplate can meet various demands of cuisine by
electromagnetic heating, with micro-computerized control and multifunction,
really the optimal choice for modern families.
The induction hotplate centers on customers and adopts personalized design,
and which will make your life comfortable and enabling to fully enjoy the
pleasure of life.
We have designed this hob for private use in home.
Working Principle
The induction hotplate is mainly composed of an induced heating coil, hotplate
made of ferromagnetic materials and control system.
In principle, current generates a powerful magnetic field via the coil. Large
numbers of vortexes are produced in the way that the magnetic lines in the
field contact the bottom containing iron or stainless steel substances. The
tremendous energy generated by the vortexes can heat the food directly by
converting efficiency heat energy penetrating through the bottom.
3
Figure (1)
Over- Temperature Protection
A temperature sensor equipped can monitor the temperature inside the
hotplate. When an excessive temperature is monitored, the induction hotplate
will stop operation automatically.
Pot Detection
When an unsuitable size or non-magnetic pot (e.g. Aluminum), or some other
small item (e.g. knife, fork, key) has been left on the hob, or the pot has been
removed, the hob can stop heating immediately. If there is no suitable pan put
on the right hob in one minute, the hob will go automatically into the standby
state, and the buzzer will sound for warning at one time.
Heat Indication
When the hotplate is used for a long time, waste heat remains in the heating
zone in a few minutes. The code “H” appears, warning to be away from the
heating zone.
Protection of Shutting Down Automatic
Shutting down Automatic is a safety protection function for your induction
hotplate. It will shut down automatically if you forget to turn off your cooker.
The default working times for various power levels are shown in the
following table:
Power level
The heating zone shut down automatically
after
1~5 8 hours
6~10 4 hours
11~14 2 hours
15
1 hours
*Remind:
The patient with a heart pacemaker shall use this product under the guidance
of the doctor.
4
Selection of installation equipment
Drill holes on the table surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 50 mm space shall be
preserved around the hole.
Be sure the thickness of the table surface is at least 30mm. Please select
heat-resistant table material to avoid larger deformation caused by the heat
radiation from the hotplate.
As shown in Figure (2)
49
c
m
ni
i
m m
5c
ni
i
m m
5c
Figure (2)
5
cm mini
m
c
56
Under any circumstances, make sure the induction hotplate is well ventilated
and the air inlet and outlet are not blocked.
Ensure the induction hotplate is in good work state.
As shown in Figure (3)
mini 760mm
Air exit
mini 5 cm
mini 2 cm
Air intake
mini 5 mm
Figure (3)
5
Note: The safety distance between the hotplate and the cupboard above the
hotplate should be at least 760mm.
Fix the hob on the table by screw four brackets on the bottom of hob (as
shown in figure (4)) after installation. Adjust the bracket position to suit for
different table top thickness.
Figure (4)
Cautions:
1. The induction hotplate must be installed by qualified personnel or
technicians. We have professionals at your service. Please never conduct
the operation by yourself.
2. The induction hotplate shall not be mounted to cooling equipment,
dishwashers and rotary dryers.
3. The induction hotplate shall be installed such that better heat radiation can
be ensured to enhance its reliability.
4. The wall and induced heating zone above the table surface shall withstand
heat.
5. To avoid any damage, the sandwich layer and adhesive must be resistant to
heat.
ELECTRICAL CONNECTION
"The installation must conform to the standard directives."
The manufacturer declines all responsibility for any damage that may be
caused by unsuitable or unreasonable use.
6
Power line connection
The socket shall be connected according to the relevant standard or
connected to a single-pole breaker.
The method of connection is shown in Figure (5):
blue
grey
green-yellow
N2 N1 L2 L1
220-240V
PE
connet to the main power supply
220-240V 2+2N~
brown
220-240V
black
blue
grey
black
green-yellow
PE
connet to the main power supplyconnet to the main power supply
brown
NL2 L1
220-240V
220-240V
400V~ 2-N
Figure (5)
400V
blue
green-yellow
PE
220-240V~
grey
NL
220-240V
brown
black
If the cable is damaged or needed to be replaced, the operation must be
carried
out by the after-sale agent with dedicated tools to avoid any accidents.
If the appliance is being connected directly to the mains an Omni-polar
rcuit-breaker must be installed with a minimum opening of 3mm between
ci
ntacts.
co
The installer must ensure that the correct electrical connection has been made
and that it is compliant with safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorized technicians
only.
7
Induction Hotplate Appearance
23
Ceramic plate
14
Control panel
Figure (6)
Air entry
Air vent
8
Schematic Diagram of The Control Panel
Timer key
structions For Use
In
Prepar
After p
ation Before Using:
ower on, the buzzer beep once, all the indicators light up for 1 second
Heating zone selection key
S
lide key
Regulating key
Figure (7)
Boost
Function key
On/OFF
Lock
and then go out, which indicates the induction hotplate enters the state of
andby.
st
Put the pot in the center of the heating zone.
Operation Instructions:
When the “ON / OFF” button is pressed, all the indicators show "-" or "---"
OR
ording to the heating zone where the pot is placed, select a relevant zone
Acc
selection (e.g. select zone 1), with a corresponding power level indicator
flashing.
At the moment, press the "+" button, the indicator displays "8", or press the "-"
button, the indicator displays "1",then adjust the power u levels sing the "+", "-"
button or the slider
9
POWER UP
POWER DOWN
Or press the "+" and "-" buttons simultaneously, the power setting
immediately chang to 0, and the relevant cooking zone switches off.
AND
See the attached table "the max power of each heating zone" for the power
specific to each heating zone.
Note: 1. After the "ON/OFF" button is pressed, the induction hotplate will restore
to its standby state if no any operation is carried out within one minute.
Boost function
To get a quicker heating speed, there is a function named “Boost” will satisfy
your requirement.
Directly press the “ Boost” button after selecting the heating zone, with the
power level indicator showing “P. ” , and the heating power can reach up to the
max. (e.g. select zone 1)
Note:1. The boost function only operates for 5 minutes, after which the cooking
zone returns to its orginal setting.
2. The boost function works on the all cooking zones.
3. As the boost function is activated ,the other cooking zone of the same side
is limited under level 2 automatically(for example, when the 2nd cooking
zone's boost function is activated, the 1st cooking zone which is of the same
left side will be limited under level 2 automatically).
Cancellation of “Boost” function
When in the "Boost" function, select the relevant heating zone with the “Boost”
function, and press the "Boost" button or the "-" button to cancel the Boost
function, then the cooking zone will revert to its original setting.
10
OR
Or press the "+" and "-" buttons simultaneously when the relevant heating
zone has been selected, the “Boost” function will be cancelled automatically.
The power setting immediately chang to 0, and this heating zone switch off at
the same time.
AND
Timing function
Select the relevant cooking zone, and set the power level with the “+” or “-”
button. (e.g. the cooking zone 1 with power level 6)
Press the "Timing" button, the timing indicator flashes, and you can set the
timer at this point.
AND
Using the “+” and “-“buttons, you can realize the setting of timing from
0 to 9:59 minutes.
OR
Press the "+" key once increases the time by one minute ;
increases the time by 10 minutes .
the "+" key
Press the "-" key once decreases the time by one minute ;
decreases the time by 10 minutes .
the "-" key
increases the time by 30 minutes .
decreases the time by 30 minutes .
When the time exceeds 1 hour, hold down the
When the time exceeds 2 hours, hold down the
~
hold down the "+" key
hold down the "-" key
Timing confirmation:
After selecting a set time, once the timing indicator flashes for 5 seconds, or
press the “Timing” button, the set time will be confirmed to be valid
automatically.
Timing cancellation:
If press the "+" and "-" simultaneously, the timing can be cancelled
automatically, with the timing indicator showing “0”.
11
AND
Note: 1. In the timing state, the power level of the relevant cooking zone can be
changed, and the time set is still valid.
2. Press the timing button without select one cooking zone when the induction
hotplate is working, the time-warning function will operate. And the warning time
can be set just like the timing function. The buzzer will be beeping for 30 seconds
when the time is reached. The function will be cancelled when the time is set to.
3. the time-warning function will be cancelled when the induction hotplate is
switched off.
4.Timer can be set on all 4 cooking zones. When you set the time for several
cooking zones simultaneously, decimal dots of the relevant cooking zones
are on.
5. on the timer display will be shown the timer than will expire first. The dot of
the corresponding zone will be on but flashing. Once the countdown timer
expires the corresponding zone will be switch off. Then it will be shown the
new first expiring timer and the corresponding zone will have the dot flashing.
Interlock Function:
To ensure the safety of children, the induction hotplate is provided with the
function of interlock.
Interlock:
Press the “Interlock” button, then the induction hotplate enters the locking state,
with the timing indicator showing “Loc”.
Unlock:
Holding the “Interlock” button for about 3 seconds, the locking state will be
removed.
Note:
1. The rest buttons disabled except the “ON/OFF” and “Interlock” button when
the induction hotplate is in the locking state. Only unlocking the buttons or else
the induction hotplate won’t be operated.
2. If the induction hotplate enters the locking state in the off mode, the timing
indicator showing “Loc” for one minute. And it will be shown for one minute
again when the “ON/OFF” or “Interlock” button is pressed.
12
Loading...
+ 26 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.