Da-Lite 92639L, 88376LS, 88368LS User Manual
INSTRUCTION BOOK FOR
Contour® Electrol
®
Important Safety Instructions
Pre-Installation
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating
at least equal to that of the appliance should be used. Cords
rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of ire, electric shock, or
injury to persons.
Tools Required for Installation
1. Carefully unpack screen and remove outer wrapping
from case.
2. Set aside the Installation Kit. Items inside will be used
during installation.
Installation
NOTE: Remove the black tape and rubber bands from the slat
bar after the case has been installed.
There are three ways to install the Contour Electrol — Wall Mount,
Ceiling Mount, or Ceiling Hook. Procedures for each method are
as follows:
Wall Mount
1. Using a #2 Phillips screwdriver, loosen the two stop screws
and remove the wall mount bracket from the back side
of the case (Figure 1).
NOTE: The ceiling lush mount and ceiling hook mount
brackets are attached to the top side of the case. These
brackets are not necessary for wall mounting and can be
removed at this time.
#2 Phillips Screwdriver
2. Secure the wall mount bracket to the wall at the desired
height. The wall mount bracket should be fastened to the
wall studs or some reinforcement within the wall. Concrete or
brick walls require special fasteners and anchors. Allow at
least 23/8” above the wall mount bracket to be able to
position the case on the bracket (Figure 2).
5 ⁄"
2 ⁄"
6 ⅜"
Case Hook
Wall Mount
Bracket
2 ⁄"
Stop Screws
Slat Bar
Figure 1
2
Installation (continued)
3. Make sure the bracket is level.
4. Hang the screen case on the wall mount bracket as shown in
(Figure 2). Be sure the case is fully seated on the bracket.
5. Tighten the two stop screws against the wall mount bracket
using a #2 Phillips screwdriver (Figure 1).
Ceiling Flush Mount
1. The ceiling hook brackets are attached to the top side of the
housing. They must be removed prior to ceiling lush mount.
Wall
NOTE: Do not remove the wall mount bracket, even if you are
not using it for mounting. This provides structural stability to
the case.
2. Using a #2 Phillips screwdriver, loosen the four 1/4”x 5/8” screws
holding the ceiling lush mount brackets (Figure 3).
3. Slide the ceiling lush mount brackets so that the mounting
holes extend beyond the ends of the case. All four 1/4”x 5/8”
screws must remain within the channels.
4. Tighten the four 1/4”x 5/8” screws holding the ceiling lush
mount brackets (Figure 3).
5. Before mounting your Contour Electrol, be sure the ceiling
has adequate reinforcement.
6. Hold the screen case up to the ceiling and mark the hole
locations. The brackets have a set of front holes and a set of
rear holes. Attach the Contour Electrol using the appropriate
hardware for your ceiling type. It is best to use at least one
hole in each set.
Ceiling Hook Mount
1. The ceiling hook mount brackets are tied together and
attached to the ceiling lush mount bracket at one end
of the case. Remove the ceiling hook mount brackets.
Wall Mount
Bracket
Figure 2
1/4 X 5/8"
Flat Head Screw
Figure 3
2. Remove the ceiling lush mount brackets using a #2 Phillips
screwdriver (Figure 3). Retain four 1/4”x 5/8” screws.
NOTE: Do not remove the wall mount bracket, even if you
are not using it for mounting. This provides structural stability
to the case.
3. The top of the screen case has two channels with threaded
nuts that slide the length of the case. Attach the two ceiling
hook mount brackets using the 1/4”x 5/8” screws and threaded
nuts, two per bracket. The brackets can be attached anywhere
within 12" of the ends of the case (Figure 4).
4. Before hanging your Contour Electrol, be sure the ceiling
has adequate reinforcement.
5. Using the holes in the ceiling hook brackets, hang the
Contour Electrol using the appropriate hardware and
fasteners for your ceiling type.
Ceiling Hook Bracket
1/4 X 5/8"
Flat Head
Screw
Figure 4
3
Electrical Installation
1. Open the junction box on the left end of the case using a #2
Phillips screwdriver. Install electrical connections that apply to
your unit. Make sure to review the wiring diagram for proper
hook up. Replace the junction box cover.
NOTE: Must be installed in accordance with the requirements
of the Local Building Codes, the Canadian Electrical Code
(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),
NFPA 70.
2. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor,
the standard duty cycle is 1 minute on and 3 minutes of.
Junction
Box Cover
Figure 5
4
Loading...