Da-Lite 24863 Instructions

INSTRUCTION BOOK FOR

Tensioned Advantage®

Deluxe Electrol

®

Important Safety Instructions

Pre-Installation

When using your video equipment, basic safety precautions
should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating
at least equal to that of the appliance should be used. Cords
rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of ire, electric shock, or
injury to persons.

Save These Instructions

1. Carefully unpack screen and remove outer wrapping
from case.

2. Make sure to recheck measurements of screen location
before installation.

Screw For

Securing Roller

Access Door

Fabric Door

Figure 1

Access
Door

Case Installation

1. The case provides multiple attachment points for bolts,
cables, or threaded rod. Page 7 shows threaded rod installed.
The variable position-mounting bracket may be located
anywhere along the length of the case. It is recommended to
keep the brackets spaced evenly enough to distribute the
weight of the screen.

The case has a self-trimming lange around the bottom.

Ceiling tiles or drywall may be placed on top of this lange to
provide a inished appearance.

2. After securing the case in the ceiling check that the case is
level and plumb.

3. Use supplied 1/8" hex key and a 1/4" wrench to remove silver
shipping brackets attached to slat and screen case.

4. Install electrical connections that apply to your unit. Refer to
the following diagrams for proper installation. The diagrams
on page 4 are for standard controls; the diagrams on page 5
are for SCB100 controls and page 6 for SCB200 controls. The
terminal block for the wall switch connections is located
under the metal housing surrounding the junction box.
Remove two screws for access.

2

Screen And Roller Assembly Installation

If your screen was shipped with the motor and roller already installed proceed to step 6.

1. Remove the screw from each end of the access door (front
door) and open the door. See igure 1.

2. Carefully unpack screen and roller assembly. Leave packing
paper on the roller.

3. Place the roller assembly into the case with the motor on the
left side. The limit switches should be facing down. Line up
the square pin on the motor with the square hole in the
bracket.

4. Lift the pin end (right end) of the roller into position and slide
the bracket onto the roller pin. Tighten two nuts to secure the
bracket.

5. Complete electrical hook-up by snapping motor wire
connector into case connector.

6. Remove shipping brackets by removing the hex head screws
from aluminum slat and case. Slat should move freely. See
igure 2. (Only if the roller assembly is preinstalled.)

Screen Motor

White

Adjustment

Knob "Down"

Black

Adjustment

Knob "Up"

7. Test installation by operating the screen several times. Be
prepared to stop the screen. Standard Duty Cycle: 1 MIN. ON/3
MIN. OFF. The fabric door (rear door) will not close until the
wall switch is placed in the up position and when the screen
motor stops at its limit switch in the up direction.

CAUTION: Excessive continuous operation may cause the

motor to overheat. If this happens the motor will shut of
until it cools to a normal operating temperature.

ATTENTION! Le fonctionnement continu et excessif peut

provoquer une surchaufe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la
température normale de fonctionnement.

8. Run the screen down enough to open the fabric door. Close
the access door and reinstall the screws to secure the door.

Access Door

Fabric

Door

Microswitch

Door Motor

Hex Head Screws

Figure 2 Figure 3

Shipping
Bracket

Door

SCB100/SCB200
Access Cover

Knockouts For
Conduit Installation

Screen Adjustment

CAUTION: Contact Da-Lite at 8006223737 or 5742678101 if screen or door motor needs adjustment.

ATTENTION: Contactez Da-Lite au 8006223737 ou au 5742678101 au cas le moteur de l'écran a besoin d'être ajusté.

3