Da-Lite 24787V Instructions

The Da-Lite Difference.

Instruction Book for

DASNAP SCREEN

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: [phone]
800-622-3737
Fax: [phone]
Toll Free Fax: [phone]
www.da-lite.com
e-mail: [e-mail]

Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________
Screens over 96" viewing width = 3

Quantity of 1. Only for screens
80" and smaller viewing width QUANTITY INCLUDED __________

SNAP STUD
QUANTITY INCLUDED ________

LARGE WALL BRACKET (47" LONG)

Installation screws not included

SMALL WALL BRACKET (8" LONG)

Installation screws not included

USE INSTALLATION
METHOD NUMBER __________

#10 SCREW
QUANTITY INCLUDED ________

FRAME BRACKET

Quantities vary by screen size
Screens 80" and smaller viewing width = 3
Screens over 80" to 96" viewing width = 4
Screens over 96" viewing width = 6

QUANTITY INCLUDED ________________________________

FRAME ASSEMBLY

1. Unpack the frame parts from the carton. DO NOT
unroll the screen surface at this time.

2. Slide the frame pieces together at corners. (Note:
Frame assembly holes may not appear to fit properly
at the corners until all fasteners have been attached.
Once fasteners are attached, the frame corners will
be drawn in for a proper fit.) Secure frame pieces
with #10 screws provided. Do not tighten screws
until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”.
Be sure the frame pieces are assembled according to the
labels. This will ensure the snap pattern on the frame and
screen surface will match.

HIGH POWER

®

FRAME BRACKET

Screens with High Power® viewing surface quantity = 2
Screens with 2-piece side frame rails quantity = 2
Screens 10' to 16' viewing width = 2

QUANTITY INCLUDED ________________________________

SNAP STUD

TOP

SNAP STUD

#10 BLACK SCREW

SIDE

SIDE

FIGURE 1. REAR VIEW

1

BOTTOM

INSTALLATION

There are four methods of installation based on the size
of the screen and type of viewing surface. Measure the
width of the viewing area of your screen and refer to the
appropriate method of installation below. The wall
bracket diagram shows the type and quantity of bracket
that is supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power® viewing
surface.

METHOD 1 (SCREENS 80" AND SMALLER IN
VIEWING WIDTH)

1. Use the supplied #10 screws to attach three frame
brackets to the back of the frame as shown in Figure

2.

FRAME BRACKETS
3-PIECES

LARGE WALL
BRACKET
1-PIECE

#10 SCREWS
6-PIECES

FIGURE 2

2. Secure the large wall bracket to wall studs at the
desired height. Make sure the bracket is level. The
top of the frame will be 1/8" above the top of the wall
bracket when mounted. You will need at least 5/8"
clearance above the bracket to hang the screen.

3. To install the small wall bracket, you must measure
the overall height of the screen frame and subtract
1-3/8". Using that dimension, measure down from the
top edge of the large wall bracket and mark the wall
for two screw holes. The holes should be centered
within the frame and 6" apart. Refer to Figure 3.

SMALL WALL BRACKET
1-PIECE

METHOD 1 (SCREENS 80" AND SMALLER IN
VIEWING WIDTH)

OVERALL

HEIGHT

FIGURE 3

4. Attach the small wall bracket to the wall. Refer to
Figure 4 for proper orientation. Do not tighten the
screws completely. The bracket should slide up and
down easily.

5. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the inside of
the roll. Place the frame over the screen surface, and
while lifting the frame with one hand, snap the
screen surface onto the frame with the other hand
while maintaining a steady pull on the surface.

6. Hang the screen on the brackets by hooking the
bottom of the frame onto the small wall bracket and
lift up until you can hook the top of the frame on the
top bracket. Push down on the frame to seat it on the
brackets. Refer to Figure 4.

OVERALL HEIGHT - 1-3/8"

6"

3

WALL

LIFT

2

FIGURE 4

1

2

METHOD 2 (SCREENS OVER 80" UP TO 96" IN VIEWING WIDTH)

1. Use the supplied #10 screws to attach four frame
brackets to the back of the frame as shown in
Figure 5.

FRAME BRACKETS
4-PIECES

LARGE WALL
BRACKET
2-PIECES

#10 SCREWS
8-PIECES

FIGURE 5

2. Secure the wall bracket to wall studs at the
desired height. Make sure the bracket is level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.

3. To install the lower wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See Figure 6.

FIGURE 6

5. Position the screen with the attached surface
onto the top wall bracket as shown in Figure 7.
Push down at the center of the bottom frame rail
to hook onto the lower wall bracket.

1

FIGURE 7

WALL

2

OVERALL HEIGHT

WALL

OVERALL HEIGHT -1/4"

4. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.

3

METHOD 3 (SCREENS OVER 96" IN VIEWING
WIDTH)

1. Use the supplied #10 screws to attach six frame
brackets to the back of the frame as shown in
Figure 8.

2. Secure the wall brackets to wall studs at the
desired height. Make sure the brackets are level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.

3. To install the lower wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See Figure 6.

4. For 150", 180", 200", 220" and larger screens with
2-piece side frame rails you will will need to
attach one High Power® bracket to each side
frame rail. Use the black #10 screws supplied.
See Figure 8.

FRAME BRACKETS
6-PIECES

HIGH

®

LARGE WALL
BRACKETS
3-PIECES

#10 SCREWS
12-PIECES

FIGURE 8

5. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.

6. Position the screen with the attached surface
onto the top wall bracket as shown in Figure 7.
Push down at the center of the bottom frame rail
to hook onto the lower wall bracket.

7. If you attached brackets to the side frame rails in
step 4, anchor these to the wall with an
appropriate fastener for your type of wall.

POWER
BRACKET
FOR
LARGE
SPLIT
FRAMES,
AND 150",
180", 200"
AND 220"
DIAGONAL
SCREENS.
2-PIECES

METHOD 4 (HIGH POWER® FABRIC)

1. Use the supplied #10 screws to attach two frame
brackets and two High Power® brackets to the
back of the frame as shown in Figure 9.

FRAME BRACKETS
2-PIECES

LARGE WALL
BRACKET
1-PIECE

#10 SCREWS
8-PIECES

®

HIGH POWER
2-PIECES

FIGURE 9

2. Secure the large wall bracket to wall studs at the
desired height. Make sure the bracket is level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.

3. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.

4. Position the screen with the attached surface
onto the top wall bracket as shown in Figure 7.
Push down at the center of the bottom frame rail
to tension the fabric. Mark the screw holes for
the bottom brackets. Drill holes in wall and attach
the brackets to the wall with screws.

BRACKET

4

CLEANING

Da-Tex®, Dual Vision, Pearlescent, Cinema Vision, High
Power®, Da-Mat®, High Contrast Da-Mat®, Audio Vision, High
Contrast Audio Vision, High Contrast Cinema Vision and High
Contrast Cinema Perf surfaces can be cleaned as follows:

Using a white clean cloth (100% cotton preferred) that is
dampened with clear water, gently wipe the area in one
direction. Do not use a circular motion. Using a dry
100% cotton cloth, wipe dry after each cleaning session.
To clean a stubborn stain or a sticky surface, use
denatured alcohol (methanol or methyl alcohol) following
the same procedure as for water.

5

THIS PAGE IS INTENTIONALLY LEFT BLANK

6

LIMITED ONE YEAR WARRANTY

ON DA-LITE PRESENTATION PRODUCTS

Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from
defects in materials and workmanship for a period of one (1) year from the date of purchase by
the original purchaser provided they are properly operated according to Da-Lite’s instructions and
are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental
damage, or which has been tampered with or repaired by a person other than authorized Da-Lite
personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)
the defective part of the merchandise. Returns for service should be made to your Da-Lite
dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation
expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for
damage in shipment. To protect yourself against damage or loss in transit, insure the product and
prepay all transportation expenses.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any

implied warranties of fitness for use, or merchantability, that may be mandated by statute or
rule of law are limited to the one (1) year warranty period. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state-to-state. NO LIABILITY

IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN
OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL
DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may
contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, [phone], (800) 622-

3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH
DA-LITE’S WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Printed in U.S.A. 75135 Rev. 1/087