Dalian Seaside Door Controlling System 9357 User Manual

GARAGE DOOR OPENER

Models 9357·9367

For Residential Use Only

Owner’s Manual

 Please read this manual and the enclosed safety materials carefully!
 Fasten the manual near the garage door after installation.

 The door WILL NOT CLOSE unless The safety is connected and properly aligned.

 Periodic checks of the opener are required to ensure safe operation.

 The model number label is located on the left side panel of your opener

www.seaside.net.cn DALIAN SEASIDE DOOR CONTROLLING SYSTEM CO.,

LTD.

TABLE OF CONTENTS

Introduction 2-6
Assembly 7-9
Installation 10-18
Install The Wall Control 19-20
Install The Photo Eye Safety System 21-22
Power 23-24
Adjustments 24-28
Operation 29
Wall Control 30
Remote Control 30
To Erase the Memory 30
To Open the Door Manually 31
Maintenance 31
Repair Parts 32-33
Troubleshooting 34

1

INTRODUCTION

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to

the possibility of serious injury or death if you do not comply with the warnings that accompany them.

The hazard may come from something or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to
your garage door and/or the garage door opener if you do not comply with the cautionary statements

that accompany it. Read them carefully.

WARNING WARNING

Mechanical Electrical

CAUTION

Check your garage door

1 Disable locks and remove any ropes connected to the garage door.
2 Lift the door halfway up. Release the door. If balanced, it should stay in place, supported entirely by its springs.
3 Raise and lower the door to check for binding or sticking. If your door binds, sticks, or is out of balance, call a trained door
systems technician.
4 Check the seal on the bottom of the door. Any gap between the floor and the bottom of the door must not exceed 1/4 inch
(6 mm). Otherwise, the safety reversal system may not work properly.
5 The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of
the header bracket, it may be installed within 4 feet (1.2 m) to the left or right of the door center. See Installing the Header
Bracket section.

To prevent possible SERIOUS INJURY or DEATH:

 ALWAYS c all a trained door systems technician if

 NEVER try to loosen, move or adjust garage door,

 Disable ALL locks and remove ALL ropes

To prevent damage to garage door and opener:

 ALWAYS disable locks BEFORE installing and

 ONLY operate garage door opener at 120V, 60 Hz to

garage door binds, sticks, or is out of balance. An
unbalanced garage door may not reverse when
required.

door springs, cables, pulleys, brackets or their
hardware, ALL of which are under EXTREME
tension.

connected to

operating the opener.

avoid malfunction and damage.

WARNING

CAUTION

WARNING

To reduce the risk of injury to persons
Use this operator only with Sectional Door.

2

Tools needed

During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.

3

Overview/Carton Inventory

GARAGE DOOR OPENER ASSEMBLY

A

B

C

D

A. Header bracket
B. Pulley assembly
C. Door bracket
D. Curved door arm
E. Straight door arm
F. Trolley assembly
G. Emergency release rope and handle
H. Rail
I. Rail Connectors(2)
J. Hanging brackets（2）
K. Garage door opener
L. “U” rail clips（3）
M. Safety reversing sensors
N. Chain
O. Sprocket and sprocket holder assembly
P. Wall Control Panel
Q. Safety labels and literature

I

H

F

L

G

E

M

N

O

K

Q

J

P

Overview/Carton Inventory

4

ASSEMBLY HARDWARE

N

H1 Clevis Pin, long

Φ8×80 (1)

H4 Hex Bolt M8×20(4)

H7 Lag Screw M8×40 (4) H8 Self-Threading Screw (2)

H2 Clevis Pin,short

Φ8×30 (2)

H5

CotterΦ2×25(3)

H3 Hex

M8(4)

H6

ut

Screw M5×20(2)

Overview/Carton Inventory

5

INCLUDED ACCESSORIES

Wall Control Panel

NOTE: Accessories will vary depending on the garage door opener model purchased. Depending on your specific model,

other accessories may be included with your garage door opener. The instructions for these accessories will be attached to

the accessory and are not included in this manual. The images throughout this manual are for reference and your product

may look different.

Wall Control Hardware

Drywall Anchors (2) Screw M4×30 (2)

Remote Control

ASSEMBLY

6

1、Assemble the Rail

To avoid installation difficulties, do not run the garage door opener until instructed to do so.

To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail

1.1 Carefully remove the hanging brackets , sprocket and sprocket holder assembly packaged inside the rail.

1.2 Align the rails on a flat surface as shown. The front rail has seven holes
connectors.

The behind rail has three holes near the end of rail.

1.3 Pull the rail connectors to the “U” hole position in the rail as shown(1).

1.4 Slide the front rail

into the rail

connector. Bend the “U”.

1.5 Pull out the chain, The chain and sprocket assemble together.

1.6 Slide the behing rail

into the rail

connector. Bend the “U”.

1.7 Fasten the sprocket and sprocket holder assembly with the screws (H6).

Hanging brackets

Sprocket and sprocket holder assembly

Middle Rail

1

2

CAUTION

near the

Rail connector

7

pulley assembly

3

4

Front

Rail

Behind Rail

. The middle rail has two

rail

6

2、Tighten the Chain

2.1 To increase the tension and tighten the chain,turn the

tension nut clockwise or adjustable wrench until the nut is

spaced properly from the rail end -plate.

2.2 Once the nut is spaced correctly,any additional tightening

will overtighten the chain and may cause damage to the

system.

2.2 To loose the tension,turn nut counterclockwise.

2.5cm

H6

5

ASSEMBLY

8

3、Fasten the Rail to the garage door opener

To avoid SERIOUS damage to garage door opener,

use ONLY those bolts/fasteners mounted in the top of the
opener.

3.1 Position opener with light facing front of garage. Rest opener head on cardboard or protective surface on floor so opener

does not get scratched.Chassis side of opener facing up.

3.2 Position rail onto opener chassis by lining uo rail sprocket,Make sure shaft insert into rail sprocket.Press rail down firmly

onto shaft and opener chassis. DO NOT HAMMER.

3.3 Remove the four bolts(H4) from the chassis of the garage door opener.

3.4 Position 2 “U” rail clips over rail and onto chassis. Insert 4 hex bolts(H4) through rail clips holes and into chassis holes. and

tighten hex bolts firmly to hold rail to the garage door opener head.

1

3

H4

5

H4

CAUTION

H4

H4

2

4

“U” rail

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

9

WARNING

To reduce the risk of SEVERE INJURY or

DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND
INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage
door.and lubricated garage door. An improperly balanced door may NOT reverse
when required and could result in SEVERE INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a
trained door systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE

installing
opener to avoid entanglement.

5. Install garage door opener 7 feet (2.13 m) or more above floor.

6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the

floor
and avoiding contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing or servicing opener.
They could be caught In garage door or opener mechanisms.

9. Install wall-mounted garage door control:

· within sight of the garage door.

· out of reach of children at minimum height of 5 feet (1.5 m).

· away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control.

INSTALLATION

1、Determine the Header Bracket Location

10