Dali Ikon 5 Owners manual
951006-0-0 C
IKON
manual
®
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: RISK OF ELECT RIC SHOCK DO NOT O PEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE BACK PANEL. NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
The lightning flash within an equilateral
triangle is intended to alert you to the presence of uninsulated „dangerous voltage“
within the product’s enclosure that may be of
suffi cient magnitude to constitute an electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool and the like.
6. Carts and Stands - The appliance should be used only with a cart or stand if recommended by the manufacturer.
7. Wall or Ceiling Mounting - The appliance should be mounted to a Wall or ceiling only as recommended
by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or position does not interfere with proper ventilation.
For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation
openings; or placed in a built-in installation, such as a bookcase or cabinet, that may impede the fl ow of air through the
ventilation openings.
9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances
that produce heat.
10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instruc tions or as marked on the appliance.
11. Power Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed on or against them, paying particular attention to cords at plugs, convenience receptacles and the point where they
exit from appliance.
12. Cleaning - Do not use any liquid cleaners. Use only a dry cloth to wipe off dust and grease.
13. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period
of time.
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through openings.
15. Damage Requiring Service - The appliance should be serviced by qualifi ed personnel when:
a) The power-supply cord or the plug has been damaged; or
b) Objects have fallen, or liquid has been spilled into the appliance; or
c) The appliance has been exposed to rain; or
d) The appliance does not appear to operate normally, or exhibits a marked change in performance; or
e) The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described in the opera ting instructions. All other
servicing should be referred to qualifi ed service personnel.
2
Contents
Page
Danish Audiophile Loudspeaker Industries .................................................................. 4
Unpacking .................................................................................................................... 5
Break-in ........................................................................................................................ 7
Setup - wide dispersion ............................................................................................... 7
Placement .................................................................................................................... 8
Placement of IKON V
Wall-mounting the IKON 1 & O
Connection ................................................................................................................... 11
Single wiring - IKON 1, O
Bi-wiring - IKON 2, 5, 6, 7, V
Connection of DALI IKON S
Connection to surround amplifi er with separate subwoofer output .............. ..... 13
Connection to a stereo pre-amplifi er .................................................................. 14
Level adjustment ................................................................................................. 15
The listening room ....................................................................................................... 17
Power and acoustic pressure ....................................................................................... 18
DALI - more than meets the eye .................................................................................. 19
Tips and advice from DALI ........................................................................................... 20
Cleaning and maintenance ........................................................................................... 20
Technical specifi cations ............................................................................................... 21
OKAL ............................................................................................. 9
N WALL ........................................................................... 10
N WALL, VOKAL 1 ..................................................................... 12
OKAL 2 ............................................................................... 12
UB ...................................................................................... 13
3
Danish Audiophile Loudspeaker Industries
Thank you for selecting DALI IKON loudspeakers.
It is important to us that your new DALI loud-
speakers are set up and connected optimally. For
this reason, we recommend that you read this
manual and follow its instructions.
This manual contains instructions for setup and
connection, as well as tips and advice on how
to get the most out of your new loudspeakers.
Remember to sign up for our e-mail newsletter
at www.dali.dk.
DALI is acclaimed around the world for unique
loudspeakers built to our uncompromising stand-
ards for design and performance.
The goal for every single DALI loudspeaker is
always our foremost commitment: To create a
listening experience in your home that will make
you forget time and place.
Enjoy.
4
Unpacking
Unpacking:
Carefully unpack the loudspeakers of the box.
Dependant on which DALI IKON model you have
bought, different accessories comes with the
loudspeaker, which you can read about in the fol-
lowing chapters.
Grille fronts:
The speakers are delivered with the grille fronts
already mounted when you unpack them. If you
wish to remove the grille f ront, loo sen it by gra du-
ally tugging at the 6 metal plungers that hold it
in place. It is important that all 6 are equally loos-
ened before removing the front. Otherwise, the
grille may be damaged.
Tool kit for IKON S
UB
1. M8 nut, 4 pcs.
2. Rubber foot, 4 pcs.
3. M8 spike, 4 pcs.
4. 13 mm fork wrench, 1 pc.
Tool kit for IKON 5, 6, 7
1. Aluminium foot, 4 pcs.
2. M8 screw, 4 pcs.
3. M8 nut, 4 pcs.
4. Rubber foot, 4 pcs.
5. M8 spike, 4 pcs.
6. 5 mm Allen key, 1 pc.
7. 13 mm fork wrench, 1 pc.
2
3
4
5
Figure 2 . Tool kit for I KON 5, 6, 7
Tool kit for IKON 1, 2, V
OKAL 2, ON WALL
V
1: Bumper, 4 pcs.
7
6
1
OKAL 1,
2
1
3
Figure 1. Tool ki t for IKON S UB
4
1
Figure 3. Tool kit for IKON 1, 2, V
V
OKAL 2, ON WALL
OKAL 1,
5
Spikes:
On some fl oor surfaces and in some rooms,
the use of spikes is a crucial aspect of obtain-
ing the best result. The spikes (included)
should be screwed in loosely in the four
aluminium feet, leaving the spike’s nut only
slightly tightened. Using the screws (included),
mount the feet in the threaded holes in the
bottom of the speaker. Push the feet against the
cabinet before tightening the screw.
Place the loudspeaker upright on its spikes on the
fl oor, so that it stands steadily without rocking.
Tighten the nuts, so that the four spikes sit tightly
in the aluminium feet. These assembly and setup
steps ensure stable mechanical coupling to the
surface beneath.
Rubber feet:
The enclosed rubber feet may be used instead
of spikes. The rubber feet can be mounted on
the aluminium feet over the thread holes for the
spikes.
Figure 4 . Mounting spikes
6
Break-in
Like any mechanical system, a loudspeaker
requires a “break-in” period. You will experience
a gradual increase in sound quality during an ini-
tial period. Unlike other mechanical systems, the
lifespan of a loudspeaker is increased by regular
use.
Setup - wide dispersion
DALI IKON is a prime exponent of one of the many
virtues that have made DALI famous worldwide
– Wide Dispersion.
Wide Dispersion means that the area in front of the
loudspeakers where a full stereo image is achieved
is a great deal wider than with other loudspeak-
ers. This ensures substantially better sound across
a larger area within your listening room.
Figure 5. DALI IKON b ass driver
To take full advantage of DALI IKON’s Wide Dis-
persion, the loudspeakers should face straight
ahead and not be angled in towards the listening
position unless the two loudspeakers are placed
very far apart.
The IKON tweeter module is especially developed
for this loudspeaker. Its unique design ensures that
Wide Dispersion is more than just a name – you
can tell the difference.
Figure 6 . DALI IKON H igh fre quency mod ule:
Soft d ome tweeter and ribbon tweeter
7
Loading...