FLR3-100 Installation Quick Guide Page 1 of 5
Antenna Hole Plug
AH
Mounting Stud
Receiver
Antenna
Mounting Stud
Nut
Digit Face
Nut
Washer
Receiver
This quick guide provides steps for installing the receiver and setting up a FLR3-100 key fob with a
FuelightTM Gen 3 display.
Installing the Receiver
1. Using a flat-head screwdriver, open the digit face to
access inside the digit cabinet.
2. Remove both antenna hole plugs from the digit face.
Refer to Figure 1.
3. Place the receiver on to the mounting studs on the back
of the digit face. Refer to Figure 2.
4. Use a 5/16" nut driver to secure the receiver to the
mounting studs using the two provided nuts.
5. Place the threaded end of the antenna cable through
Figure 1: Digit Door Receiver Mounting Overview
the antenna hole.
6. Place the flat washer over the threaded end of the antenna cable.
Refer to Figure 2.
7. Thread the provided nut on to the threaded end of the antenna
cable and tighten using an 11/32" wrench.
8. Thread the female end of the antenna on to the threaded end of
the antenna cable and turn the antenna clockwise until snug. Refer
to Figure 2.
9. Connect the receiver cable from receiver to the driver. Refer to
Figure 3.
10. Neatly secure any excess cable with cable ties.
11. Close and secure the digit face.
Figure 2: Mounting Prole
Driver
Figure 3: Final Receiver Assembly
DD2291475 Rev 05
6 August 2014
Antenna Cable
PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128
tel: 800-325-8766 fax: 605-697-4700
www.daktronics.com
Digit Cabinet
FLR3-100 Installation Quick Guide Page 2 of 5
LL-2855 REV00
CONFIG
ADDR
SYNC
4
3
2
LINE
1
TEST
1 2 3 4 5 6 7 8 9 0
ON
1 2 3 4 5 6 7 8 9 0
ON
Setting the Security DIP Switches
The FLR3-100 key fob has a series of dip switches on the back to give it a unique address setting. Set these
switches to a unique setting to prevent others from being able to control your display.
1. Remove the small cover on the back of the FLR3-100 key fob radio. Refer to Figure 4.
2. Using a paper clip or a micro screwdriver, set the switches to a unique setting.
Note: Do not change switches nine and zero.
3. Replace the back cover.
Mating the Key Fob with the Display
Follow these steps to mate the display with the FLR3-100 key fob. If these steps are not completed, the
display will not recognize
or respond to the key fob.
1. Turn power on to
the display.
2. While display is
booting up, or
within 5 minutes,
press and hold
Line one Plus
(+) and Minus
(-) keys until the
decimal flashes
3 times. Refer to
Figure 4.
Figure 4: FLR3 Key Fob
3. Once the decimal
point flashes 3 times, release the buttons.
Setting the Display Line Numbers
Follow these steps to map the line number for each display. It is important that each display is set for the
correct line number for it to show the correct price.
1. Make sure the display is turned on.
2. Press and hold the -2 and +2 buttons on the key fob until the host display face begins to dim and
brighten or the decimal begins to flash. This takes about five seconds.
Note: The host display is the display with the radio antenna connected to it.
DD2291475 Rev 05
6 August 2014
PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128
tel: 800-325-8766 fax: 605-697-4700
www.daktronics.com
FLR3-100 Installation Quick Guide Page 3 of 5
3. While the display slowly flashes, press the +2 button until the appropriate line number is shown
on the display (L01, L02, etc).
4. Once the line number is set, press and hold the -2 and +2 buttons until the next display face
begins to slowly flash.
5. Repeat these steps until all display faces have been correctly mapped.
Note: If a display gets set incorrectly, complete the process with the remaining displays then
repeat to correct.
6. Exit configuration mode by pressing and holding the -2 and +2 buttons until the displays show
prices and they no longer flash; about five seconds.
Note: All displays are programmed with a default price matching their line number. Use this to
easily identify that all displays are addressed correctly.
Number Conguration
This section steps you through configuring the numbers six
and nine and the fraction display preferences.
1. Make sure display is turned on.
2. Press and hold the -3 and +3 buttons on the key
fob until all displays show the numbers 6 and 9.
The number scheme will be either 3.69 9/10 or 4.69
9/10. Refer to Figure 5.
3. Press the Plus (+) or Minus (-) keys to scroll
through the different configuration options.
Note: For Domestic displays with a 9/10s digit, the
number 3 needs to show in the first column for the
desired format. For International displays, make
sure the number 4 shows in the first column for the
desired format.
International displays offer two configuration
options - tails and 9 and no tails and 9, as shown
in Figure 6.
Tails and 9/10
Tails and 9
No Tails and 9/10
No Tails and 9
Figure 5: Digit Congurations
Tails and 9
4. When the desired configuration is shown on the
displays, press and hold the -3 and +3 buttons to
exit configuration mode.
DD2291475 Rev 05
6 August 2014
PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128
tel: 800-325-8766 fax: 605-697-4700
www.daktronics.com
No Tails and 9
Figure 6: International Digit Conguration
FLR3-100 Installation Quick Guide Page 4 of 5
Entering Test Mode
Entering test mode causes the displays to cycle through various pieces of information that can be useful
when working with Daktronics Technical Support.
1. Press and hold the Plus (+) and Minus (-) keys on line four of the key fob until the displays begin
cycling through test mode.
2. Exit test mode by pressing and holding the Plus (+) and Minus (-) keys on line four until the
displays return to showing prices; approximately five seconds.
DD2291475 Rev 05
6 August 2014
PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128
tel: 800-325-8766 fax: 605-697-4700
www.daktronics.com
AH
BLK
WHT
GRN
TB3-2
TB3-3
TB3-4
JBX2 WIRING TABLE CABLE E
G
DRIVER
FUELIGHT DISPLAY
REC
B
C
OVERALL SIGN STRUCTURE
ANT
TB3-1 RED
DRIVER
A
MD
MAIN DISCONNECT
D
E
JBX2
DAKTRONICS CUSTOMER
CABLE IDENTIFICATION TABLE
COMPONENT IDENTIFICATION TABLE
OPTIONAL JBOX, DIRECT ACCESS PORT
COMPONENT DESCRIPTION PROVIDED BY INSTALLED BY
DRIVER FUELIGHT DRIVER DAKTRONICS FACTORY
MD MAIN DISCONNECT CUSTOMER CUSTOMER
KEYFOB REMOTE KEYFOB REMOTE DAKTRONICS CUSTOMER
REC KEYFOB REMOTE RECEIVER DAKTRONICS CUSTOMER
JBX2
ANT KEYFOB REMOTE RECEIVER ANTENNA DAKTRONICS CUSTOMER
CTRL OPTIONAL WIRED DM-100 PRICE/T&T CONTROLLER DAKTRONICS CUSTOMER
ID TAG DESCRIPTION PROVIDED BY INSTALLED BY
DAKTRONICS CUSTOMER
DAKTRONICS CUSTOMER
DAKTRONICS CUSTOMER
OPTIONAL QUICK CONNECT PNL MNT TO 6 POS MINI MNL, 8FT
CABLE:ANTENNA:RP-SMA FEM BULKHEAD TO RP-SMA MAL,12
HARN; 6 PIN MINI MNL TO 6 PIN MINI MNL, 5FT
A
B
C
DAKTRONICS CUSTOMER
DAKTRONICS CUSTOMER
DAKTRONICS CUSTOMER
CABLE; RS232 DB9 MALE TO DB9 FEMALE, 10FT
POWER FEEDER SEE NOTE "1" CUSTOMER CUSTOMEREHARN; 6 POS QUICK CONNECT TO WHIP, 50FT (NOT INCLUDED)
D
CABLE; LINE TO LINE; 4 POS MINI MNL, 15 FT
F
G
100FT MAX
02 20 SEP 2013 JJL
01 14 AUG 12 LCS
DD2291475 Rev 05
6 August 2014
KIT
SEE NOTE 4C
(NOT INCLUDED)
SEE NOTE 4 A&B FUELIGHT DISPLAY
SYNCADDRCONFIGTEST
321
LINE
ADDED JBX WIRING TABLE
REVISED JBOX NAMING AND MADE DISPLAYS SOLID LINES
DIRECT ACCESS PORT
LL-2855 REV00
4
(INCLUDED)
KEYFOB REMOTE
CTRL (SEE NOTE 4D)
PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128
tel: 800-325-8766 fax: 605-697-4700
F
ALL WIRING TO MEET OR EXCEED LOCAL AND
2. 2 KNOCKOUTS PROVIDED FOR 3/4" CONDUIT
NATIONAL ELECTRICAL CODES.
1. POWER FEEDER SIZED AS NEEDED, BY CUSTOMER.
NOTES:
GEN III FUELIGHT
RISER DIAGRAM; FLR3-100
LSOPER
NONE
1 OF 1
www.daktronics.com
4A. INSTALL OPTIONAL QUICK CONNECT PANEL IN
THE SIGN STRUCTURE NO MORE THAN 8 FEET FROM
THE DISPLAY DRIVER. DRILL 7/8" HOLE IN SIGN
4B. RUN OPTIONAL QUICK CONNECT CABLE
TABLES FOR WIRE TERMINATIONS.
3. REFER TO MANUAL FOR LINE-TO-LINE WIRING
SIGNAL ENTRANCE.
BETWEEN DISPLAYS.
FITTING ON REAR OF DISPLAY FOR POWER AND
STRUCTURE TO PASS CONNECTIONS THROUGH. USE
INCLUDED BUSHINGS WHERE APPLICABLE.
4C. OPTIONAL DIRECT ACCESS PORT KIT NOT
CONDUIT TO THE SIGN STRUCTURE. SEE JBX WIRING
PROVIDED WITH DIRECT ACCESS PORT THROUGH 3/4"
INCLUDED IN FLR3-100 KIT.
LSOPER 11 APR 12
02
P1611 F
01 A
4D. OPTIONAL WIRED CONTROLLER NOT INCLUDED IN
4E. JBX2 CONNECTION IS NOT TO BE USED WITH A
5. SEE DWG-1092852 FOR OPTIONAL DIRECT WIRED
6. ADDITIONAL PYLONS REQUIRE ADDITIONAL
FLR3-100 KIT OR DIRECT ACCESS PORT KIT.
COMM OPTION AND WIRING DIAGRAM.
LAPTOP.
FLR3-100 KITS.
1093014
Loading...