Dake 985017-1 User Manual

Operator’s Manual and Part’s List

Model J-10 & JH-10

Dake/Johnson Horizontal Bandsaw

6/02

DAKE Division of JSJ
724 Robbins Road
Grand Haven, MI 49417
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
[e-mail]
Web: www.dakecorp.com

1

6/02

NOTE:

FOREWORD

This manual has been prepared to acquaint you with the operation, maintenance, and
serviceable components of your Dake/Johnson machine. We urge that you read it carefully
before operating your machine. Please refer to the pertinent sections when contacting the
factory regarding parts, schematics…or when you have other questions.

As Dake’s policy is one of continuous development for each range of machine, the contents
of this manual, though completely up to date when issued, are subject to change without
notice.

For your information and future reference, pertinent data concerning your machine may be
inserted in the space provided below.

Machine Model ___________________________

Serial Number ___________________________

Date Received _________________

Voltage ___________________________

Phase _______ Cycle _______ Motor H.P. ______

Please give the machine model and serial number in correspondence, and include the parts
numbers on parts orders to speed the filling of your requirements and to minimize your
inconvenience.

FACTORY: DAKE Division of JSJ

724 Robbins Road
Grand Haven, MI 49417
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
[e-mail]
Web: www.dakecorp.com

substitutes or imitations may cause damage to the machine, void the warranty, and may
cause injury.

Use only genuine Dake/Johnson replacement parts and optional equipment. Use of

2

CONTENTS

GENERAL

Basic Machine Data ……………………………………. 4
Specifications …………………………………………….. 4

Machine Installation ……………………………………… 4
Safety Information………………………………………… 5-6

Electrical Diagrams ………………………………………. 7-9

Machine Features ……………………………………….. 10

SECTION 1

OPERATION

Controls and Operation ………………………………….. 11
Standard Drive …………………………………………… 12
Blade Selection ………………………………………….. 13
Blade Removal/Installation ……………………………… 13-14
Blade Guide Adjustment ………………………………… 14-15
Balance Spring Adjustment …………………………….. 15
Feed Cylinder Bleeding …………………………………. 15

SECTION 2

MAINTENANCE

Lubrication ………………………………………………… 16
Sawing Problems and Solutions ………………………… 17

SECTION 3

ASSEMBLIES & PARTS LISTS

Machine Assembly (Front View) ………………………… 18-19
Machine Assembly (Top View) ………………………….. 20
Gear Box Assembly ………………………………………. 21
Hydraulic Assembly ………………………………………. 22-23
Guide Arm Assembly ……………………………………... 24
Vise Unit ……………………………………………………. 25

6/02

3

6/02

BASIC MACHINE DATA

SPECIFICATIONS

Capacity………...10” (25cm) rounds, 18” (46cm) flats Floor Space ……………… 29” (74cm) x 70” (178com)

Blade Size (Part Numbers: 75958 (3/4”) OR 75957 (1”) Height, Closed* …………………………….. 39” (99cm)

J-10 ……………………… ¾” (2cm) x 137” (348cm) Height, Open* ……………………………... 64” (163cm)
JH-10……………………... 1” (3cm) x 137” (348cm) Floor to Bed* …………………………….. 23 ¾“ (60cm)

Blade Speeds Net Weight

………………………………50, 90, 160 and 270 fpm

………………………………..15, 29, 49 and 82 mpm
Bed Work Area. ……..……… 11” (28cm) x 18” (46cm)
Vise Size ………………………. 5” (13cm) x 11” (28cm)

Drive Motor Gross Weight

J-10 ………………………………….…. 1 hp (.75kw)
JH-10 …………………………………... 1 hp (.75kw)

Electrical System, specify …....110/230V, 1 PH, 60 Hz

208/230/460V, 3 PH, 60 Hz

Coolant Capacity …………………………...… 3 gallons Water-soluble only – do not use oil.

INSTALLATION

UNCRATING :

machine has been moved to its approximate location.

CAUTION: BE SURE ELECTRICAL CHARACTERISTICS OF MOTOR AND SWITCH
CORRESPOND WITH ELECTRICAL POWER SUPPLY.
!!!ATTENTION!!! DO NOT ATTEMPT TO RUN THIS SAW UNTIL THE BLADE ALIGNMENT HAS
BEEN CHECK AS PER THE OWNER’S MANUAL AND THE BLADE HAS BEEN PROPERLY RE­TENSIONED.

LEVELING:

should be more carefully leveled to be certain that the coolant intake remains submerged.

CONNECT INCOMING POWER TO THE STARTER PER APPLICABLE DIAGRAM, AND IN
ACCORDANCE WITH ALL LOCAL CODES.

Remove crating carefully. For ease in handling do not remove from skid until

Position machine reasonably level, shim under legs if necessary. Wet machines

J-10 Dry …………………………. 812 lbs (368 kgs)
J-10 Wet ..……………………….. 845 lbs (383 kgs)
JH-10 Dry ……………………..… 817 lbs (371 kgs)

JH-10 Wet ……………………….. 850 lbs (386 kgs)

J-10 Dry …………………….…… 896 lbs (406 kgs)
J-10 Wet ……………………..….. 929 lbs (409 kgs)
JH-10 Dry …………………..…… 901 lbs (409 kgs)

JH-10 Wet ..……………………….934 lbs (424 kgs)

4

SAFETY INFORMATION

LABEL

84605

LABEL

84604

LABEL

84395

LABEL

76462

LABEL 84605 – SAFETY INSTRUCTIONS

6/02



 When

you see this symbol on your saw, be alert to
the potential for personal injury.

Follow recommended precautions and safe
operating practices. Carefully read all safety
messages in these instructions and on your saw
safety signs. Keep safety labels in good
condition. Replace missing or damaged safety
labels.

5

LABEL 76462 – SAFETY INSTRUCTIONS LABEL 84395 – DANGER LABEL

LABEL 84604 – WARNING

Follow recommended precautions and safe operating
practices. Carefully read all safety messages in these
instructions and on your saw safety signs. Keep safety
labels in good condition. Replace missing or damaged
safety labels.

6/02



 When you see this

symbol on your saw, be alert to the potential for
personal injury.

6

ELECTRICAL CONTROL DIAGRAMS

6/02

7

SINGLE PHASE ELECTRICAL DIAGRAM

6/02

8