Dake 977600-1 User Manual

TB & SB Series Drill Presses

OWNERS MANUAL

BENCH AND FLOOR DRILL PRESS
TB-16 Series & SB-16-25-32-Series

FOR YOUR OWN SAFETY AND
OPTIMUM OPERATION READ
INSTRUCTION MANUAL BEFORE
OPERATING DRILL PRESS
RETAIN THIS MANUAL FOR
FURTHER REFERENCE.

TABLE OF CONTENTS

 Model specifications page 1

 Electrical diagram page 1

 Voltage protection recommendations page 1

 Drill press installation page 2

 Safety points page 3

 Power warning page 4

 General safety instructions page 4-6

 Voltage warning and grounding instructions page 7

 Operation and set-up instructions page 9 –10

 Tooling removal page 11

 Work holding and machine maintenance page 11

 Speed adjustment and belt tensioning page 12

 Proper drill speeds for materials and bit diameter page 13

 Dake safety features page 13

 Exploded diagram TB / SB 16 page 14

 Parts list TB / SB 16 page 15

 Exploded diagram SB 25 / 32 page 16

 Parts list SB 25 / 32 page 17

 Trouble shooting matrix page 18

1

Machine

Specifications:

Drill Type
Max. Drill Capacity
Spindle Taper
Spindle Travel
Max. Work Diameter
Speeds (Step Pulley)
Spindle Speed Range
Column Diameter
Table
Base
Spindle to Table
Spindle to Base
Motor
Electrics
Voltage
Overall Height
Weight

MODEL AND SPECIFICATIONS

Model TB-16 Model SB-16 Model SB-25 Model

Bench Floor Floor Floor

5/8” 5/8” 1” 1-1/4”

MT2 MT2 MT3 MT4

3-1/8” 3-1/8” 5” 5-1/4”

14-1/8” 14-1/8” 18” 18”

9 9 9 9

240-3400 240-3400 270-2000 270-2290

3-1/8” 3-1/8” 3-5/8” 4”

11-3/4 x 11-3/4” 11-3/4 x 11-3/4” 14 x 14” 15-3/4 x 15-3/4”

17-3/4 x 12-1/8” 19-1/2 x 12-1/2” 23-1/2 x 15” 23-1/2 x 15”

16-1/2” 28-1/4” 28-1/4” 26-1/4”
25-1/2” 49” 49-1/8” 50”

½ HP ½ HP 1 HP 2 HP

CE CE CE CE

120 Volt 120 Volt 220 V – 3 PH 220 V – 3 PH

42-1/2” 64” 71” 71”

155 lbs. 210 lbs. 397 lbs. 463 lbs.

ELECTRICAL DIAGRAMS

SB-32

CAUTION

20 AMP circuit breaker is recommended for the TB-16 and SB-16 models.
30 AMP circuit breaker is recommended for the SB-25 110 volt model.

2

1. UNCRATING AND INSTALLATION

INSTALLATION OF DRILL PRESS
MACHINE IS TOP HEAVY!

1. Location of the drill press should be in a well lit area with correct
power supply and that will not interfere with other machines or
operations.

2. Carefully uncrate machine from crate. Inspect all packing as not
to throw out any parts or manuals.

3. When transporting the machine please use caution. If using a
sling have someone steady the machine while transporting it.

4. Install your drill press on a sturdy level floor surface, or work
bench. (TB-16) The machine must be anchored to the floor or
workbench securely. Machine is top heavy.

5. Connect appropriate power to the machine. Make sure circuit
breakers are suitable for the machine. Consult local codes for
proper installation of machine. Always route power cables in a
safe manner away from traffic areas, damp areas, heat and
moving parts.

6. After installing the drill press, use the kerosene or degreasing
product to clean off the anti-rust oil which was applied at the
factory. Then wipe machined surfaces with a light coating of
lubricant oil. (Way oil)

7. Read rest of the owners manual before operating this machine.
Review and understand all safety instructions.

CAUTION

3

 SAFETY POINTS

BEFORE USE, ALL SAFETY POINTS MUST BE READ AND UNDERSTOOD!

Before the DRILL PRESS is used, the instruction manual with this machine must be

read and understood. This manual offers safe operation instructions.
Offered below are safety instructions designed for the drill press and general
safety instructions that apply to most machinery.

Operation of the drill press incorrectly, or in a
dangerous fashion can result in serious injury
or death.

Operation of the drill press incorrectly, or in a
dangerous fashion can result in damage to
machine or it’s components and to the cutting
tool.

Instructions for safe drill press use.

Intend use :
The DRILL PRESS is designed to for drilling or boring operations. Caution is
required when operating the drill press because it can be dangerous due to
the high spindle rotation speed. Operation hazards such as entanglement,
shearing, ejection parts ….etc. Guards such as pulley cover and chuck guard
must in place and working condition to prevent any hazard.
Please think about the safety warnings in the instruction manual before
operating the machine.

4

2. FOR SAFE OPERATION
For your own safety read the instruction manual before operating DRILL
PRESS.

DANGER

HIGH VOLTAGE

TURN OFF THE POWER
BEFORE SERVICE

1. SWITCH the POWER OFF before setting, inspecting
lubricating, cleaning or changing the drill bit.

2. Always wear the eye protection.

3. Do not wear gloves, necktie, necklaces, rings or loose
clothing.

4. To clamp work piece or brace against column to prevent
material rotation.

5. Use recommended speed for drill bit, and work piece
material.

3. GENERAL SAFETY INSTRUCTION

DANGER

1. Keep guards in place and in working order.

2. Remove adjusting key and wrenches. Be in the habit of
checking to see that keys and adjusting wrenches are
removed from tool before turning it on.

3. Keep work area clean. Cluttered areas and benches invite
accidents.

4. Do not use in dangerous environment. Do not use power
tools in damp or wet locations or expose them to rain. Keep
work area well lighted.

5. All visitors should be kept safe distance from work area.

6. Make workshop kid proof with padlocks, master switches, or
by removing starter key.

7. Do not force tool. It will do the job better and safer at the rate
for which it was not designed.

GENERAL SAFETY

INSTRUCTION

5