Daiwa TANACOM 1000 User Manual

OPERATING MANUAL

Thank you for purchasing a TANACOM 1000. To take full advantage of the
reels many useful functions, please read this manual carefully before using. Retain
this manual for future reference.

Reference

Reference

Index

Caution

  Precautions

Power source

How to connect the reel to the power source
  About the power source
  Battery indicator

Using the Reel

  About the counter display

Maintenance

About maintenance
  Maintenance procedure
  Handling and maintenance of the power cord

Maintenance of the power cord
Other maintenance points

Names of the buttons and the display

Names and functions of each part

Line data input
When line length is known---------(P1)

With Backing line---------------------(P2)
 Backing line 2--------------------------(P3)

Functional setting operation
1 Mode setting display
How to set the many functions available

2. Before you begin fishing

  Surface depth setting

  When the main line is cut or broken off.....

3. Auto stop function

Auto stop setting
  Auto stop

4. Line feeding function
Line feeding function

5. Pickup speed setting

  Pickup speed preference

6. Inverse counter

  Inverse counter

7. Jigging

Jigging
  Jigging master

8. Winding speed indicator

 Winding speed display

9. Remaining time to auto stop

  Displaying of the remaining time to auto stop

4,5

6,7

8,9

10-15
10,11
12,13
14,15

16-30
16,17

18

19

20

21

22

23-25

23

24,25

26

27

1

10. Chumming timer winding

Chumming timer winding
  Chumming timer

2

11. Display recalibration

  Display revision

How to fix the Rod Clamp

3

Useful functions

Various alarms
  Display light
  Breaker display

4
4

Reel Specifications

5

  Reel Specification list

5

  Counter display

5

Parts List

Trouble shooting

See animation

Electric reel’s basic

28,29

28

28,29

30

31

32

33

34

35

operations

Caution

Precautions

1. Be careful to keep fingers clear of the levelwind mechanism. It can pinch your fingers
and cause injuries.

Warning

1. If your sinker or lure is caught on the bottom, cut your line rather than jerk the rod to
free it.

2. After fishing, rinse and dry the reel thoroughly. Store in a dry place.

3. Handle the reel with care. Dropping it may cause damage.

4. Do not touch the line while reel is running. It could cut your skin.

5. Use this reel for fishing purposes only.

6. Be careful not to get reel grease on your clothing.

7. Do not use metal wire for the main line.

8. Sharp impacts due to inadvertent drop or other reasons may cause reel body
breakage, damage to the inner electronic components, and cracks or short circuit of the
board, resulting in functional disability.

Attention

1. When you use a power source other than the battery or the power source provided by
the boat, be sure it is of the proper voltage. Excess voltage will harm the reel and may
generate enough heat to burn your hands.

2. Do not use badly rusted cord to prevent electrical heat.

1. Do not touch moving parts while the reel is operating or it may cause injury.

2. Drag adjustment should only be done with the auto winding functions off.

1. Do not disassemble the reel. It could result in malfunction that could damage the reel
or cause personal injury.

About the counter display

The following conditions may make the display difficult to read.

1. Wearing of polarized glasses.

2. Excessively cold or hot weather, mid-winter (displayʼs surface temperature is below -10 degrees
centigrade) and mid-summer (displayʼs surface temperature is above 60 degrees centigrade).

3. When light strikes the display from certain angles, the displayʼs digits may have shadows. This does not
affect its function.

Do not reel in the end of the line

DO NOT allow end of line to be wound onto the spool.This may cause synchronization with the levelwind to
be lost, a condition that can damage the levelwind due to the reelʼs high power output. Should this happen,
line should be removed from spool and rewound.
After each trip, attach line to line clip to prevent it accidentally being wound onto reel.

end of the line

line

snap

1

line clip

Power source

How to connect the reel to the power source

1. Attach the cord clips to the battery. Red covered clip is the plus

(+), and the black covered clip is the minus (-).

2. Insert the connector into the reel. After this,

the display appears as below.

By taking the appropriate steps, the indication

will change as shown below and the data
will be set.

0.5 sec

Red

Black

Match slot
with key

Beep !

All the features light An indication change Set completion

1.When changing batteries, the display’s back up memory stays active for about 15

minutes after the old battery is disconnected. Thus the above display startup sequence

Attention

does not need to
frame.

replay when the new battery is connected within the 15 minute time

About the power source

This reel is made to accept DC 12 Volt power only. Power sources
providing other than this cannot be used.
The power provided by a boat can be unstable, causing the reel to
stop unintentionally.

To make the most of the reels performance, be sure to use the
specified battery for the electric reel.

Make sure of the following before departure.

1. Recharge the battery before your fishing trip. Over time, a battery can naturally discharge.

2. Confirm the boat can provide the proper power source (i.e. voltage, connector shape etc).

Attention

3. Corroded connections can prevent the flow of electric current. Remove any corrosion or
dirt from the connectors.

Battery indicator

With power on, digits of the inverse counter (counter in the lower
area) will blink if voltage gets below DC 9 V.
If the display shows this when the motor is not running, then
battery voltage is likely to be low. In this case, replace the battery
with a recharged one.

2

This figure shows the
voltage is 8.5 V

Using the Reel

1. Do not jerk your rod to free a lure or sinker stuck on the

bottom. Pull the line taught with a gloved hand and cut it.

2. After maintenance, be sure to loosen the drag and store the

reel in a dry place.

3. Handle the reel with care to avoid dropping and possibly

damaging it.

4. Do not use metal wire as the reelʼs main line.

1

2

Tournament
Drag

loosen

About the counter display

The following conditions may make the display difficult to read.

1. Wearing polarized glasses.

2. Excessively cold or hot weather, mid-winter (displayʼs surface

temperature is below –10 degrees centigrade) and mid-summer
(displayʼs surface temperature is above 60 degrees centigrade).

3. When light strikes the display from certain angles, the displayʼs

digits may have shadows. This does not affect its function.

3

Maintenance

About maintenance

This is a washable reel. Wash away salt residue and grit after fishing.

Maintenance procedure

1. Wash the reel with a dish washing detergent and a soft

sponge. Do not use solvents.

Do not use soap or other detergents. Other soaps or solutions

may damage the reel both externally and internally. The
solution may damage the outside coating of the reel and may
breakdown the grease inside of the reel creating an overflow of
grease.

2. Rinse detergent and dirt away with running water, rinsing the

spool very well to get rid of salt. Use warm water, under 30
degrees centigrade.

3. Dry the reel well.

*Loosen the drag when stored.
*Be sure to remove water from inside the handle knob,
because water could build up there.

1. Do not wash with seawater or soak in water.

2. Do not use o

3. Do not use a steel brush or abrasive cleanse

rganic solvents such as benzene and thinner.

Attention

r.

4

Maintenance

Handling and maintenance of the power cord

Follow the restrictions below to avoid cord problems. Do not cut or connect your cord by yourself as it can cause

unintended problems.

Do not hang the reel
by the power cord.

Do not wash the power
cord.

Maintenance of the power cord

- Wipe the power cord with a wet cloth and dry it well.

- Pay special attention to drying the tips, with cover removed.

- Grease the connector after it is dried.

- Disconnect the power cord from the reel before storing.

Do not wind the power
cord around the reel
body with the connector
inserted into the reel.

Do not set heavy items
on the power cord, or
tie knots in the power
cord.

Hold the connector, not the power cord, to pull the power
cord from the reel

Clean and grease area A (pins) and area
B (Circumferential area).

A

B

Other maintenance points

- This reel is a precision instrument that employs electric circuity and motor. Do not disassemble the reel by
yourself.

- Cover the power connector on the reel with its protection cap.

- Old or worn cords can cause a bad connection and/or short circuit. Replace the cord every 2 years.

5

Names of the buttons and the display

MODE BUTTON

1

RESET BUTTON

2

INVERSE COUNTER BUTTON

3

JIG/PICKUP BUTTON

4

Mode display

5

Depth counter

6

Chumming timer

7

(Power indicator,
time to wind up,
timer display)

Jigging display

8

Inverse counter

9

(winding speed display)

6

Names of the buttons and the display

1

 MODE BUTTON

Press the MODE BUTTON to scroll through the adjustment displays for each reel function.

- Use the Power Lever to adjust numeric values.

- Pressing the MODE BUTTON sets the numeric values you have adjusted.

- Depress and hold the MODE BUTTON to return to the depth display.

- Mode change cannot be done while line is being fed.

2

 RESET BUTTON

This button resets the depth counter to zero.
Make sure to press this button before you start fishing. The reset depth is used to make the auto stop function

work. (display shows ). The default setting of auto stop is 2 meters.

This prevents accidental resetting. For a total reset, when line has been broken off, press and hold the button for at

least 2 seconds.

3

 INVERSE COUNTER BUTTON

Pressing this button resets the counter in the lower area of the display.

- It memorizes distance from the bottom, handy for dropping a bait right back into the strike zone after youʼve been
bit.

- The chumming timer resumes after pressing this button.

4

 JIG/PICKUP BUTTON

Selection between pickup and jigging can be done in the mode setting display.(One of them should necessarily be chosen.)

Pickup

-You can wind only while pressing this button. This function is useful to wind up line slack and attract fish.

- Winding speed can be changed with the mode setting display. (Default setting is speed 15)

Jigging

- Jigging can be ON/OFF.

- Pressing this button starts jigging. (Display shows )

- Pressing the button again stops jigging.

5

 Mode display

- This display allows you to change setting of each function.

- The functions that are set to work are shown on the display.(Default setting is speed 15, but the speed can
actually be set between 0~Hi.)

Display

Chumming timer starts working.

Auto Line feeding is employed. Default
setting is off.

Pressing the RESET BUTTON makes this
indicator appear, telling you auto stop will
work.

6

 Depth counter

- It shows the depth from the surface.

7

 Chumming timer (Power indicator, time to wind up, timer display)

- The chumming timer appears when motor rotation is stopped.The timer display cannot be set to OFF.

- While using the power lever, the power level is shown.

- While the electric winding up is in action displaying actual winding speed, the timer indicates the remaining time to
auto stop at the ship side(in minutes and seconds).

8

 Jigging display

- This is appeared only when the jigging function is on.

- It blinks when jigging is in process.

Function

9

 Inverse counter (winding speed display)

- This counter shows the depth from the bottom (or a certain depth).

- Once this counter is turned on, its display cannot be turned off.

- While winding up, winding speed appears in meters per minute.

(The display of winding speed can be set to OFF)

7

Names and functions of each part

Free spool adjustment

weak

loosen

strong

Power lever

tighten

Waterproof drag

Clutch

Enclosed items

Power cord Levelwind threader Rod Clamp 

Levelwind

8

Names and functions of each part

Free spool adjustment

1

- It adjusts brake tension on the spool to prevent backlash or line slack caused by dropping the line with hook and
sinker.

2

Power lever

- You can freely adjust winding power, or winding speed, from zero(ON/OFF) to maximum, by 32 steps, by using
the lever.

- Tilting the lever forward adds power and speeds up the winding.

- Pulling the lever back slows down the winding.

- Without the lever positioned to OFF, it is impossible to start winding. You have to pull it back to the OFF position
before you start winding. An audible sound indicates the OFF position.

- The power lever is used to set numerical values on the various function displays.

3

Waterproof drag

- Adjusting the star drag allows the spool to slip against a strong pull to avoid line breakage.

(1) Adjust the drag while reel is on the rod and the line is strung through all the line guides.
(2) Adjust drag with the clutch ON, while pulling the line with your hands. Normally, the drag is adjusted to prevent

the weakest line in the line system from breaking.

4

Clutch

- Turning the handle automatically engages the clutch.

- ON position > line winding can be done.

- OFF position > spool is free-turning to let out line.

Levelwind

5

- The levelwind distributes line evenly on the spool as you wind it in.

(Under some special circumstances line may not wind evenly because of the clearance between the levelwind

and the line.)

Enclosed items

6

- Power cord

- Levelwind threader (This tool simplifies threading line through the levelwind.)

- Rod Clamp

9

Line data input (When line length is known)

This method is used when the line length is known before winding. In the example below,
PE 6 – 1000m is wound.

1. Run line through the levelwind guide and tie it onto the spool.

The levelwind threader makes this process easier. Make sure to
tie the line onto the pin found on the spool to avoid the line
slipping.

2. Move the power lever to the OFF position.

3. Press the MODE SETTING BUTTON and hold for five

seconds, until the display shows 0.0. When the button is
released, the display will then change to the figure on the right,
which shows P1.

1

Levelwind Guide

Main line

Power lever

2

Pin

3

Make sure the drag is set firmly.

Tension indicatar

4. Push the power lever forward to maximum and wind the line to

its end.

As the power lever is moved forward, the

tension indicator. Keep line tension between level 5 and 7 while
winding on line.

1.Do not allow line to rub against the palming plate while winding as it could scratch the plate.

2.The motor can be overloaded when winding at very high tension for a long time (about 15

minutes). In this case, the motor will automatically stop. This does not occur while fishing

Attention

as water helps cool down the motor. If the motor stops, wind manually or move the
power lever momentarily back to OFF and then resume winding. Wind the line at high
speed (less tension).

P1 display changes to a

4

MAX

10

Line data input (When line length is known)

5. Pull the lever back to the OFF position, after winding.

1.Do not wind the end of the line onto the spool because it causes incorrect length

calculation. Move the power lever to OFF, and wind manually when nearing the end of
the line.

Attention

5

OFF

Do not reel in the end of the line

6. Press RESET BUTTON for 2 seconds, until the display shows

800. (800 is the default setting)

7. Enter the line length with the power lever. (in the figure on the

right, line length is 1000 m).

8. Press RESET BUTTON for 2 seconds and a beep will be

heard. The display should return to
procedure.

Err” appears on the display, you must use the MODE SET

If “

BUTTON

to re-enter the data.

0.0, completing the setting

6

7

MAX

OFF

8

11

Line data input (With backing line)

This method requires use of Daiwa braided line that is color coded to show length and has a total
length greater than 100 m.

1. Run the backing line through the levelwind guide and tie it onto

the spool. The levelwind threader makes this process easier.
Make sure to tie the line onto the pin found on the spool to
avoid the line slipping.

2. Wind the backing line.

If the power lever is not already at OFF position, then pull it
back to OFF position before beginning to wind.

3. Tie the backing line securely to the main line.

1

Levelwind Guide

Main line

Power lever

2

Pin

3

Backing line

OFF

Main line

Tie

4. Press the MODE BUTTON for 5 seconds, when the display will

show 0.0.

P1 will be blinking.

5. Press the MODE BUTTON twice and change the display to

backing line input.

P2 will then be blinking.

4

5

12

Line data input (With backing line)

6. As indicated by the lineʼs color coding, wind the line up until the

remaining line is 100m.
With the power lever moved forward, P2 changes into a tension
indicator. Keep line tension between 5 and 7 while winding.

1.Do not allow line to rub against the palming plate while winding as it could scratch the plate.

2.The motor can be overloaded when winding at very high tension for a long time (about 15

minutes). In this case, the motor will automatically stop. This does not occur while fishing

Attention

as water helps cool down the motor. If the motor stops, wind manually or move the
power lever momentarily back to OFF and then resume winding. Wind the line at high
speed (less tension).

7. Press RESET BUTTON for 2 seconds.

P2 blinks and the counter in the lower area shows 50. The

upper counter digits increase as line is wound.

8. Wind on another 50 m of line, keeping line tension at the

suggested level.

6

MAX

7

9. Press RESET BUTTON for 2 seconds.

The lower counter shows 100.

10. Wind the remaining 50m, keeping line tension at the

suggested level. Do not wind line all the way onto the spool.

11. Press RESET BUTTON for 2 seconds and 0.0 will appear.

This is the end of the procedure.

1.Do not wind the end of the line onto the spool because it causes incorrect length

calculation. Move the power lever to OFF, and wind manually when nearing the end of
the line.

Attention

9

11

Should “Err” appear on the display, then use the MODE SET

BUTTON to re-enter the data.

13

Line data input (Backing line 2)

This procedure is to enter the line length after it has been wound onto the reel. It is necessary that
you know the line length and that it is greater than 100m.

1. Connect the battery to the reel.

2. Press the MODE SET BUTTON for 5 seconds, changing the

mode to P1.

2

3. Press the MODE SET BUTTON 2 more times and set the

mode to backing line 2.

 This mode shows P3 blinking on the low left of the display.

4. Paying attention to the line’s color coding, pull 50m of line off of

the spool.

5. Press the RESET BUTTON for 2 seconds.

 This will show the digits 100 in the lower area of the counter.

14

3

5

Line data input (Backing line 2)

6. Pull an additional 50m of line from the spool.

7. Press the RESET BUTTON for 2 seconds to show 100.0 on

the upper counter.

8. Wind up the 100m of line you pulled from the reel. This

completes the procedure.

1.Do not wind the end of the line onto the spool because it causes incorrect length

calculation. Move the power lever to OFF, and wind manually when nearing the end of
the line.

Attention

Should “Err” appear on the display, then use the MODE SET

BUTTON to re-enter the data.

2.There are cases in which the length of the line will not be displayed if it exceeds 100m
when entered with this method.

7

15

Functional setting operation

(1. Mode setting display)

How to set the many functions available

1.There are many useful functions in the mode

2.Use the power lever to change numerical values on the setting displays for each function. Complete
your adjustments and lock in the values by pressing the MODE BUTTON.

1. Press the MODE BUTTON to choose a display.

 Each press of the MODE BUTTON changes the display to the

next function.

 Holding the MODE BUTTON down, rapidly scrolls through the

displays, quickly getting you back to the depth display.

 At each mode setting display, the default setting can be

retained by pressing the RESET BUTTON.

 While letting out or winding line, the MODE BUTTON cannot be

used to change settings.

Power lever

Jig/pickup pattern Jigging pattern Jigging length

MODE
BUTTON

1

MODE
BUTTON

MODE
BUTTON

Pickup speed Jig waiting time Jigging range Winding speed display

MODE
BUTTON

(Each display example is the default setting)

MODE
BUTTON

16

Functional setting operation

(1. Mode setting display)

2. Use the power lever to set numerical values.

 At its MAX position, numbers count upward rapidly. At the OFF

position, numbers count downward rapidly.

 Around mid position, numbers change at a slower pace.

3. Press MODE BUTTON to complete the setting.

 Pressing the mode button locks in the values you have set and

moves on to the next display.

 Depress and hold the MODE BUTTON to rapidly scroll back to

the depth counter screen.

 Pressing the RESET BUTTON at a setting display returns

numbers to their default values (This resetting does not apply to
the fishing record display.)

2

Power lever

MAX

OFF

OFF

MAX

3

MODE
BUTTON

MODE
BUTTON

Line feeding

Total winding distance (km)

Total hours of fishing (H)

Display revision indicator

MODE
BUTTON

Chumming timer Fishing

record

Press RESET BUTTON and

MODE BUTTON simultaneously

for 2 seconds.

17

MODE
BUTTON

Depth counter

Depth counterRevision

Functional setting operation

Surface depth setting

Before you begin fishing, make sure the counter is set to zero at the waterʼs surface.
This is extremely important to ensure accurate fishing depth readings.

1. Connect the reel to the battery, put the line through all the

guides, and prepare your terminal rig.

(2. Before you begin fishing)

2. Place the rod into the rod holder in the position it will normally

rest while fishing.

3. Lower the terminal rig to the waterʼs surface and press the

RESET BUTTON. (water surface zero setting)

The display resets to 0.0 and blinks.

2

3

1.When new line is wound up, or when line has been pulled under heavy tension, line

stretch may cause a gap in the depth reading at the surface. Simply reset the surface
setting with the reset button.

Attention

When the main line is cut or broken off.....

- Should your line break, revise data as follows.

- Wind the line to the rod tip, and press the RESET BUTTON for 3
seconds. (At depths greater than 10 m, 3-second-pressing is
employe
shows 0.0 then your re-adjustment is complete and data has
been revised.

- Unless you reset the data on the reel, it will not be able to count
accurately.

d accidental pressing of the button.) If the display

18

Functional setting operation

(3. Auto stop function)

Auto stop setting

The Auto stop depth may be set to meet your own specific needs.

- Auto stop adjusts to operate at depths from 1 m to 5 m (in 10 cm increments).

- It prevents accidentally winding swivels, terminal rigs etc. into the rod tip and stops your rig at a consistent depth

for convenient checking and changing of baits and sinkers.

- Line stretch can cause an inaccurate reading at the surface. Simply reset the counter to zero at the surface.

1. Connect the reel to the battery, and press the RESET BUTTON

with your terminal rig at the surface.

The display shows 0.0.

2. Raise the rod and adjust the line length from the rod tip so you

can reach the rig easily. In the figure, its length is 1.5 m.

Checking and changing sinkers, baits etc.

Use

3. After adjusting length, press the INVERSE COUNTER

BUTTON for 2 seconds.

When blinks, this procedure is completed.
Default setting is 2.0 m. (Without pressing the RESET BUTTON

the winding stops at a depth of 5.0 m.

The lamp will blink when the setup has been completed.

1

2

1.5 m

3

4. When checking or changing a bait, simply wait until the reel

automatically stops winding and raise the rod tip.

Auto stop

Auto stop automatically brings your terminal rig to the surface, stopping consistently at your
pre-set depth preference. It eliminates the need to constantly monitor depth as it comes up.

- The auto stop function assists when winding with the power lever, jigging, or winding with the chumming timer.

- After the rig is ready, reset the depth counter to zero by pressing the RESET BUTTON.

(water surface zero setting) (After this, appears on the display)

- Without pressing the RESET BUTTON, winding stops at a depth of 5 m.

- If you have pressed the RESET BUTTON, the alarm sounds at 2m increments above the depth of 8 m, and

winding stops at 2 m.

-

When auto stop depth is set, the alarm sounds every 2 m above the depth of 6 m, and winding stops at the set depth.

- After auto stop stops winding, the power lever can be used up to 0.0 m. However, above 0.0 m, motor winding

such as, power lever and PICKUP, cannot be employed until the RESET BUTTON is pressed.

- Depending upon the rocking of the boat or sinker weight, auto stop depth can overrun slightly

happen, increase the depth of the auto stop.

. Should this

19

Functional setting operation

Line feeding function

The line feeding function lets our line with the motor assisting the spool.

- The line feeding mechanism begins to work at a depth of 2.5 m

below the pre-set auto stop depth.

- If the clutch becomes ON while the reel is furnishing line, the

spool begins to rotate to avoid line slack.

- Speed of the line going out is adjusted with 32 speed levels

ranging between 0 and Hi. It is adjusted in the line feeding
mode.

1. Press the MODE BUTTON to show the line feeding speed

adjustment display. Default setting is zero (OFF).

 Set the speed level with the power lever.

2. Press the MODE BUTTON three times to show 0.0 (depth

counter) to complete.

 The will blinks.

(4. Line feeding function)

(adjustment of
line furnishing)

OFF

While the reel is feeding line with this function, its speed cannot

be changed.

(the figure corresponds
to the case of setting to 5)

20

Functional setting operation

Pickup speed preference

(5. Pickup speed setting)

1. Press MODE BUTTON.

If the display is at display, then move the power lever or

press RESET BUTTON to show the display shown on the right.

2. Press MODE BUTTON again.

This display is the pickup setting display.

3. Set speed with the power lever.

1

2

3

While the power lever is at MAX position,
pressing the
motor run at the pre-set pickup speed.

PICKUP BUTTON makes the

Use

4. Press the MODE BUTTON to go back to depth readout.

1.While the PICKUP BUTTON is in use for winding, winding speed is not displayed.

Attention

(the figure corresponds
to the case of setting to 5)

4

21

Functional setting operation

Inverse counter

Two counters are better than one. This reel has counters from both the surface and from the bottom.

The default inverse counter setting is OFF. To turn it ON, see page 26.
In the following example, intended fishing range is 94 m, which is 6 m from the bottom.

(6. Inverse counter)

1. Clutch OFF to send the rig to the bottom

OFF

2. At the bottom, move the clutch to ON by turning the reel handle

or flipping the clutch lever.

ON

1

3. After winding up any slack line, press the INVERSE COUNTER

BUTTON

By pressing the INVERSE COUNTER BUTTON, the lower area

counter is reset. Wind line until the intended depth is reached.

and wind up 6 m.

By pressing the INVERSE COUNTER

BUTTON,

accurate record of fishing time.

the timer starts and keeps an

Use

22

3

Functional setting operation

Jigging

Jigging is an extremely valuable function.
After setting your preferences, pressing the JIG/PICKUP BUTTON starts the function.
Speed of the jigging can be adjusted with the power lever.

(7. Jigging)

1. Press the MODE BUTTON to show pickup / jigging display.

(When jigging is chosen, the pickup function cannot be used.)

2. Jigging pattern is selected with the power lever.

There are four patterns; 123 (master), 1 step, 2 steps, 3 steps.

Jigging setting displays appear in the following order;
Pattern (step) > length (m) > waiting time (sec) > range (m)

3. Press MODE BUTTON to show the next display. Pressing it

also locks in the previous setting.

1

Jig/pickup

2

3

4. In the same manner, set length, waiting time and range.

By pressing the JIG/PICKUP BUTTON during the jigging setting

display, the display will show depth and begins jigging.

Pressing and holding the MODE BUTTON will quickly scroll you

back to the depth counter display.

5. After pressing the JIG/PICKUP BUTTON, use the power lever

to start jigging.

Jigging speed is controlled with the power lever.
As the jerking starts, indicator blinks.
Pressing the JIG/PICKUP BUTTON again stops jigging.

23

Interval time

5

Jigging distance

Jigging range

Functional setting operation

Jigging master

You can choose the jigging pattern, range, waiting time and length you require.

- Pressing the JIG/PICKUP BUTTON, starts jigging, with the display showing the indicator. (Pressing the

button once more cease jigging.) The power lever controls jigging speed.

- Shifting of jigging speed is done easily with the lever control.

- When a fish strikes during jigging, it turns off providing the power lever is turned to the OFF position. After that,

normal winding is done with the power lever.

- To show the jigging display, refer to page 16.

1. Jigging pattern

You can choose the number of steps you wish for your jigging

pattern.

(7. Jigging)

(Preference setting)

One-step jigging Two-step jigging Three-step jiggingMaster jigging

A

Master jigging (123) is the method in which the number of jigging

steps is selected automatically by the computer.

2. Jigging length

A

B

A

B

B

A : 4 seconds stop
B : 0.4 seconds stop

You can choose the length of the line wound up in one jig action.

(Depending upon the sinker, speed of winding, the jigging
length may overrun its setting slightly.)

The length can be set in increments of 50 cm between 0.5 and

10 m.

24

(Preference setting)

Functional setting operation

(7. Jigging)

3. Waiting time

You can choose the waiting time between jigs. The interval time

is set in seconds.

Example)

Three-step jigging
5 seconds interval time

Three-step jigging

Interval time
(5sec)

- If jigging time is longer than the chumming timer setting, then the chumming timer
setting takes priority and will wind up the line.

Three-step jigging

Interval time
(5sec)

Attention

4. Jigging range

The depth range for jigging is set in 1 m increments. If the range

is set to zero, then jigging continues right up to the auto stop
depth.

(Preference setting)

(Shown is the interval
time set to 5 sec)

Example)

Range is 20 m.

Interval time
(5sec)

(Preference setting)

Interval time
(5sec)

Jigging range
20 m

(Shown is the jigging
range set to 20m)

25

Functional setting operation

Winding speed display

In the default setting, the lower area counter displays the winding speed.

The chumming timer display area shows the remaining time until
the auto stop is reached. (p. 27)
The inverse counter numbers can be changed to indicate winding
speed.
Rate of speed indicated is meters per minute (m/min).

(8. Winding speed indicator)

Example)
100 m/min

1. Press MODE BUTTON to show speed indicator display.  

     is shown on the screen.

In the default setting, the inverse counter is OFF.

2. Turn it ON with the power lever.

3. Press the MODE BUTTON to display the next setting display.

1

2

3

4. Press the MODE BUTTON three times to show the water depth

on the display. The depth counter will then start to function.

26

4

Functional setting operation

Displaying of the remaining time to auto stop

Two counters are better than one. This reel has counters from both the surface and from the bottom.

When the display is set to indicate the actual speed, the
chumming timer display portion indicates the remaining time
before it reaches the auto stop position. However, the display will
go out about five seconds before reaching the auto stop position.

This function works if the remaining time is within 7 minutes. If the
remaining time is more than 7 minutes, then the partial circle icon
blinks.

(display example)

- Digits show seconds.

- Each partial circle stands for one minute.

(9. Remaining time to auto stop)

Example)

To wind up from 50 m depth to the
auto stop depth, it takes 29 seconds
at the speed of 80 m / min.

Remaining time; 2 min 30 sec

Remaining time; 5 min 30 sec

- If you would not like the display to show the remaining time
before reaching the auto stop position at ship side, please set
the depth counter mode ON.(see page 26)

- You cannot put out only the remaining time before reaching the
auto stop position.

27

Functional setting operation

Chumming timer winding

The right timing for the best results. After a pre-determined amount of time has passed, the reel
starts winding automatically.

- After pre-set 5 minutes have passed, the reel automatically

winds up.

- When the timer is set, the timer indicator is shown in the

display. To stop using the timer, set its time to zero.

- Pre-set time can be confirmed by pressing the INVERSE

COUNTER BUTTON.

- Winding of the chumming timer functions when the depth

counter indicates between +20m and -20m. It will not function
any more if once the indication of the depth counter goes out of
this range.

(10. Chumming timer winding)

(In the case when the timer winding is
set to 5 minutes)

1. Press MODE BUTTON until you come to the timer setting

display.

    is on the screen. The default setting is zero minutes or  

  .

The chumming timer helps ensure you check
baits at even intervals, a real help when
dropping multiple lines.

Use

2. Use the power lever to set the number of minutes.

(Shown is the timer set to 3 minutes.)

1

(timer setting display)

2

28

Functional setting operation

(10. Chumming timer winding)

3. Press MODE BUTTON twice.

- When the display goes back to depth counter, then the

procedure is completed.

- The indicator is seen on the display.

- The time set can be checked by pressing the INVERSE

COUNTER BUTTON.

- Pressing and holding down the MODE BUTTON scrolls quickly

back to the depth display.

4. When the set time is reached, the reel begins to wind at its

maximum speed.

An audible alarm sounds.

Chumming timer

3

This function provides a useful timer.

- This function displays the time passed after the presentation of
your bait or lure. It can be used for chumming, jigging timing or
reeling in your rig.

- The chumming timer starts from 7.0 m on the counter, unless a
specific fishing range has been entered into memory.
Display time is shown in seconds if remaining time is less than 60
seconds, in minutes if remaining time is more than a minute.

The outer frame expresses 10
seconds with each arch segment.

1. Pressing the INVERSE COUNTER BUTTON while the timer is in operation re-starts the
rom 0.0 .

timer f

Counter initially shows seconds, after 1minute,
indicates minutes.

Attention

29

Functional setting operation

Display revision

You can recalibrate the counter should it not indicate an accurate depth compared to depth markings
on your line.

Example below is the case in which, though the counter shows

103 m, color markings on the line indicate 100 m.

(11. Display recalibration)

1. Press MODE BUTTON six times to show on the display real

fishing time and total winding length.

2. Press MODE BUTTON and RESET BUTTON at the same time

for 2 seconds.

This displays revision display.

3. Move the power lever to change the display’s reading to 100.0.

(Occasionally, for the revision rate, the exact number cannot be

attained.)

1

2

3

OFF

4. After 100.0 is reached, then press the MODE BUTTON to

return to depth display.

With this procedure, the inverse counter is reset. In the revised

display, pressing of the RESET BUTTON
back to the unrevised value.

changes the reading

30

MAX

4

How to fix the Rod Clamp

When you use a metallic bat or for your fishing of a big charge, you should always utilize the Rod
Clamp.
(sing the Rod Clamp, it is possible to cramp rods with diameter up to 25-34mm)

1. Insert the Bolt in the clamp setting hole, and fix it by tightening

the Nut and the Washer.

2. Hold the rod in position while attaching the clamp.

Tighten the rod clamp nuts to secure.

To fix the reel with a rod clamp apply the screws to the reel foot

then place the rod between the threads then add the clamp and
tighten the nuts.

1

Bolt

Nut

Washer

Wrench

2

rod

Tighten

Rod Clamp

Attention

Nut

Collar

*Use the collar only on a rod 25 mm or

less in diameter.

- If the Nut is tightened too firmly, there is a danger of deforming the rod depending upon
rod material, especially with composite rods and reel seats.

31

Useful functions

Various alarms

Many kinds of information are indicated by audible alarms.

Power lever alarm

- Placing the Power lever at MAX or OFF positions evokes an alarm.

Auto stop alarm

- While winding up, starting 6 m below the auto stop depth, an alarm beeps at two meter intervals. Upon reaching
the auto stop depth, a long alarm sounds.

Range memory alert

- While lowering your rig back into the strike zone, starting 6 m above the memorized strike depth, an alarm
sounds at two m intervals with a long alarm sounding once the target depth is reached.

(This range memory alarm does not sound unless line has been wound more than 6 m above the memorized

depth.)

Switch alarm

- Each time a button is pressed, a confirming beep is sounded.

Excessive voltage alarm

- Should you attach a power source with a voltage higher than the acceptable level, a continuous alarm will
sound. DO NOT operate the reel. Disconnect the power source. Connect a power source with the proper
voltage.

Timer alarm

- Chumming timer winding is indicated by an alarm.

Display light

Backlighting of the display provides easy reading for early morning or night fishing.

Backlighting of the display provides easy reading for early morning

or night fishing.

- As long as the reel is connected to a power source, the display
backlight is on.

Breaker display

- For safety, an excessively heavy load on the reel will activate the
circuit breaker system and stop automatic winding. While this
system is working, the display appears as shown on the right.

32

Reel Specifications

Reel Specification list

Product name
Product code

Gear ratio(manual winding)
Weight (g/oz)
Max Drag power (kg/lb)
Line Capacity (m)

Number of Ball bearings
Power-supply voltage

Electric current (Amps)

Speed shifting

No load
stall
Max
No load

TANACOM 1000

40801001

1500 g / 53 oz

22kg/48lb

DAIWA BRAIDED BRAIDEDMONO

PE6(80lb)-1000m(1100yds)

PE8(100lb)-800m(880yds)

PE10(120lb)-600m(660yds)

PE12(150lb)-500m(550yds)

30lb-700m(770yds)

40lb-500m(550yds)

DC 12 V – 16.8 V

0 – 140 m / min (continuous shifting)

2.3 : 1

4

3A
10A
30A

60lb-1000m(

80lb-800m(880yds)

100lb-600m(660yds)

120lb-500m(550yds)

1100yds)

Counter display

Depth display range

Usable temp. range

Specifications may be changed without prior notice for the purpose of improvement.

Upper counter; 0.0 – 999.9 m
Lower counter : -99.9 – 999.9 m

-10 to +60 (degrees centigrade)

33

Parts List

TANACOM 1000

TANACOM 1000

No, Parts NameParts No, No, Parts NameParts No, No, Parts NameParts No,

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45

6H3778031
6E0965040
6H4398011
6H4399010
6F5719020
635177060
6E0332010
6E4896222
632059010
6G2251030
6F6738021
6G2252010
6G0703010
6G0702010
635382070
663721020
663756010
6B4117000
6G8115043
6G8117010
637169060
6F7137010
6G1264021
632059010
6F7746000
6G8118010
6G1568010
6F5941041
6F2069010
6F7137010
6G2257010
632016111
6F6826000
6F3891020
6G3825026
6G4888010
6G8119010
6G3859010
6F7012010
6G3626010
6F0783010
6B2705011
6F5953010
635161010
6G1734010

SIDE PLATE(L) AS
WASHER
COLLAR
GEAR
WASHER
SCREW
LEAF SPRING
SCREW
RETAINER
WASHER
WASHER
GEAR
BALL BEARING
RING
SCREW
BALL BEARING
BEARING
WASHER
SPOOL AS
MAIN SHAFT
WASHER
BEARING
GEAR
RETAINER
WASHER
METAL AS
BALL BEARING
PLATE
SCREW
BEARING
GEAR
RETAINER
WASHER
BALL BEARING
FRAME AS
O-RING
MOTOR AS
SCREW
WASHER
MOTOR HOLDER AS
BEARING
RING
O-RING
TRUSS SCREW
PACKING

46
47
48
49
50
51
52
53

*1 54

55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90

6G1413025
6F7148010
6F7396012
6F5958010
6F5959010
6F7397010
6G2257010
632016111
6G8121022
612206011
6F7746000
6E3541011
6G8354011
6G3628011
6F4672012
6B4117060
632059010
6G3629010
6B8641010
6E2525010
6F7153021
6F6578010
637558010
632076010
6G3745061
6G3630010
6G3631010
6F5970010
6E2906010
6F7402012
6G4734010
6F7730010
6F6083013
6F5972010
6F5973013
637466040
6G8120010
6B3602120
637238333
6B3603020
6F8170010
6F6578010
6G8290010
6F7156010
6G3748054

*1: Part No. 6G8121012 is applied to the U.S. model.
*2: Part No. 116 is only applied to the European Model.
There may sometimes be a difference between the purchased reel and the Dismantled Parts Chart or the parts list above due to the

adjustment process etc. We appreciate your understanding.

METAL AS
O-RING
PLATE
O-RING
RING
BEARING
GEAR
RETAINER
LEVELWIND AS
PIN
WASHER
NUT
WORM SHAFT AS
PIPE
COLLAR
WASHER
RETAINER
PILLAR
RETAINER
BUSH
GEAR SHAFT
O-RING
WASHER
RETAINER
MOTOR COVER
SCREW
SCREW
SLIDE PLATE
CLUCH PLATE
PINION
SPRING
PIN
SPRING
STOPPER
RATCHET AS
WASHER
DRIVE GEAR
WASHER
WASHER
WASHER
PACKING
O-RING
COLLAR
BEARING
FINGER COVER

91
92
93
94
95
96
97
98

99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115

*2 116

6H9928010
6F4690061
6F5979011
6F5982012
616080010
635382120
6E2860010
635387050
6G4059010
6F2859010
6F3031020
6F4297024
634240041
6F4300052
6E2535010
6F4700021
6B7477021
6F4701011
6F5504151
6H6365010
6H9918010
6B8621022
6F4712053
6F6610023
6G8687012
6G9054010

SIDE PLATE(R) AS
LEVER
PLATE AS
SPRING
SPRING WASHER
SCREW
LINE STOPPER
SCREW
SCREW
SPRING WASHER
NUT
LEVER AS
NUT
CAP
SPRING WASHER
CAP
LEAF SPRING
WASHER
STAR DRAG
COLLAR
HANDLE AS
NUT
CAP
CAP
CORD
FERRITE CORE

34

Trouble shooting

Symptom Possible causes To do

It is a normal function to avoid over

The counter displays 0.0 m.

winding. Press RESE
continue winding.

Motor does not
respond to the
power lever.

Counter display
does not appea

r.

Inverse counter

Did not pull the lever to OFF
position.

Unstable power source.

Battery charge is low.

Cord worn or corroded.

Incorrect battery connection.

Did not press

JIG/PICKUP BUTTON.

Pull the lever to OFF and then move
forward again to start winding.

Use another power source, such as
electric reel specific batteries.

Recharge the battery.

Replace the cord.

Connect correctly.

It is normal. Press

INVERSE COUNTER BUT

does not appear.

Jigging function

Inverse counter is OFF.
(default setting)

Power lever is at OFF.

Using MODE BUT
setting of this function.

Push the lever forward.

does not
respond.

Pickup mode is selected.

With MODE BUT
jigging mode.

TON, select the

T BUTTON to

.

TON

TON, change the

Ref.
page

19,20

9

2

3

5

2

22

26

23

23-25

The reel jigs on
its own.

Auto stop
function does
not work.

There are
counter errors.

Pickup does not
respond.

Low power voltage.

Did not press
at surface.

Error for sinker weight or
rocking of the boat.

Line is elongated.

Line length has increased
due to stretching.

Speed setting is at zero.

RESET BUTTON

Replace with a recharged batter

Press RESE
to zero with rig at the surface.

Adjust settings of auto stop function.

Reset the depth counter at the surface.

- Reset the counte

- Revise the displa

- Re-enter line data.

Press MODE BUT
speed setting.

T BUTTON to reset depth

r.

y.

TON to select winding

y.

3

18

19,20

18

18

30

10-15

21

Contact your dealer if the reel does not function properly despite the above details being con­firmed, in the event of other problems arising, and to order parts.

35

Reference/Référence/Hinweis
Instrucciones/Riferimenti

COMPANY
NAME

ADDRESS

TEL NO.

Web Address

COMPANY
NAME

ADDRESS

TEL NO.

Web Address

COMPANY
NAME

DAIWA SPORTS LIMITED

Netherton Industrial Estate,
Wishaw ML2 0EY,
Lanarkshire,Scotland, U.K.

01698-355-723

http://www.daiwasports.co.uk/

COMPANY
NAME

ADDRESS

TEL NO.

Web Address

DAIWA FRANCE S.A.S

25 BOULEVARD INDUSTRIEL
BP 30208
76304 SOTTEVILLE LES
ROUEN CEDEX. FRANCE

02-32-91-96-50

http://www.daiwa-france.fr/



DAIWA CORMORAN SPORTARTIKEL-VERTRIEB GmbH

Industriestrasse 28
82194 Groebenzell
GERMANY

08142-5005-0

http://www.daiwa-cormoran.info/

Daiwa Corporation Daiwa Australia Pty. Ltd

COMPANY
NAME

ADDRESS

TEL NO.

Web Address

11137 Warland Drive
Cypress, CA 90630

[phone]

http://www.daiwa.com/

ADDRESS

TEL NO.

Web Address

Unit K, 134 – 140 Old Pittwater
Rd,
Brookvale NSW 2100

[phone]

http://daiwafishing.com.au/



LIMITED WARRANTY TERMS

WARRANTY WILL EXPIRE WHEN ONE OF THE FOLLOWING HAS BEEN SURPASSED.
*ONE YEAR FROM DATE OF ORIGINAL PURCHASE.
*200 TOTAL HOURS OF USE.

GARANTIE

LA GARANTIE EXPIRE LORSQUE L’ON ATTEINT
*SOIT 1 AN APRES L’ACHAT
*SOIT 200 H D’UTILISATION

TERMINOS DE GARANTÍA LIMITADOS

La garantía caducará cuando algo de lo siguiente se haya sido superado.
*Un año de la fecha de la compra original
*200 horas totales de uso