Daikin BRC7F530W, BRC7F530S, BRC7EB530W Installation manuals

INSTALLATION MANUAL

Wireless remote controller kit

BRC7F530W BRC7F530S BRC7EB530W

MODE

TIMER

RESERVE

CANCEL

DOWN

/TEST

SWING

FAN

TIME

TEMP

ON OFF

SETTING

MODE

TIMER

RESERVE

CANCEL

DOWN

/TEST

SWING

FAN

TIME

TEMP

ON OFF

SETTING

1,6

BRC7F530W BRC7F530S BRC7EB530W

1X 1X

1X 1X 1X

2X 2X 2X

1X 1X 1X

2X 2X 2X

3X 3X 4X

4X 4X 4X

1X 1X 1X

1 1 2 3 4 5 6 7

8 9 10 11 12

X24

X1A X2A

5342

BRC7F530W BRC7F530S BRC7EB530W

Wireless remote controller kit

Installation manual

Contents Page

Safety considerations .....................................................1

Before installation ...........................................................1

Accessories ................................................................... 1

Note to the installer ....................................................... 1

Remote controller installation ......................................... 2

Installing the wireless remote controller ........................2

Determination of address and MAIN/SUB remote

controller........................................................................ 2

Setting procedure .......................................................... 2

Installation of the transmitter board ............................... 3

Installation of the decoration panel................................ 3

Installation of the receiver in case of BRC7EB530W ....4

Installation of the receiver in case of BRC7F530S/W ... 4

Field setting ....................................................................5

Test operation.................................................................6

READ THIS MANUAL ATTENTIVELY BEFORE STARTING UP THE UNIT. DO NOT THROW IT AWAY. KEEP IT IN YOUR FILES FOR FUTURE REFERENCE.

IMPROPER INSTALLATION OR ATTACHMENT OF EQUIPMENT OR ACCESSORIES COULD RESULT IN ELECTRIC SHOCK, SHORTCIRCUIT, LEAKS, FIRE OR OTHER DAMAGE TO THE EQUIPMENT. BE SURE ONLY TO USE ACCESSORIES MADE BY DAIKIN WHICH ARE SPECIFICALLY DESIGNED FOR USE WITH THE EQUIPMENT AND HAVE THEM INSTALLED BY A PROFESSIONAL.

IF UNSURE OF INSTALLATION PROCEDURES OR USE, ALWAYS CONTACT YOUR DAIKIN DEALER FOR ADVICE AND INFORMATION.

The English text is the original instruction. Other languages are translations of the original instructions.

Safety considerations

Please read this "Safety considerations" carefully before installing air conditioning equipment and be sure to install it correctly. After completing the installation, make sure at start up operation that the unit operates properly. Please instruct the customer how to operate the unit and how to perform maintenance.

Meaning of caution symbols

Failure to observe these instructions properly may result in property damage or personal injury.

Information classified as NOTE contains instructions to ensure proper use of the equipment.



Refer also to the installation manual supplied with the indoor unit and the installation manual supplied with the decoration panel.



There is only 1 possible installation position of this kit into the decoration panel. It is therefore recommended that installation orientation of the decoration panel is confirmed prior to installation of this kit.

• Ensure that nothing interrupts operation of the wireless remote controller.

• Ensure that the signal from the remote controller can easily be transmitted.

• Ensure that the operation display lamp and other indicator lamps can easily be seen.

• Ensure that there is neither a source of light nor a fluorescent lamp near the receiver.

• Ensure that the receiver is not exposed to direct sunlight.

Before installation

Accessories

See figure 1. Check if the following accessories are included with your kit.

1 Receiver 2 Transmitter board 3 Wireless remote controller 4 Remote controller holder 5 Alkaline battery of type AAA.LR03 6 Unit number label 7 Screw for installing remote controller holder 8 Installation manual

Operation manual

9 Clamp 10 Plastic pin 11 Plastic holder 12 Sealing

Note to the installer

Be sure to instruct the customer how to properly operate the system showing him/her the supplied operation manual.

Wireless remote controller kit 4P343087-1B – 2013.05

Installation manual

Remote controller installation

(1)

(2)

1 2 3

Installing the wireless remote controller



Do not throw the remote controller or subject it to powerful shocks and do not store the remote controller where it may be exposed to moisture or direct sunlight.



When operating, point the transmitting part of the remote controller in the direction of the receiver.



The direct transmitting distance of the remote controller is approximately 7 meters.



The signal cannot be transmitted if something such as curtains blocks the receiver and the remote controller.

Installing to a wall or a pillar

1 Fix the remote controller holder

with the supplied screws.

2 Slide the remote controller into the

remote controller holder from the top.

How to insert the batteries

1 Open the back cover of

the remote controller by sliding it in the direction of the arrow.

2 Insert the attached dry

cell batteries. Properly insert batteries by matching the (+) and (–) polarity marks as indicated. Then close the cover as before.

Determination of address and MAIN/SUB remote controller



If setting multiple wireless remote controllers to operate in one room, perform address setting for the receiver and the wireless remote controller.



If setting multiple wired remote controllers in one room, change the MAIN/SUB switch of the receiver.

Setting procedure

Setting the receiver

Set the wireless address switch (SS2) on the transmitter board according to the table below.

Unit No.

1 2 3

Wireless address switch (SS2)

When using both a wired and a wireless remote controller for 1 indoor unit, the wired controller should be set to MAIN. Therefore, set the MAIN/SUB switch (SS1) of the transmitter board to SUB.

MAIN SUB

MAIN/SUB switch (SS1)

Setting the address of the wireless remote controller

(See figure 3)

A Field Set mode B Address (is factory set to " C Display setting

Setting from the remote controller

1 Hold down the button and the button for

at least 4 seconds to enter the Field Set mode. (Indicated in the display area in the figure.)

2 Press the button and select an appropriate

display setting ( the display switches between "

"Display setting a/b" on page 3 for full comprehension

of this feature.

3 Press the button and button to set the address.

Address can be set from 1 to 6, but set it to 1~3 and to same address as the receiver. (The receiver does not work with address 4~6.)

4 Press the button to confirm the setting.

5 Hold down the button for at least 1 second

to quit the Field Set mode and to return to normal display again.

a/b). Each time the button is pressed

1")

a" and "b". Refer to

Installation manual

Wireless remote controller kit

4P343087-1B – 2013.05

+ 8 hidden pages