Dahua SD6AL2-HNI Operation Manual
Dahua Network Speed Dome Web 3.0 Operation Manual
Dahua Network Speed Dome Web3.0 Operation Manual
Version 1.0.0
Dahua Technology CO., LTD
Dahua Network Speed Dome Web 3.0 Operation Manual
i
Table of Contents
1 Network Connection ................................................................................................................... 1
1.1 Preparation ..................................................................................................................... 1
1.2 Log in .............................................................................................................................. 1
1.3 Live Interface ................................................................................................................. 3
1.4 Encode Setup ................................................................................................................ 3
1.5 Video Window Setup .................................................................................................... 4
1.6 System Menu ................................................................................................................. 5
1.7 Video Window Function Option .................................................................................. 6
1.8 PTZ Control .................................................................................................................... 7
1.9 Joystick ........................................................................................................................... 8
1.10 PTZ Setup/Menu ........................................................................................................... 8
2 Playback ..................................................................................................................................... 11
2.1 Video Playback ............................................................................................................ 11
2.1.1 Play Function ........................................................................................................ 12
2.1.2 Playback File ........................................................................................................ 12
2.1.3 Playback Cut ......................................................................................................... 15
2.1.4 Record Type ......................................................................................................... 16
2.1.5 Progress Bar Time Format ................................................................................. 16
2.1.6 Aux Function ......................................................................................................... 16
2.2 Picture Playback ......................................................................................................... 17
2.2.1 Play Function ........................................................................................................ 17
2.2.2 Playback File ........................................................................................................ 18
Dahua Network Speed Dome Web 3.0 Operation Manual
ii
2.2.3 Snapshot Type ..................................................................................................... 20
3 Setup ........................................................................................................................................... 21
3.1 Camera ......................................................................................................................... 21
3.1.1 Video ...................................................................................................................... 21
3.1.2 Audio ...................................................................................................................... 28
3.2 IVS Setup ..................................................................................................................... 29
3.2.1 Global Setup ......................................................................................................... 29
3.2.2 Scene Setup ......................................................................................................... 30
3.2.3 Rule Setup ............................................................................................................ 32
3.2.4 Parameter .............................................................................................................. 41
3.3 Network ......................................................................................................................... 43
3.3.1 TCP/IP ................................................................................................................... 43
3.3.2 Connection ............................................................................................................ 45
3.3.3 ONVIF .................................................................................................................... 46
3.3.4 PPPoE ................................................................................................................... 47
3.3.5 DDNS ..................................................................................................................... 48
3.3.6 IP filter .................................................................................................................... 49
3.3.7 SMTP （e-mail） ................................................................................................. 49
3.3.8 UPnP ...................................................................................................................... 51
3.3.9 SNMP ..................................................................................................................... 52
3.3.10 Bonjour ........................................................................................................... 53
3.3.11 Multicast ......................................................................................................... 54
3.3.12 IEEE802 ......................................................................................................... 55
3.3.13 Qos .................................................................................................................. 56
3.4 Event ............................................................................................................................. 57
3.4.1 Video detect .......................................................................................................... 57
3.4.2 Audio Detect ......................................................................................................... 62
3.4.3 Alarm ...................................................................................................................... 63
3.4.4 Abnormality ........................................................................................................... 65
3.5 Storage ......................................................................................................................... 67
3.5.1 Record schedule and snapshot schedule ........................................................ 67
3.5.2 Destination ............................................................................................................ 68
Dahua Network Speed Dome Web 3.0 Operation Manual
iii
3.5.3 Record control ...................................................................................................... 69
3.6 System .......................................................................................................................... 70
3.6.1 General .................................................................................................................. 70
3.6.2 Account .................................................................................................................. 72
3.6.3 PTZ ......................................................................................................................... 76
3.6.4 Default .................................................................................................................... 77
3.6.5 Import/Export ........................................................................................................ 78
3.6.6 Auto maintenance ................................................................................................ 78
3.6.7 Upgrade ................................................................................................................. 79
3.7 Information ................................................................................................................... 80
3.7.1 Version ................................................................................................................... 80
3.7.2 Log .......................................................................................................................... 80
3.7.3 Online User ........................................................................................................... 81
4 Alarm ........................................................................................................................................... 82
5 Log out ........................................................................................................................................ 83
Important
The following functions are for reference only. Some series products may not
support all the functions listed below.
Usually we recommend IE 7 or higher version. For those versions below IE 7, it
may not support the operation of some functions.
Dahua Network Speed Dome Web 3.0 Operation Manual
1
1 Network Connection
1.1 Preparation
This series speed dome product supports the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and
etc.
Please follow the steps listed below for network connection.
Make sure the speed dome has connected to the network properly.
Speed dome IP address and PC IP address shall be in the same network segment. If there is router,
please set the corresponding gateway and subnet mask.
Use order ping ***.***.***.***(* speed dome address) to check connection is OK or not.
1.2 Log in
Open IE and input speed dome address in the address bar.
For example, if your device IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 1-1.
Figure 1-1
The login interface is shown as below. See Figure 1-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here
Dahua Network Speed Dome Web 3.0 Operation Manual
2
Figure 1-2
If it is your first time to login in, system pops up warning information to ask you whether install control
webrec.cab or not. Please click OK button, system can automatically install the control. When system is
upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the
control download. Or you can lower the IE security level. See Figure 1-3.
Dahua Network Speed Dome Web 3.0 Operation Manual
3
Figure 1-3
1.3 Live Interface
After you logged in, you can see the live monitor window. Now you can operate the speed dome via the
WEB. See Figure 1-4.
Figure 1-4
There are six sections:
Section 1: Encode setup bar
Section 2: Window adjust bar
Section 3: System menu bar
Section 4: Window function option bar
Section 5: PTZ control
Section 6: PTZ function
1.4 Encode Setup
The encode setup interface is shown as in Figure 1-5.
Dahua Network Speed Dome Web 3.0 Operation Manual
4
Figure 1-5
Please refer to the following sheet for detailed information.
Parameter
Function
Main stream
In normal network width environment, main stream can record
audio/video file and realize network monitor.
Sub Stream 1
Connected to the Protocol, monitor or close the video under sub
stream 1 configuration. It can be used for network monitoring
instead of main stream when network bandwidth is not sufficient.
Sub Stream 2
Connected to the Protocol, monitor or close the video under sub
stream 2 configuration. It can be used for network monitoring
instead of main stream when network bandwidth is not sufficient.
Protocol
You can select video monitor protocol from the dropdown list.
There are three options: TCP/UDP/Multicast.
1.5 Video Window Setup
The interface is shown as in Figure 1-6.
Figure 1-6
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1
Image
adjustment
Click it to show or hide picture setup interface. See Figure
1-7. This interface is on the top right pane.
2
Original
size
Click this button to go to original size. It is to display the actual
size of the video. It depends on the resolution of the video.
3
Full screen
Click it to go to full-screen mode. Double click the mouse or
click the Esc button to exit the full screen.
4
Width and
height ratio
Click it to restore original ratio or suitable window.
Dahua Network Speed Dome Web 3.0 Operation Manual
5
5
Fluency
setup
There are three types: real-time/normal/fluency.
6
Rules info
Click it to enable live interface to display intelligent rules,
default is enable.
7
Open/close
PTZ
interface
Left click it to display or hide the PTZ control interface.
The picture setup interface is shown as in Figure 1-7.
Figure 1-7
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
Brightness setup icon. It is to adjust
monitor video brightness.
Note:
All the operations here
apply to WEB end
only.
Please go to Setup-
>Camera->Conditions
to adjust brightness,
contrast, hue and
saturation setup.
Contrast setup icon. It is to adjust
monitor video contrastness.
Saturation setup icon. It is to adjust
monitor video saturation.
Hue setup icon. It is to adjust
monitor video hue.
Reset
Restore brightness, contrastness
saturation and hue to system default
setup.
1.6 System Menu
System menu is shown as in Figure 1-8.
Dahua Network Speed Dome Web 3.0 Operation Manual
6
Please refer to chapter 1.3 Live, chapter 2 Playback, chapter 3 Setup, chapter 4Alarm, chapter 5 Log
out for detailed information.
Figure 1-8
1.7 Video Window Function Option
The interface is shown as below. See Figure 1-9.
Figure 1-9
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1
Remark
Click it and then select pen color, you can write down the
mark information on the preview interface.
2
Gesture
control
On the preview interface you can left click mouse to control
the PTZ and use the middle button to zoom in/zoom out.
3
Alarm
output
Click it to generate an alarm output and the button becomes
red. Click it again to stop alarm output.
There are two alarm output icons since this series product
supports two relay output.
Please note the alarm output interface may vary due to
different series products.
4
Digital
zoom
When video is in original status, click this button you can
select any zone to zoom in. After zoom in ,you can drag the
zoom in area in the specified area. Right click mouse system
restores original status. You can use the wheel to zoom out
the video.
5
Snapshot
You can snapshoot important video.
You can go to Setup->Camera->Video->Path to modify the
local record save path.
6
Triple snap
Click it, system can snap at 1f/s for three times. All images
are memorized in system storage folder.
7
Record
When you click local record button, the system begins
recording.
You can go to Setup->Camera->Video->Path to modify the
local record save path.
Dahua Network Speed Dome Web 3.0 Operation Manual
7
8
Manual
Track
Click it and then left click the mouse and drag the mouse in
the video window to select any zone, you can enable the
speed dome to auto track the object in the specified area.
Please note, you need to go to the Setup->IVS setup->Global
setup interface to enable IVS auto track function. Otherwise,
this function is null.
9
Audio
output
Turn on or off audio when you are monitoring.
You can go to Setup->Camera->Audio to set.
10
Bidirectional
talk
Click it to begin audio talk. You can go to Setup->Camera>Audio to set bidirectional talk mode.
11
Help
Click it to open help file.
1.8 PTZ Control
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please go to Setup>System->PTZ to set.).
Here you can view direction keys, speed, zoom, focus, iris button. See Figure 1-10.
PTZ direction: PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom
left/bottom right/ fast positioning.
Speed: The step 8 speed is faster than step 1.
Figure 1-10
Dahua Network Speed Dome Web 3.0 Operation Manual
8
1.9 Joystick
Figure 1-11
The function of joystick can be simulated by dragging the button in the middle, which can be used to
control the device rotation.
1.10 PTZ Setup/Menu
The PTZ setup/Menu interface is shown as in Figure 1-11.
Figure 1-11
Dahua Network Speed Dome Web 3.0 Operation Manual
9
Click PTZ set button, the interface is shown as in Figure 1-12.Here you can select scan, preset, tour
pattern, assistant function and etc.
Figure 1-12
Please refer to the following sheet for PTZ setup information.
Parameter
Function
Scan
Select Scan from the dropdown list, click Set button and then
control the PTZ to set the scan left limit and right limit. Start
button, you can begin scan operation. Default SN is 1.
Preset
Select Preset from the dropdown list, input the preset value and
then click Add button, now system save current position as one
preset. Click View button, the camera turns to the corresponding
position of the preset.
Tour
Select Tour from the dropdown list and then input tour value.
Click Add or Delete button to add/remove one preset from the
tour. Click Start button, you can begin tour.
Pattern
You can select Pattern from the dropdown list and then click
Add button, now you can operate PTZ to realize zoom, focus,
iris, direction operation and etc. Click Stop button to stop
memory pattern process. Click Start button to begin PTZ
movement.
Assistant
Input assistant value and click AUX on button to enable
corresponding assistant value. Click AUX off button to disable
assistant function.
Dahua Network Speed Dome Web 3.0 Operation Manual
10
Parameter
Function
Goto
It is the accurate positioning function. Please input
corresponding horizontal angle, tilt angle, and speed dome
zoom speed and then click Goto button to go to a specified
position.
One unit of the horizontal angle or tile angle stands for 0.1
degree.
Pan
Select Pan from the dropdown list and then click Start button, you
can turn the PTZ realize 360 degrees movement. Click Stop button
to stop current operation.
Dahua Network Speed Dome Web 3.0 Operation Manual
11
2 Playback
The playback of WEB client end supports two modes which are video playback and picture playback.
Note:
It needs to set “3.5 Storage Management” before operating playback.
2.1 Video Playback
The video playback interface of WEB client end includes the following six functions:
Parameter
Note
1
Play function
2
Playback file
3
Playback clip
4
Record type
5
Progress bar
6
Aux function
Figure 2-1
Dahua Network Speed Dome Web 3.0 Operation Manual
12
2.1.1 Play Function
Figure 2-2
Parameter
Note
① Play
When it displays this button, it means stop playing or not playing video. Click it to
switch to normal playing status.
② Stop
Click it to stop playing current video.
③ Next frame
Click it to play next frame.
Note:
It needs to pause playback when using next frame function.
④ Slow
Click it to make it play slowly.
⑤ Fast
Click it to make it play fast.
⑥ Quiet
It is mute when it displays this button, Click it to restore audio function.
⑦ Volume
Click the left mouse button to adjust the playback volume.
2.1.2 Playback File
The blue date in the calendar means that there is video or snapshot file on the current day.
Dahua Network Speed Dome Web 3.0 Operation Manual
13
Figure 2-3
Parameter
Note
File type
Select “dav” to playback video.
Select “jpg” to playback picture.
Data source
The default is SD card.
Step 1
Click the blue date, the time line will display the record file progress bar with colors. Green represents
general record; yellow represents motion record; red represents alarm record; blue represents manual
record.
Step 2
Click a certain time location of the record file progress bar area, the playback interface will play the
record file from that time.
Figure 2-4
Step 3
Click file list , the record file of selected date will display in the list.
Step 4
Dahua Network Speed Dome Web 3.0 Operation Manual
14
Double click the file in the list, and it will playback the file, meanwhile it will also display file size, begin
time and end time.
Figure 2-5
Parameter
Note
Search
It is to search all the record file between begin time and end
time of the selected date.
Download
Format
Two formats to select: dav and mp4.
Dahua Network Speed Dome Web 3.0 Operation Manual
15
Parameter
Note
Download
When record type is “dav”, click download button to download the file to
local.
When record type is “mp4”, click download button to download file to 3.1.15.
Storage path.
Note:
The system doesn’t support download and playback record of MP4 format at the
same time.
Back
Click it to go back to calendar interface to select date again.
2.1.3 Playback Cut
Note:
When using playback cut function, the record file which is being playbacked will stop playing
automatically, which means that playback cut and playback can’t be done at the same time.
Step 1
Click the begin time of playback cut on the timeline, and the time needs to be within the range of
progress bar area of the record file.
Step 2
Move the mouse to the top of the clip icon , it will display “Select Begin Time” on the lower right
corner. Click cut icon , and finish the setting of begin time of playback clip.
Step 3
Click the end time of playback cut on the timeline, and the time needs to be within the range of progress
bar area of the record file.
Step 4
Move the mouse to the top of the cut icon ; it will display “Select End Time” on the lower right
corner. Click cut icon , and finish the setting of end time of playback cut.
Step 5
Click “Save” to edit the file to 3.1.1.5 storage path.
Figure 2-6
Dahua Network Speed Dome Web 3.0 Operation Manual
16
2.1.4 Record Type
After checking record file type, it will only display the selected type of file in the progress bar and file list.
Figure 2-7
2.1.5 Progress Bar Time Format
Figure 2-8
Parameter
Note
24 hour button
Click the button and the progress bar will display in 24-hour mode.
2 hour button
Click the button and the progress bar will display the record file within 2
hours range.
1 hour button
Click the button and the progress bar will display the record file within 1
hour range.
30 min button
Click the button and the progress bar will display the record file with30
minutes range.
2.1.6 Aux Function
Figure 2-9
Parameter
Note
Regional Zoom
Click the button to select any area to zoom when the playback video
is in the original state, it can drag and zoom the area in a certain
range when it is in the non-original state, click the right mouse button
to restore the original state.
Click the button and zoom the image size by rolling the mouse wheel.
Snapshot
Click the button and snapshot the playback video, the image will be
stored in the path 3.1.1.5.
Dahua Network Speed Dome Web 3.0 Operation Manual
17
2.2 Picture Playback
The picture playback interface of WEB client includes following three functions.
Parameter
Note
1
Play function
2
Playback file
3
Snapshot type
Figure 2-10
2.2.1 Play Function
Dahua Network Speed Dome Web 3.0 Operation Manual
18
Figure 2-11
The default icon is , which means stopping playing or not playing pictures.
Click play button and switch to normal play state, at this moment, the icon displays as .
Click pause button and switch to pause play state.
2.2.2 Playback File
Figure 2-12
Dahua Network Speed Dome Web 3.0 Operation Manual
19
Figure 2-13
Step 1
Click file list , the snapshot file of selected date will display in the list.
Step 2
Double click the file in the list, it will playback the snapshot picture.
Parameter
Note
Search
It is to search all the snapshot file between begin time and end
time of the selected date.
Download
Click “Download” button and download the snapshot file to local.
Back
Click it to go back to calendar interface to select time again.
Dahua Network Speed Dome Web 3.0 Operation Manual
20
2.2.3 Snapshot Type
After checking snapshot type, it will only display the selected type of file in the file list.
Figure 2-14
Dahua Network Speed Dome Web 3.0 Operation Manual
21
3 Setup
3.1 Camera
3.1.1 Video
3.1.1.1 Video bit stream
The video bit stream interface is shown as below. See Figure 3-1.
Figure 3-1
Please refer to the following sheet for detailed information.
Parameter
Function
Main
stream
Bit stream type
It includes general stream, motion stream and alarm
stream. You can select different encode frame rates for
different recorded events.
The frame rates of the motion detect and alarm is
customized.
Encode mode
There are four options: H.264, H.264H, and MJPEG
encode mode.
H.264 : Main Profile encode mode.
H.264H: High Profile encode mode.
MJPEG: In this encode mode, the video needs
general large bit stream to guarantee the video
definition. You can use the max bit stream value in
the recommend bit to get the better video output
effect.
Dahua Network Speed Dome Web 3.0 Operation Manual
22
Parameter
Function
Resolution
There are multiple resolutions. You can select from the
dropdown list.
For each resolution, the recommended bit stream value
is different.
Frame Rate
(FPS)
PAL: 1～25f/s，NTSC: 1～30f/s.
Bit Rate Type
There are two options: VBR and CBR.
Please note, you can set video quality in VBR mode.
In MJPEG mode, the bit stream control mode can only
be CBR.
Recommended
Bit
Recommended bit rate value according to the resolution
and frame rate you have set.
Bit Rate
In CBR, the bit rate here is the average value. Usually
it goes up and down between 10%.
It is the max value in VBR mode. When the scene is
not complicated, the bit value may be lower than you
set.
I Frame
Here you can set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50.
Recommended value is frame rate *2.
Important
I frame interval setup is null if it is the MJPEG
encode mode.
SVC
Frame rate can be encoded by layer. It is a flexible
encoding method. By default, it is 1 as 1 layer. You also
can set 2/3/4 layers.
Watermark
This function allows you to verify the video is tampered
or not.
The max length is 128-digit. The character can only
include number, character, underline and hyphen.
Sub
stream
Sub Stream
Enable
If check the enable box here to enable or disable sub
stream, it is enabled by default.
It supports enable two sub streams at the same time:
sub stream 1, sub stream 2.
Bit stream type
General bit stream.
Dahua Network Speed Dome Web 3.0 Operation Manual
23
Parameter
Function
Encode mode
There are four options: H.264, H.264H, and MJPEG
encode mode.
H.264 : Main Profile encode mode.
H.264H: High Profile encode mode.
MJPEG: In this encode mode, the video needs
general large bit stream to guarantee the video
definition. You can use the max bit stream value in
the recommend bit to get the better video output
effect.
Resolution
There are multiple resolutions. You can select from the
dropdown list.
For each resolution, the recommended bit stream value
is different.
Frame Rate
(FPS)
PAL: 1～25f/s，NTSC: 1～30f/s.
Bit Rate Type
There are two options: VBR and CBR.
Please note, you can set video quality in VBR mode.
Recommended
Bit
Recommended bit rate value according to the resolution
and frame rate you have set.
Bit Rate
In CBR, the bit rate here is the average value. Usually
it goes up and down between 10%.
It is the max value in VBR mode. When the scene is
not complicated, the bit value may be lower than you
set.
I Frame
Here you can set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50.
Recommended value is frame rate *2.
Important
I frame interval setup is null if it is the MJPEG
encode mode.
Frame rate can be encoded by layer. It is a scalable
encoding method. By default, it is 1 as 1 layer. You also
can set 2/3/4 layers.
3.1.1.2 Snapshot
The snapshot interface is shown as in Figure 3-2.
Loading...