Dahua N84BG44(I) Quick Start Manual

Network Eyeball Camera

N84BG44(I)

Quick Start Guide

Version 001.001

Dahua Technology USA Inc.

Table of Contents

1 Welcome .......................................................................................................................... 1

1.1 Important Safeguards and Warnings .................................................................. 1

Electrical safety ................................................................................................... 1

Environmental Precautions ................................................................................. 2

Operation and Daily Maintenance ...................................................................... 3

Warnings ............................................................................................................. 3

1.2 FCC Information .................................................................................................. 4

FCC compliance： .............................................................................................. 4

1.3 Legal Notices ...................................................................................................... 4

Copyright ............................................................................................................. 4

Trademarks ......................................................................................................... 4

1.4 Disclaimer ........................................................................................................... 5

2 Unpacking ........................................................................................................................ 6

3 Installation and Configuration .......................................................................................... 7

3.1 Camera Configuration and Cables ..................................................................... 7

3.2 Framework and Dimensions ............................................................................... 8

3.3 Locally Storing Data ............................................................................................ 8

4 Device Installation ........................................................................................................... 9

4.1 Installing the Camera .......................................................................................... 9

5 Network Configuration ................................................................................................... 11

5.1 Network Protocols ............................................................................................. 11

5.2 Modifying the IP Address .................................................................................. 12

5.3 Using the ConfigTool ........................................................................................ 12

5.4 Accessing the Web Interface ............................................................................ 13

5.5 Configuring Local SD Card Recording ............................................................. 14

1 Welcome

This manual offers reference material and general information about the basic operation,

maintenance, and troubleshooting of the Dahua Multi-Sensor Panoramic Camera. Read, follow, and

retain the following safety instructions. Heed all warning on the unit and in the operating instructions

before operating the unit. Keep this guide for future reference.

1.1 Important Safeguards and Warnings

Electrical safety

 Install the unit in accordance with the manufacturer’s instructions and in accordance with

applicable local codes.

 All installation and operation must conform to your local electrical safety codes.

 Do not overload outlets and extension cords, which may cause fire or electrical shock.

 Do not place the camera near or in a place where the camera may contact overhead power lines,

power circuits, or electrical lights.

 Ensure power conforms to SELV (Safety Extra Low Voltage) and that the limited power source is

rated AC 24V as specified in IEC60950-1. (Power supply requirement is subject to the device

label).

 All input/output ports are SELV circuits. Ensure that SELV circuits are connected only to other

SELV circuits.

 Ground the unit using the ground connection of the power supply to protect the unit from damage,

especially in damp environments.

 Protect the plug and power cord from foot traffic, being pinched, and its exit from the unit.

 Units with or without an ON/OFF switch have power supplied to the unit whenever the power

cord is inserted into the power source; however, the unit is operational only when the ON/OFF

switch is in the ON position. The power cord is the main power disconnect device for switching

off the voltage for all units.

 Operate the unit only from the type of power source indicated on the label. Before proceeding,

disconnect the power from the cable to be installed into the unit.

 For external power supplied units, use only the recommended or approved power supplies.

 Limited power sources must comply with EN 60950. Substitutions may damage the unit or

cause fire or shock.

 For 24 VAC units, voltage applied to the unit’s input power should not exceed ±25%. User-

supplied wiring must comply with local codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit’s power supply terminal.

 Contact the local dealer or the power company to verify the correct power supply.

 Do not supply power via the Ethernet connection (PoE) when power is already supplied via the

power connector.

 Do not attempt to service the unit. Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified personnel.

1

 If the unit is damaged and requires service, unplug the unit from the main AC power supply and

from the PoE supply and refer to qualified service personnel. Damage may include, but is not

limited to:

 The power supply cord or plug is damaged.

 Liquid has spilled in or on the unit.

 An object has fallen on the unit.

 The unit has been dropped and the housing is damaged.

 The unit displays a marked change in performance.

 The unit does not operate in the expected manner when the user correctly follows the proper

operating procedures.

 Ensure a service technician uses replacement parts specified by the manufacturer, or that have

the same characteristics as the original parts. Unauthorized parts may cause fire, electrical

shock, or other hazards. Dahua is not liable for any damage or harm caused by unauthorized

modifications or repairs.

 Perform safety checks after completion of service or repairs to the unit.

 Use attachments and accessories only specified by the manufacturer. Any change or

modification of the equipment, not expressly approved by Dahua, could void the warranty.

 Incorporate a readily accessible disconnect device in the building installation wiring for quick

power disconnect to the camera.

 Dahua assumes no liability or responsibility for any fire or electrical shock caused by improper

handling or installation.

Environmental Precautions

 Do not aim the unit at a strong light source or into direct sunlight to focus. A strong light source

may cause overexposure and may affect the longevity of the CCD or the CMOS sensor.

 Transport, use, and store the unit within the specified temperature and humidity range.

 Do not place the unit in a wet, dusty, extremely hot or an extremely cold environment; and avoid

environments with strong electromagnetic radiation or unstable lighting.

 Never push objects of any kind into this unit through openings as they may touch dangerous

voltage points or cause a short circuit that may result in fire or electrical shock. Take care to not

spill any liquid on the unit.

 Do not use units intended for indoor applications near water, in damp or wet environments, or in

any area classified as a wet location. Do not expose an indoor unit to rain or moisture to reduce

the risk of fire or electric shock.

 Do not block or cover any openings in the unit enclosure. These openings are provided for

ventilation to prevent overheating and to ensure reliable operation. Ensure the unit is placed in

an area with adequate ventilation.

 Do not place the unit near a heat source such as heaters, stoves, radiators or other equipment

that produces heat.

 Pack the unit with standard factory packaging or material of the same quality when transporting

the unit.

 Take care to avoid heavy stress, violent vibration, or water spills to the camera unit during

transportation, storage, and installation.

2

Operation and Daily Maintenance

 Do not touch the heat dissipation component of the unit. This part of the unit is hot and may

cause a burn.

 Do not open or dismantle the device; there are no components that a user can fix or replace.

Opening the unit may cause water leakage or expose components to direct light. Contact the

manufacturer or a qualified service representative to service the camera or to replace a

component, including the desiccant.

 Dahua recommends the use of a thunder-proof device in concert with the unit.

 Do not touch the CCD or the CMOS optic sensor. Use a blower to clean dust or dirt on the lens

surface. Use a dry cloth dampened with alcohol and gently wipe away any dust on the lens.

 Use a dry soft cloth to clean the unit’s housing. If the unit is particularly dusty, use water to dilute

a mild detergent, apply the diluted detergent to a soft cloth, then gently clean the device. Finally,

use a dry cloth to wipe the unit dry. Do not use a volatile solvent like alcohol, benzene, or thinner;

or use a strong detergent with abrasives, which may damage the surface coating or reduce the

working performance of the unit.

 Do not touch or wipe a dome cover during installation, this cover is an optical device. Refer to

the following methods clean the dome cover:

 Stained with dirt: Use an oil-free soft brush or blower to gently remove the dirt.

 Stained with grease or fingerprints: Use a soft cloth to wipe gently the water droplet or the oil

from the dome cover. Then, use an oil-free cotton cloth or paper soaked with alcohol or

detergent to clean the lens from the center of the dome to outside. Change the cloth several

times to ensure the dome cover is clean.

Warnings

 Change the default password after the initial login to protect the integrity of the network.

 Use the standard accessories provided by the manufacturer and ensure the unit is installed and

commissioned by qualified professionals.

 Protect the lens area from laser radiation when using a laser device to aid in installation and

leveling of the unit.

 Do not supply power via the Ethernet connection (PoE) when power is already supplied via the

power connector.

3

1.2 FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

 This device may not cause harmful interference;

 This device must accept any interference received, including interference that may cause

undesired operation.

FCC compliance：

This equipment has been tested and found to comply with the limits for a digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio

communication. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

1.3 Legal Notices

Copyright

This user guide is ©2016, Dahua Technology Company, LTD.

This user guide is the intellectual property of Dahua Technology Company, LTD and is protected by

copyright. All rights reserved.

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

4

1.4 Disclaimer

 This user guide has been compiled with great care and the information it contains has been

thoroughly reviewed and verified. The text was complete and correct at the time of printing. This

guide may be periodically updated to reflect changes to the product or to correct previous

information and the content of this guide can change without notice. If you encounter an error or

have any questions regarding the contents of this guide, contact customer service for the latest

documentation and supplementary information. Dahua accepts no liability for damage resulting

directly or indirectly from faults, incompleteness, or discrepancies between this guide and the

product described. Dahua is not liable for any loss caused by installation, operation, or

maintenance inconsistent with the information in this guide.

 Video loss is inherent to all digital surveillance and recording devices; therefore Dahua cannot be

held liable for any damage that results from missing video information. To minimize the

occurrence of lost digital information, Dahua recommends multiple, redundant recording systems,

and adoption of backup procedure for all data.

 Contact the supplier or customer service if you encounter any issue while using this unit.

5

2 Unpacking

This equipment should be unpacked and handled with care. If an item appears to have sustained

damage during shipping, notify the shipper immediately.

Verify that all the parts listed below are included. If an item is missing, contact customer support or

your local representative.

The original packing carton is the safest container to transport the unit, in the event the unit must be

returned for service. Retain the carton and all shipping material for future use.

Please refer to the enclosed CD for more details, to view the detailed User’s Manual, and for

configuration software.

Package Item Quantity

Network Camera 1
Mounting Template 1
Installation Hardware Pack 1

Expansion Bolts 3
Screws 3

Hex Key 1
Waterproof Network Connector 1
Quick Start Guide 1
Documentation CD 1

6

3 Installation and Configuration

3.1 Camera Configuration and Cables

The following figure depicts the type and location of camera controls and cables coming from the

device. This image is intended as a reference only.

Figure 3-1

No. Description

1 Dome enclosure

1 Dome pedestal

Figure 3-2

No. Port Connector Description

Connect to standard Ethernet cable.

3 LAN Ethernet

4 Power 12 VDC Power

Note: Certain devices support Power over
Ethernet. Check the specific device to determine if
the device accepts PoE and use an appropriate
Ethernet cable and network to supply power.

Power port. Input DC 12V power supply.
Use power according to the device tag.

7

3.2 Framework and Dimensions

The following figures show the dimensions of the device in mm (in.). These images are intended

as a reference only.

Figure 3-3

3.3 Locally Storing Data

Certain cameras include a SDHC card slot for onboard storage that support a 128 GB Micro SD card.

Dahua recommends using a SanDisk Extreme Micro SD card (or an equivalent substitute) as these

cards have been fully tested without issue and the SanDisk Extreme line is better suited for constant

recording. Lower-grade SD cards meant for multimedia applications will, at times, have questionable

quality and reliability. 

Recording to the SD card is first in first out (FIFO). The camera deletes the oldest (first) entry as new

storage requirements arise. The camera does not signal nor make an indication when data is deleted.

Storage time is dependent on a variety of factors such as SD card size, image resolution and video

frames per second. 

SD Recording supports video only. Audio is not supported. 

8

4 Device Installation

This section details installing the camera to a wall or to a ceiling. Note that the wall or ceiling must be

capable of supporting a minimum of three times the weight of the camera and a bracket (if used). DO

NOT connect the camera to the power supply during installation.

Figure 4-1

4.1 Installing the Camera

1. Remove the camera, the mounting template, and the hardware package from the box.

2. Loosen the locking screw from the front of the camera; then pull the dome enclosure down to

disconnect the enclosure from the pedestal.

3. Determine the route of the power and the Ethernet cables.

 Bottom wiring exit through the installation medium:

Figure 4-2

 Side wiring exit

Figure 4-3

9

4. Insert a MicroSD card into the SD Card Slot.

5. Apply the mounting template to the installation medium. Pre-drill the three perimeter holes as

marked on the template for the expansion bolts, using a drill bit that is no wider than the

expansion bolt. If you route the cable through the installation medium, then drill the center hole.

6. Insert an expansion bolt into each pre-drilled perimeter hole.

7. Attach the waterproof network connector if the camera is used outdoors.

Figure 4-4

a. Place the wide side of the rubber ring onto the end of the network cable extending out from

the camera.

b. Pull the waterproof cable end without the Ethernet connector through the body of the

Waterproof Connector. Thread the cable through the Fixing Rubber Ring and the Waterproof

Locking Cover.

c. Attach the male Ethernet connector to the network cable coming from the camera. Ensure the

Waterproof Connector shroud covers the Ethernet connection.

d. Connect the other end of the waterproof connector to the network port and rotate it clockwise

to lock the network port and waterproof connector firmly.

e. Slide the Waterproof Locking Cover over the main body of waterproof connector and rotate it

clockwise to seal the connection.

8. Align the three holes on the camera pedestal with the expansion bolts. Ensure the cable exit port

on the pedestal is in the correct position, if you plan to route the cables through the side exit.

9. Route the cables from the bottom of the camera through the installation medium or through the

side exit on the pedestal.

10. Secure the camera pedestal to the installation medium with the three screws.

11. Connect the external cables from the camera to the appropriate cables for Ethernet and power.

12. Supply power to the camera.

13. Place the dome enclosure onto the pedestal and secure with the locking screw.

10

5 Network Configuration

Dahua IP cameras feature a built-in Web interface to control all aspects of camera operation. This

section includes details about the supported network protocols, configuring IP addresses, and

configuring alarms and local recording options. Refer to the camera’s Operations Manual for full

details.

5.1 Network Protocols

Dahua cameras support RTSP, RTP/TCP, RTP/UDP, HTTP, DHCP, TFTP, QoS, IP version 4 (IPv4)

and IP version 6 (IPv6).

RTSP – Cameras communicate with video management systems over Real Time Streaming Protocol.

Do not change the RTSP port unless you are sure your VMS does not use the default setting.

RTP/TCP – The Real-time Protocol/Transmission Control Protocol is best suited for applications that

require high reliability, and transmission time is relatively less critical.

RTP/UDP – The Real-time Protocol/User Datagram Protocol is used for live unicast video, especially

when it is important to always have an up-to-date video stream, even if some images are dropped.

HTTP – The Hypertext Transfer Protocol is an application protocol for distributed, collaborative,

hypermedia information systems.

DHCP – The Dynamic Host Configuration Protocol allows network administrators to centrally manage

and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP

address notification, or if the DHCP can update a DNS server.

TFTP – The Trivial File Transfer Protocol is a simple, lock-step, File Transfer Protocol which allows a

client to get from or put a file onto a remote host. TFTP lacks security and most of the advanced

features offered by more robust file transfer protocols such as File Transfer Protocol.

QoS – Quality of Service guarantees a certain level of a specified resource to selected traffic on a

network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by

controlling the amount of bandwidth an application may use.

IPv4 – The IPv4 (IP version 4) is enabled by default and obtains the IP address automatically. The

address can be used to allow or block network traffic that matches a specified address or protocol.

The IP address must be valid for the network. For more information, contact your network

administrator.

IPv6 – A typical IPv6 (IP version 6) node address consists of a prefix and an interface identifier (total

128 bits). The prefix is the part of the address where the bits have fixed values or are the bits that

define a subnet. A typical IPv6 address may resemble the following example: 2001:db8: :52:1:1. The

IP address must be valid for the network. Before making changes to the IPv6 address, consult with

your network administrator.

11

5.2 Modifying the IP Address

To operate the camera in your network you must assign it a valid network IP address. The default IP

address is 192.168.1.108, but you may have to change this address if it conflicts with another device

on the network.

To properly configure the camera for your network, you need the following information:

 Camera IP address – This address is an identifier for the camera on an IP network. For example,

140.11.2.115 is valid syntax for an IP address.

 Subnet mask – A mask is used to determine the subnet an IP address belongs to.

 Gateway IP address – This address is a node on a network that serves as an entrance to

another network.

 Port – A port is an endpoint to a logical connection in an IP network.

Dahua supplies the ConfigTool to access and to modify the network settings of a device. Refer to the

Operation Manual, available on the CD included with the camera or on Dahuasecurity.com, for

complete information.

Notes:

 Ensure that the network parameters of each camera is available before starting configuration.

 The ConfigTool supports those cameras that are part of the same network that as the computer

running the ConfigTool.

5.3 Using the ConfigTool

1. Install the ConfigTools.exe on a computer.

2. Adjust the computer’s network settings so that it is on the same network as the camera.

3. Launch the ConfigTool to generate a list of devices on the network.

4. Double click the device to be configured, the ConfigTool opens the Login dialog box for the device.

5. Enter the IP address, Username, Password, and Port number of the camera, then click OK. Note:

the default Username and Password for the device is “admin” and “admin” respectively. The

default port is 37777.

Figure 5-1

12

6. Click the Net icon at the top of the ConfigTool.

7. Modify the IP Address and any other applicable network parameter.

8. Click Save to finish modification and store the modified network parameters.

Figure 5-2

5.4 Accessing the Web Interface

Each camera can be accessed directly from the Internet Explorer Web browser. The Web Interface

allows you to set camera parameter, configure alarm inputs and outputs, view live camera images,

and review recorded video.

Note: Different devices may have different Web interfaces, the figures below are for reference only,

and may not represent the Web Interface for your camera. Refer to the Web Operation Manual,

included on the CD shipped with the camera, for more details.

1. Launch Internet Explorer and type the modified camera IP address in the address bar. Internet

Explorer opens the Login page.

2. Type the Username and Password for the camera. (The default Username and Password is

”). Then, click Login.

“admin

Figure 5-3

13

3. Install the controls according to the system prompt. Once the controls are installed IE displays the

Web Interface main page.

4. Modify the administrator password as soon as possible after you successfully logged in.

5.5 Configuring Local SD Card Recording

The devices Web interface contains settings to control the recording medium and to configure an

alarm that triggers once the Micro SD card passes a pre-determined storage.

1. Access the Web Interface for the device and click the Setup tab. Expand the Storage menu, then

choose the Destination page.

Figure 5-4

2. Select the recording medium for each event Recorded and Snapshot event, Scheduled, Motion

Detect and Alarm. Select the Local check box to record an event to the Micro SD card.

3. Click the Local tab to view the used capacity and the total capacity of the Micro SD card.

Figure 5-5

14

4. Expand the Event menu, located at the left of the Web interface, then select the Abnormality page

to set alarms related to the Micro SD card. The contains the following Micro SD card alarm

options:

 No SD Card: Device triggers an alarm if the device does not contain a Micro SD card.

 Capacity Warning: Device triggers an alarm when the data on the Micro SD card passes a

defined threshold.

 SD Card Error: Device triggers an alarm if it detects an issues writing data or retrieving data

from the Micro SD card.

Figure 5-6

5. Select the event from the Event Type pull-down menu (No SD Card, Capacity Warning, SD Card

Error).

6. Check the Enable box to activate the alarm for this event.

7. Check the Relay-out box to enable a relay alarm. Then, specify the time in seconds to delay the

alarm relay output (10 s to 300 s).

8. Check the Send Email box to send an email to a specified user after the device triggers an alarm.

9. Set the capacity limit for the Micro SD Card (available with the Capacity Warning event type). The

device triggers an alarm once the amount of data on the card surpasses this limit.

Figure 5-7

15

Dahua Technology USA Inc.

23 Hubble, Irvine, CA 92618

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Rev 001.001 © 2016 Dahua. All rights reserved. Design and specifications are subject to change without notice.

16