Page 1
HD IR Waterproof Fixed IP Camera （With Integrated Bracket）
User’s Manual
Version 3.2.3
Page 2
i
Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Page 3
ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. This series product can not support these
two modes at the same time.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Page 4
iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
IPC Unit 1
Quick Start Guide 1
12V to 24V Conversion Cable
(For AC 24V series product only)
1
Installation Accessories Bag 1
CD 1
Page 5
iv
Table of Contents
1 General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup...........................................................................................4
2 Structure ....................................................................................................................................11
2.1 Multiple-function Combination Cable ......................................................................11
2.2 Framework and Dimension.......................................................................................12
2.3 Bidirectional talk .........................................................................................................13
2.3.1 Device-end to PC-end ........................................................................................13
2.3.2 PC-end to the Device-end..................................................................................13
2.4 Alarm Setup.................................................................................................................13
3 Device Installation ....................................................................................................................15
4 Quick Configuration Tool.........................................................................................................16
4.1 Overview......................................................................................................................16
4.2 Operation .....................................................................................................................16
5 Web Operation..........................................................................................................................19
5.1 Network Connection...................................................................................................19
5.2 Login and Logout........................................................................................................19
6 FAQ ............................................................................................................................................22
Appendix Toxic or Hazardous Materials or Elements ...............................................................23
Page 6
1
1 General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts audio
and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series IPC uses standard H.264 video compression technology and G.711a audio compression
technology, which maximally guarantee the audio and video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in protection enclosure and waterproof design conforms to the IP 66 level. It has the sound
waterproof function suitable for use in the outdoor environments.
It supports real-time monitor and listening at the same time. It supports analog video output and dual-
way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
IPC is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
z Different user rights for each group, one user belongs to one group.
z The user right shall not exceed the group right.
Storage
Function
z Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
z Support record via Web and the recorded file are storage in the client-end PC.
z Support built-in SD card.
z Do not support local SD card hot swap storage function. Support short-time
storage when encounter disconnection.
z Support network storage function such as FTP.
Alarm
Function
z Real-time respond to external on-off alarm input, and video detect as user pre-
defined activation setup and generate corresponding message in screen and
audio prompt(allow user to pre-record audio file)
z Real-time video detect: motion detect, camera masking.
Network
Monitor
z IPC supports one-channel audio/video data transmit to network terminal and then
decode. Delay is within 270ms (network bandwidth support needed)
z Max supports 20 connections.
z Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
z Support web access.
Network
Management
z Realize IPC configuration and management via Ethernet.
z Support device management via web or client-end.
Power
z External power adapter DC12V/AC 24V. You can select according to your actual
environments. Please note system can not support these two types of power
supplying at the same time.
Assistant
Function
z Log function
z Support system resource information and running status real-time display.
z Day/Night mode auto switch.
Page 7
2
z Built-in IR light. Support IR night vision.
z Support picture parameter setup such as electronic shutter and gain setup.
z Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
z Support video watermark function to avoid vicious video modification.
z The enclosure conforms to the IP 66 protection. Has the waterproof function.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for IPC performance specification.
Model
Parameter
IPC-HFW3300C IPC-HFW3200C
IPCHFW3100C
IPCHFW3101C
Main Processor TI Davinci high performance DSP
OS Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User Interface Remote operation interface such as WEB, DSS, PSS
System
System Status SD card status, bit stream statistics, log, and software version.
Image Sensor
1/2.8-inch
CMOS
1/2.8-inch CMOS 1/3-inch CMOS 1/3-inch CMOS
Pixel 2080(H)*1553(V) 1920(H)*1080(V) 1280(H)*960(V) 1280(H)*960(V)
Day/Night Mode
Support day/night mode switch and IR-CUT at the same time. (The lens
has built-in IR-CUT mechanical component.).
Auto Aperture DC drive
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC On/Off On/Off On/Off
Off/BLC/WD
（Value:1100）
Exposure Mode
Manual/Auto
PAL: It ranges from 1/3 to 1/10000
NTSC: It ranges from 1/4 to 1/10000
Video
Compression
Standard
H.264/JPEG/MJPG
Video Parameter
Video Frame
Rate
PAL:
Main stream
（3M@15fps,10
80P@25fps,SXG
A@25fps,
1.3M@25fps、
720P@25fps、
704*576@25fps
）
Extra stream
(704*576@25fp,
352*288@25fps)
PAL:
Main stream
（1080P@25fps,
SXGA@25fps,
1.3M@25fps,
720P@25fps,
704*576@25fps
），
Extra stream
(704*576@25fps,
352*288@25fps)
）
PAL：
Main stream
（1.3M@25f，
720P@25fps，
704*576@25fp
s）
Extra stream
(704*576@25fp
s，
352*288@25f
ps)
PAL：
Main stream
（1.3M@25fps,
720P@25fps，
704*576@25fp
s）
Extra stream
(704*576@25fp
s，
352*288@25f
ps)
Page 8
3
NTSC:
Main stream
（3M@15fps ,10
80P@30fps,
SXGA@30fps,
1.3M@30fps,
720P@30fps,
704*480@30fps
），
Extra stream
（704*480@30f
ps,352*240@30f
ps）
NTSC:
Main stream
（1080P@30fps,
SXGA@30fps,
1.3M@30fps,
720P@30fps,
704*480@30fps
），
Extra stream
（704*480@30fp
s,352*240@30fps
）
NTSC:
Main stream：
（1.3M@30fps,
720P@30fps,
704*480@30fp
s）
Extra stream
（704*480@30f
ps,352*240@3
0fps）
NTSC:
Main stream：
（1.3M@30fps,
720P@30fps,
704*480@30fp
s）
Extra stream
（704*480@30
fps,352*240@3
0fps）
Video Bit Rate
H.264: 56Kbps-8192Kbps.
ＭJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, camera masking.
Lens 3.3-12mm@F1.4
2.812mm@F1.4
Lens Interface
Φ14 interface. Lens is the default accessories
Audio Input
1-channel. RCA
Audio Output
1-channel. RCA
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit Rate 16kbps 16BIT
Audio
Audio
Compression
Standard
G.711a/G.711u/PCM
Video
Motion Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event: alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
2-channel input，1-channel output
Record Priority Manual>External alarm >Video detect>Schedule
Local Storage Support Micro SD card storage
Record and
Backup
Storage
Management
Support display local storage status
Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.
Network
Remote
Operation
Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade and etc.
Video Output
1-channel analog video output，BNC port.
AUX
Interfac
e
Restore Default
Setup
Reset button
Page 9
4
Power
Support AC24V/DC12V power. (Can not support these two modes at the
same time.)
Power
Consumption
8W MAX (10W MAX when ICR switch)
Working
Temperature
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(mm)
φ104*306.7
Weight
1250g（Excluding box）
General Parameter
Installation Bracket is included in the accessories bag.
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
Brightness 50
Contrast 50
Hue 50
Saturation 50
Gain Mode Auto
Gain Adjust 80
Exposure Mode Auto
Auto Iris On
Scene Mode Auto
Day/night Mode Auto
BLC Off Off Off WDR
Mirror Off
Conditions
Flip Off
Bit stream
type
General
Encode
mode
H.264
Resolution
1080P
（1920*1080
）
1080P
（1920*1080
）
1.3M
（1280*960
）
720P
（1280*720
）
Frame Rate
（FPS）
PAL:25
NTSC:30
Bit Rate
Type
CBR
Recommen
ded Bit
3584-8192 Kb/S
Bit Rate 8192
I Frame 50
Camera
Video
Video bit stream
Main
Stream
Watermark
Enable
Page 10
5
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
Watermark
character
DigitalCCTV
Enable Enable
Bit stream
type
General
Encode
mode
H.264
Resolution
PAL:CIF(352*288)
NTSC:CIF(352*240)
Frame Rate
（FPS）
PAL:25
NTSC:30
Bit Rate
Type
CBR
Recommen
ded Bit
192-1024Kb/S
Bit Rate 1024
Sub
Stream
I Frame 50
Snapshot
Type
General
Image Size
1080P
（1920*1080
）
1080P
（1920*1080
）
1.3M
（1280*960
）
720P
（1280*720
）
Quality 5
Snapshot
Interval 1s
Privacy
Mask
Disable
Channel
Title
Enable
Video Overlay
Time Title Enable
Snapshot
Path
C:\PictureDownload
Path
Record Path C:\RecordDownload
Enable Enable
Main Stream
Encode
Mode
G.711A
Enable Disable
Audio
Sub Stream
Encode
Mode
G.711A
Host Name IPC
Ethernet
Card
Wire(Default)
Mode Static
Network
TCP/IP
Mac
Address
Device MAC address when it is shipped out of the factory
Page 11
6
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
IP Version IPV4
IP Address 192.168.1.108
Subnet
Mask
255.255.255.0
Default
Gateway
192.168.1.1
Preferred
DNS
8.8.8.8
Alternate
DNS
8.8.8.8
Enable
ARP/Ping
set device
IP address
service
Enable
Max
Connection
10
TCP Port 37777
UDP Port 37778
HTTP Port 80
Connection
RTSP Port 554
Enable Disable
Username none
PPPoE
Password N/A
Server Type Disable，CN99 DDNS
Server IP none
Server Port 80
Domain
Name
none
User none
Password N/A
DDNS
Update
Period
5 minutes
IP Filter
Trusted
sites
Disable
SMTP
Server
none
Port 25
Anonymity Disable
SMTP(Email)
User Name anonymity
Page 12
7
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
Password N/A
Sender none
Authenticati
on
(Encryption
mode)
N/A
Title
(Subject)
IPC Message
Attachment N/A
Mail
Receiver
0
seconds
Email Test Disable，interval=60 minutes
UPnP
Enable
UPnP
Disable
SNMP v1 Disable
SNMP v2 Disable
SNMP Port 161
Read
Community
public
Write
Community
private
Trap
Address
N/A
SNMP
Trap Port 162
Enable Enable
Bonjour
Server
Name
MAC
Multicast
Address
239.255.42.42
Multicast
Port 36666
Real-time
Monitor
0
QoS
Command 0
Enable Disable
Anti-dither 5 seconds
Sensitivity 3
Record
Channel
Enable
Record
Delay
10 seconds
Event
Video detect
Motion Detect
Relay out Enable
Page 13
8
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
Alarm Delay 10 seconds
Send Email Disable
Snapshot Disable
Enable Disable
Record
Channel
Enable
Record
Delay
10 seconds
Relay out Enable
Record
Delay
10 seconds
Send Email Disable
Video
Masking
Snapshot Disable
Enable Disable
Relay in Alarm 1
Anti-dither 0 seconds
Sensor
Type
NO
Record
Channel
Enable
Record
Delay
10 seconds
Relay out Enable
Alarm Delay 10 seconds
Send Email Disable
Alarm
Activation
Snapshot Disable
Alarm
Relay output 1
Enable Disable
Relay out Enable
Relay out
Delay
10 seconds
No SD Card
Send email Disable
Enable Disable
Capacity
Limit
10%
Relay out Enable
Relay out
Delay
10 seconds
Capacity
Warning
Send Email Disable
Enable Disable
Relay out Enable
Abnormity
SD Card
Error
Relay out
Delay
10 seconds
Page 14
9
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
Send email Disable
Enable Disable
Record Enable
Record
Delay
10 seconds
Relay out
Enable
Disconnectio
n
Relay out
Delay
10 seconds
Enable Disable
Record Enable
Record
Delay
10 seconds
Relay out Enable
IP Conflict
Relay out
Delay
10 seconds
Enable FTP Disable
Server IP N/A
Port 21
Username anonymity
Password N/A
Remote
path
share
Storage
FTP
Emergency
(Local)
Disable
Pack
Duration
8 minutes
Pre-record 5 seconds
Disk Full Overwrite
Record
Mode
Auto
Storage
Record Control
Record
Stream
Main stream
Device No Device MAC
Language English
Local Host
Video
Standard
PAL
Date Format Y-M-D
Time
Format
24H
Time Zone GMT+08:00
System
General
Date and
time
System
Time
Sync
Page 15
10
Default Setup
Setup Item
IPCHFW3300C
IPCHFW3200C
IPCHFW3100C
IPCHFW3101C
DST Disable
DST Type Week
Start Time 00:00:00 of the first Sunday of the month
End Time 00:00:00 of the second Monday of the month
NTP Disable
NTP Server clock.isc.org
Port 37
Update
Period
10 minutes
Auto Reboot Enable
Auto Maintenance
Auto Delete
Old Files
Disable
Page 16
11
2 Structure
2.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See Figure
2-1
.
Figure 2-1
Please refer to the following sheet for detailed information.
Port Name Function Connection Note
VIDEO OUT
Video output
port
BNC
Output analog video signal. It can connect to the
TV monitor to view the video.
AUDIO IN
Audio input
port
RCA
Input audio signal. It can receive the analog audio
signal from the pickup.
AUDIO OUT
Audio output
port
RCA
Output audio signal to the devices such as the
sound box.
DC 12V/AC 24V
Power input
port
/
Power port. Input DC 12V/AC 24V (Please use the
provided conversion cable)
I/O I/O port / Connect to I/O port.
LAN Network port
Ethernet
port
Connect to standard Ethernet cable.
Reset Reset port /
Hardware reset function. Press it for 3 to 5
seconds; system hardware can restore default
setup.
Please refer to the follow sheet for detailed I/O port information.
Page 17
12
Port Name SN Name Note
1 ALARM_COM Alarm output public port.
2 ALARM_NO
Alarm output port. It is to output the alarm signal
to the alarm device.
NO: normal open alarm output port.
It works with the ALARM_COM port.
3 ALARM_IN1
Alarm input port 1. It is to receive the on-off signal
from the external alarm source.
4 ALARM_IN2
Alarm input port 2. It is to receive the on-off signal
from the external alarm source.
I/O Port
5 GND Ground port
2.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.
Figure 2-2
Figure 2-3
Page 18
13
2.3 Bidirectional talk
2.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or the MIC to the audio input port of the device. Then connect the
earphone to the audio output port of the PC.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
2.3.2 PC-end to the Device-end
Device Connection
Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to
the audio output port of the device.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Please note the listening operation is null during the bidirectional talk process.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone
or sound box at the device-end.
2.4 Alarm Setup
The alarm interface is shown as in Figure 2-4. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public port
(No.1 pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2-4. Please set the alarm input 01 port for the first channel of the
I/O cable (No.3 pin). The alarm input 02 is for the 2
nd
channel of I/O cable (No.4 pin). Then you can
select the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.2 pin of the I/O cable.
Page 19
14
Figure 2-4
Please refer to the following figure for alarm input information. See Figure 2-5.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the
logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 2-5
Please refer to the following figure for alarm output information. See Figure 2-6.
Port NO and Port C composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes on when there is an alarm output.
If the type is NC, this button is normal off. The button becomes off when there is an alarm output.
Figure 2-6
Page 20
15
3 Device Installation
Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference.
z Please draw the installation holes in the installation surface and then mark three expansion
bolts holes in the surface. Insert three bolts in the hole and secure firmly.
z Please line up the installation holes of the bottom of the pendant mount bracket to the
installation holes in the surface. Then insert the three bolts to the holes of the bottom of the
bracket. Finally fasten the device on the installation surface.
Figure 3-1
Page 21
16
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Figure 4-2
Page 22
17
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure
4-3.
Figure 4-3
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.
Page 23
18
Figure 4-5
Page 24
19
5 Web Operation
This series IPC product support the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and
etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
z Make sure the IPC has connected to the network properly.
z Please set the IP address, subnet mask and gateway of the PC and the IPC respectively. IPC
default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.168.1.1
z Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.
5.2 Login and Logout
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 5-1.
Figure 5-1
The login interface is shown as below. See Figure 5-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here
Page 25
20
Figure 5-2
If it is your first time to login in, system pops up warning information to ask you whether install control
webrec.cab or not after you logged in for one minute. Please click OK button, system can
automatically install the control. When system is upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable
the control download. Or you can lower the IE security level. See Figure 5-3.
Figure 5-3
After you logged in, you can see the main window. See Figure 5-4.
Page 26
21
Figure 5-4
Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.
Page 27
22
6 FAQ
Bug
I can not boot up
the device.
Please click RESET button for at least five seconds to restore
factory default setup.
SD card write
times
Do not set the SD card as the storage media to storage the
schedule record file. It may damage the SD card duration.
I can not use the
disk as the storage
media.
When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).
I can not upgrade
the device via
network.
When network upgrade operation failed, you can use port 3800 to
continue upgrade.
Recommended SD
card brand
Kingston 4GB, Kingston 1GB, Kingston 16GB, Transcend 16GB,
SanDisk 1G, SanDisk 4G
Usually we recommend the 4GB (or higher) high speed card in case
the slow speed results in data loss.
Audio function Please use active device for the audio monitor input, otherwise there
is no audio in the client-end.
To guarantee
setup update
After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.
Power adapter The power adapter included in the accessories bag can work
ranging from 0℃ to 40 ℃. The device may result in unstable power
supply when the temperature exceeds the working temperature.
Please replace an industry-level power adapter if you are using in
the harsh environments.
I can not fix the
bracket firmly.
Please use the No.2 slot (150mm or higher) screwdriver to secure
the cross-head screws of the bracket firmly. Please use your hands
to test the camera is firm or not after the installation.
Page 28
23
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb Hg Cd Cr VI PBB PBDE
Circuit Board
Component
○ ○ ○ ○ ○ ○
Device
Construction
Material
○
○ ○ ○ ○ ○
Wire and Cable
○
○ ○ ○ ○ ○
Packing
Components
○ ○ ○ ○ ○ ○
Accessories ○ ○ ○ ○ ○ ○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes。
Note
z This user’s manual is for reference only. Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z All trademarks and registered trademarks are the properties of their respective owners.
z If there is any uncertainty or controversy, please refer to the final explanation of us.
z Please visit our website for more information.
Loading...