Dahua IPC-HFW2300R-Z Quick Start Manual

HD IR Vari-Focal Fixed Network Camera Quick Start Guide

Version 1.0.1

i

Welcome

Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please

note: Do not connect two power supplying sources to the device at the same time; it may result
in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.

ii

Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

1

Quick Start Guide

1

Installation Accessory Bag

1

CD

1

iii

Table of Contents

1 Framework ................................................................................................................................... 1

1.1 Device External Cable ................................................................................................. 1

1.2 Framework and Dimension ......................................................................................... 2

2 Device Installation ...................................................................................................................... 3

3 Quick Configuration Tool ........................................................................................................... 6

3.1 Overview ........................................................................................................................ 6

3.2 Operation ....................................................................................................................... 6

4 Web Operation ............................................................................................................................ 8

4.1 Network Connection ..................................................................................................... 8

4.2 Login and Main Interface ............................................................................................. 8

Appendix Toxic or Hazardous Materials or Elements ............................................................... 10

1

1 Framework

1.1 Device External Cable

You can refer to the following figure for device external cable information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

SN

Port

Port Name

Connection

Note

1

LAN

Network port

Ethernet
port

Connect to standard Ethernet cable.
Note:
Before making crystal head, pull the

anti-dust cover (default), waterproof
cover (optional) through network
cable.

2

DC 12V

Power input
port

-

Power port. Input DC 12V.