Dahua HAC-HFW Series User Manual

HDCVI IR Mini Fixed Camera User’s Manual

Version 1.0.0

2

Table of Contents

1 General Introduction .................................................................................................................. 1

1.1 Overview ........................................................................................................................ 1

1.2 Features ......................................................................................................................... 1

2 Device Framework ..................................................................................................................... 2

3 Installation.................................................................................................................................... 5

i

Welcome

Thank you for purchasing our HDCVI camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series HDCVI camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

7. Daily Maintenance

iii

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

iv

Applicable model

This manual can be applied to the following model:
HAC-HFW XXXXR HAC-HFW XXXXS HAC-HFW XXXXRM

1

1 General Introduction

1.1 Overview

This series HDCVI camera conforms to the HDCVI standard. It supports video signal high­speed long distance transmission without any delay. It can be controlled by the DVR
conforming to the HDCVI.

1.2 Features

 High-performance CMOS image sensor, megapixel definition.
 Support HD video, control signal coaxial transmission.
 720P series support 75-3 coaxial cable transmission without any loss. The distance is

over 500m.

 Support HDCVI HD output.
 High speed, long distance real-time transmission.
 Support DC12V power supplying.
 Support IP66 protection level.
 Support ICR switch to realize surveillance both in the daytime and at night.
 Support photosensor IR control function.
 Support max IR distance 20m. For HAC-HFW XXXXS, it supports IR distance 30m.
 Can be applied to the environments with darker light or no illumination like road,

warehouse, underground parking lot, bar, pipeline and etc.

2

2 Device Framework

Please refer to the following figures for dimension information. The unit is mm.

HAC-HFWXXXXR

Figure 2-1

Figure 2-2

HAC-HFWXXXXS

3

Figure 2-3

Figure 2-4

HAC-HFWXXXXRM

4

Figure 2-5

Figure 2-6

Figure 2-7

Figure 2-8

5

3 Installation

Important
 Before the installation, please make sure the installation surface can sustain at

least 3X weight of the bracket and the camera.

HAC-HFWXXXXR

Figure 3-1

Step 1

Install the camera bracket.
Please install the expansion bolt if you want to install in the cement wall (Please make sure the
installation holes of the expansion bolts are the same with the bracket.) Then you can install
the bracket. See Figure 3-1.
If you want to install in the wood surface, please skip the first step and then use the self­tapping screws to install the bracket directly.

Step 2

Install the camera. Use the screws to install the camera to the bracket via the installation
pedestal of the bottom of the camera.

Step 3

Adjust the camera to the proper monitor area and then secure the button of the bracket to
fasten the camera. See Figure 3-2.

6

Figure 3-2

HAC-HFWXXXXS

Step 1

Dig three holes in the installation surface of the wall or the ceiling. Insert three expansion bolts
to the three holes and then lock firmly. See figure 3-3.

7

Figure 3-3

Step 2

First prepare the cable according to the cable. Line up the three screw holes at the bottom of
the bracket to the three installation holes in the wall or the ceiling, and then insert three screws
to the three holes of the chassis of the bracket and fix them firmly. Now secure the bracket on
the installation surface of the wall or the ceiling.

Step 3

Adjust the camera to the proper monitor area via the three directions indicated in Figure 3-4
after you fixed the camera.

8

Figure 3-4

HAC-HFWXXXXRM

Figure 3-5

Step 1

 Please install the expansion bolt if you want to install in the cement wall (Please make

sure the installation holes of the expansion bolts are the same with the bracket.) Then you
can install the bracket. See Figure 3-5.

 If you want to install in the wood surface, please skip the first step and then use the self-

tapping screws to install the bracket directly.

Step 2

Unscrew the locking screws on the bracket in the direction shown in Figure 3-6, adjust the
camera to an exact location which needs to be monitored by rotating the bracket and camera
body, and then secure the bolts.

9

Figure 3-6

Step 3

Connect the video output port of the device cable to the terminal encode devices, and connect
the power port of the device cable to the power.

Note

 This manual is for reference only. Slight difference may be found in the user

interface.

 All the designs and software here are subject to change without prior written

notice.

 All trademarks and registered trademarks mentioned are the properties of their

respective owners.

 If there is any uncertainty or controversy, please refer to the final explanation of

us.

 Please visit our website or contact your local service engineer for more

information.