Dahua HAC-HF3101P/N User Manual

1 Megapixel ICR Day/Night WDR

Fixed HDCVI Camera User’s Manual

Version 1.0.0

i

Table of Contents

1 General Introduction ..................................................................................................................1

1.1 Overview........................................................................................................................1

1.2 Functions .......................................................................................................................1

1.3 Specifications................................................................................................................1

2 Framework...................................................................................................................................3

2.1 Rear Panel.....................................................................................................................3

2.2 Side panel......................................................................................................................4

2.3 Front Panel....................................................................................................................5

3 Installation ...................................................................................................................................6

3.1 Lens Installation............................................................................................................6

3.2 I/O Port Installation.......................................................................................................7

4 Menu.............................................................................................................................................8

Appendix Toxic or Hazardous Materials or Elements ...............................................................12

ii

Welcome

Thank you for purchasing our HDCVI camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual well for future reference!

iii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC or Ac 24V in the IEC60950-1.

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

If this product is installed in the ceiling, please make sure the installation position can sustain the min

50N.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series HDCVI camera should be installed in a cool, dry place away from direct sunlight or strong

light, inflammable, explosive substances and etc.

This series camera shall work on the specified working temperature. Please keep it away from the

electromagnetic radiation object and environment.

Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it

may result in CMOS optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

7. Daily Maintenance

iv

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the

mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.

Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1

1 General Introduction

1.1 Overview

This series megapixel HD camera conforms to the HDCVI standard. It supports video signal

high-speed long distance transmission without any delay. The HDCVI port adopts coaxial

cable and uses BNC port as the standard cable.

This series product has megapixel definition. It supports DC 12V/AC 24V power supplying. It

supports HDCVI HD and CVBS standard definition output, and OSD operation.

1.2 Functions

Data Transmission

It adopts coaxial cable and use BNC port as the standard cable specifications.

Peripheral Device Control

It can be controlled by the DVR conforming to the HDCVI specifications via the video coaxial

cable

Power Supplying

Support external power adapter supplying. Support AC 24V/DC 12V.

Aux Function

z Auto day/night switch (With ICR switch)

z The WDR can max reach 120dB, suitable for the backlight environments.

z Support video/audio/control signal transmission over the same coaxial cable.

z General 75-3 coaxial cable supports over 500m transmission distance without any quality

loss.

z Support 1280*720@25fps, 1280*720@30fps

z 3D NR function

z Support privacy mask function.

z Support auto iris function.

z Support OSD operation.

z HDCVI HD/standard definition output switch function.

1.3 Specifications

Please refer to the following sheet for specification.

1 Megapixel ICR Day/Nigh WDR Fixed HDCVI Camera Model

Parameter

HAC-HF3101P/N

Video
Processor

1/3" 1.3 Megapixels CMOS

Video

Video Format PAL/NTSC

2

Sensor Pixel 1280(H)×960(V)
Min

Illumination

Color: 0.01Lux@（F1.2,AGC ON）,
Black and white: 0.001Lux@（F1.2,AGC ON）,

Electronic
Shutter

1/1s～1/10000s@ (slow shutter*512）

Video Standard

HDCVI/CVBS compliance

Video Frame
Rate

1280*720@25fps ;1280*720@30fps

Day/Night
Switch

ICR mechanical auto switch

Lens Port

C/CS

Auto Iris

DC Drive

WDR Range

120dB

Audio/Video
Transmission

Support audio/video transmission over the same coaxial cable.

Control Signal
Transmission

Support OSD control and video transmission over the same coaxial cable.

SCENE INDOOR/OUTDOOR/WDR
EXPOSURE AUTO/AUTO IRIS/AUTO SHUTTER/MANUAL

FUNCTION WB/WDR/NR/MIRROR/DAY&NIGHT/HLC/BLC
IMAGE

MODE/HUE CNT/SHARPNESS/SHARP
CNT/BRIGHTNESS/SATURATION/HUE/GAMMA

ADVANCED

MOTION DETECT/PRIVACY MASK/FREEZE/ALARM MODE/RS­485/CAMERA ID/LANGUAGE/SYSTEM INFO

OSD

EXIT INDOOR/RESTART/FORMAT/BACK
Video Output 1-channel BNC HDCVI HD/CVBS standard definition output (Can switch)

Audio Input

1-channel audio input port. Connect to devices such as pick up.

Standard
Definition/HD
Switch

Hardware button. Press for 5 seconds to switch standard definition/HD
definition mode.

ICR External
Trigger

External trigger signal to activate day/night mode switch.

Alarm Output 1-channel on-off signal output. Can activate motion alarm.

AUX
Port

RS485 port

Support OSD operation. Software online upgrade.

Power
Supplying

AC 24V/DC 12V

Power
Consumption

7W Max (Input:12V 0.58A/24V～0.52A)

Working
Temperature
/Humidity

-30℃~+60℃. Humidity is less than 95%(no condensation)

Dimension(mm)

70×63.2×136.5

Weight

650g

General

Installation
Mode

Support various installation modes (Housing and bracket is optional)

3

2 Framework

2.1 Rear Panel

Please refer to the following figure for the rear panel information. See Figure 2-1.

Figure 2-1

Port Name Connector Port Function

AC 24V/ DC

12V

Power port

z Power port.

z Connect to AC 24V/ DC 12V.

Red light

Power light. The light is on after system boots
up.

Green light

Hardware indicator light. The light becomes
on after system successfully loads the
hardware part.

Indicator
light

Yellow light

HD/standard definition indicator light. The
light is off when system is using the HD
output. The light is on when system is using
standard definition.

IN

ICR external
trigger

Connect to external on-off output to control
ICR switch to realize day/night mode switch.

Please note: if you want to use this function,

you need to go to the OSD menu to set the
day/night mode as EXT TRIG-HIGH or EXT
TRIG-LOW. The control signal shall connect
to the IN and G port. For example, connect
the 5V to the IN port and the day/night mode
as EXT TRIG-HIGH , the camera can switch
from day mode to night mode.

NO Alarm normal open

contact

On-off signal alarm output.

C Alarm output public

contact

On-off signal alarm output.

4

Port Name Connector Port Function

G

GND Ground end.

A RS485_A port. Connect to DVR or RS485

configuration tool to set video parameters.

B

RS485 port

RS485_B port. Connect to DVR or RS485
configuration tool to set video parameters.

NA

N/A Reserved

RX

TX

G

Reserved port

For R/D use only.

RESET Reset button

Press it for five seconds, system can reload

again and restore factory default setup.

HDCVI

Video/audio/control
composite port

Send video stream/audio stream/control data
stream conforming to HDCVI specifications.
Please connect to the HDCVI DVR series
product to control.

MIC IN

Microphone audio
input

Audio input from the pickup.

5-direction
button

OSD button

z Press the middle button for five

seconds to switch HD/standard
definition mode.

z Press the middle button shortly to go to

the OSD menu interface.

z After you go to the menu, click the

middle button to confirm current
operation. Move the up/down button to
select menu item and use left/right
button to set parameter value.

GND port

Before you use this series product, please
make sure it has been soundly grounded in
case there is a risk of thunder strike.

2.2 Side panel

Please refer to the following figure for the rear panel information. The unit is mm. See Figure

2-2.

5

Figure 2-2

2.3 Front Panel

Please refer to the following figure for the front panel information. The unit is mm. See Figure

2-3.

Figure 2-3

6

3 Installation

Important
z Before the installation, please make sure the installation surface can sustain at

least 3X weight of the bracket and the camera.

3.1 Lens Installation

Please refer to the steps listed below for installation information. See Figure 3-1 and Figure 3-2.

z Remove the protection cap from the device. Line up the lens to the lens position of the

camera (Install the C/CS adapter ring to the camera if you are using C type lens).Turn

clockwise to secure the lens firmly.

z Insert the socket of the lens cable to the auto iris lens connector on the side panel of the

device. Skip this step if you are using auto iris lens.

z Fasten the screw near the focusing ring and then turn counter clockwise to move the

focusing ring out for several millimeters. Now you can focus manually until you get clear

video.

z After you completed the focus setup, fix the screw near the focusing ring firmly. Fasten the

focusing ring. Now the installation is complete.

Figure 3-1

7

Figure 3-2

3.2 I/O Port Installation

Install Cable

Please follow the steps listed below to install the cable. See Figure 3-3.

Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the

cable into the groove and then release the screwdriver.

Remove Cable

Please follow the steps listed below to remove the cable.

Use the small slotted screwdriver to press the corresponding button of cable groove. Remove

the cable out of the groove and then release the screwdriver.

Figure 3-3

8

4 Menu

Important
Please check the current video output mode when there is no video output. The yellow
light is on when system is outputting standard definition video. The yellow light is off
when system is using high definition video.

THE 1ST MENU THE 2ND MENU THE 3RD MENU

SCENE
INDOOR
SCENE
OUTDOOR
SCENE WDR

SCENE

BACK

MAX SPEED
MIN SPEED

PAL:

1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000

NTSC:

1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1
/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.

SLOW SHUTTER PAL:

1/1,1/2,1/3,1/6,1/12,1/25,1/50,1/7
5,1/100,1/120

NTSC:

1/1, 1/2, 1/4, 1/8, 1/15, 1/30,1/60,
1/90,1/100,1/125

SHUTTER
AUTO…

BACK

GAIN

-1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）

LENS---

It is read-only on auto mode.
EC OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1

00

AUTO

BACK

SHUTTER PAL:

1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,

1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,

1/10000

NTSC:

1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/

1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN

-1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）

LENS It is read-only on auto iris mode.
EC OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1

00

IRIS

BACK

MAX SPEED

EXPOSURE

SHUTTER SHUTTER

AUTO…

MIN SPEED

PAL:

1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000

NTSC:

1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1

9

/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.

SLOW SHUTTER PAL:

1/1,1/2,1/3,1/6,1/12,1/25,1/50,1/7
5,1/100,1/120

NTSC:

1/1, 1/2, 1/4, 1/8, 1/15, 1/30,1/60,
1/90,1/100,1/125

BACK
GAIN

-1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）

LENS It is read-only on auto shutter mode.
EC OFF,+0,+1.+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1

00
BACK

SHUTTER PAL:

1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,

1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,

1/10000

NTSC:

1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/

1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN

-1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）

LENS MODE OPEN, MODE

OFF
EC It is read-only on manual mode.
LLC It is read-only on manual mode.

MANUAL

BACK
AUTO
INDOOR
OUTDOOR
ONE PUSH
ATW

RED GAIN 000-255 MANUAL…

BLUE GAIN 000-255
OUTDOOR
AUTO
SODIUM
AUTO

WB

SODIUM
OFF

INTENSITY 1-5

MOTION COMP

WDR

ON…

RETURN
2D-NR OFF, 1-5
3D-NR OFF, 1-5

NR…

BACK

MIRROR OFF, V-FLI,H-FLIP, CENTRE

SWITCH POINT 1-7

TOLERANCE 1-6

DAYÆNIGHT 2S-30S

NIGHT ÆDAY 2S-30S

AUTO …

BACK
DAY
NIGHT
EXT TRIG­HIGH

FUNCTION

D/N

EXT TRIG-

10

LOW

HLC OFF, 1, 2
BLC OFF,1, 2
BACK
MODE CUSTOM , FLAMBOYANT,SOFT,

Note: For non-custom mode, the rest parameters are read-only.

HUE CNT 00~15
SHARPNESS 00~15
SHARP CNT 00~15
BRIGHT 000~255
SATURATION 000~255
HUE 000~255
GAMMA 00~15

IMAGE

BACK

SN 1-4
ON/OFF ON/OFF
DISPLAY ON/OFF
SENSITIVIT
Y

00~99

LC

（0-23,0-15）

AREA
LOCATION
…

SZ

（0-23,0-15）

MOTION
DETECT…

BACK
INDEX 0-7
N/F ON/OFF
CENTRE
SET…
SIZE SET…
COLOR BLUE

PRIVACY
MASK …

BACK

FREEZE ON,OFF

TYPE MOTION DETECT
MODE ON/OFF

ALARM
MODE…

INTERVAL

CLOSE，1S-255S

NEXT…

Support PELCO-D/P, DH-SD protocol.
BAUD RATE 1200-9600
ADDRESS 001-254

RS-485…

BACK
OFF
ON… CAMERA ID 1-254

CAMERA ID

BACK

LANGUAGE ENGLISH

MANUFACT
URER

xxx

HARDWARE XXX
SOFTWARE XXX

SYSTEM
INFO…

BACK

PREVIOUS …

ADVANCED

BACK

INDOOR CANCEL,

SAVE ，
DEFAULT ，
RESET

RESTART…

EXIT

FORMAT

720@25… ，

11

720@30…

BACK

12

Appendix Toxic or Hazardous Materials or Elements

Toxic or Hazardous Materials or Elements

Component

Name

Pb Hg Cd Cr VI PBB PBDE

Circuit Board

Component

○ ○ ○ ○ ○ ○

Device

Construction

Material

○

○ ○ ○ ○ ○

Wire and Cable

○

○ ○ ○ ○ ○

Packing

Components

○ ○ ○ ○ ○ ○

Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials

in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all

homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006

standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous

substance or elements contained in products will not leak or mutate so that the use of these

(substances or elements) will not result in any severe environmental pollution, any bodily injury

or damage to any assets. The consumer is not authorized to process such kind of substances

or elements, please return to the corresponding local authorities to process according to your

local government statutes.

Note

• This manual is for reference only. Slight difference may be found in the user
interface.

• All the designs and software here are subject to change without prior written
notice.

• All trademarks and registered trademarks mentioned are the properties of their
respective owners.

• If there is any uncertainty or controversy, please refer to the final explanation of
us.

• Please visit our website or contact your local service engineer for more
information.