Dahua HAC-HDW1100RP-VF User Manual

Page 1
1 Megapixel HDCVI IR Vari-focal Dome Camera
User’s Manual
Version 1. 0.0
Page 2
Table of Contents
1 General Introduction ........................................................... Błąd! Nie zdefiniowano zakładki.
1.1 Overview ................................................................. Błąd! Nie zdefiniowano zakładki.
1.2 Features .................................................................. Błąd! Nie zdefiniowano zakładki.
1.3 Functions ................................................................ Błąd! Nie zdefiniowano zakładki.
1.4 Specifications ......................................................... Błąd! Nie zdefiniowano zakładki.
2 Framework and Dimensions ..................................................................................................... 1
2.1 Dimensions ............................................................. Błąd! Nie zdefiniowano zakładki.
2.2 Structure ................................................................. Błąd! Nie zdefiniowano zakładki.
3 Installation.................................................................................................................................... 5
4 Menu ............................................................................................................................................. 6
4.1 Menu List ................................................................ Błąd! Nie zdefiniowano zakładki.
4.2 Note ......................................................................... Błąd! Nie zdefiniowano zakładki.
Appendix Toxic or Hazardous Materials or Elements ................................................................. 7
Delta-Opti, 2015
Page 3
ii
Welcome
Thank you for purchasing our HDCVI camera! This users manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this users manual well for future reference!
Page 4
iii
Important Safeguards and Warnings
1Electrical safety
All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC 24V AC)in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
2Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
3Installation
Do not apply power to the camera before completing installation. Please install the proper power cut-off device during the installation connection. Always follow the instruction guide the manufacturer recommended. If this product is installed in the ceiling, please make sure the installation position can sustain the min 50N.
4Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.
5Environment
This series analog camera should be installed in a cool, dry place away from direct sunlight or strong light, inflammable, explosive substances and etc. This series camera shall work on the specified working temperature. Please keep it away from the electromagnetic radiation object and environment. Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it may result in CMOS optical component damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance
Page 5
iv
Please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CMOS component when you do not use the camera.
Page 6
1
1 General Introduction
1.1 Overview
This series megapixel HD camera conforms to the HDCVI standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the DVR conforming to the HDCVI.
1.2 Features
High-performance CMOS image sensor, megapixel definition. Support HDCVI video output. Support 75-3 coaxial cable transmission without any loss. Transmission distance is over
500m.
High speed, long distance real-time transmission. Support ICR switch to realize surveillance both in the daytime and at night. Support auto exposure, auto white balance, auto electronic shutter and auto gain function.
High image color rendition, vivid image. Support manual adjustment of lens zoom and focus, conduct lens focus and zoom by
adjusting the focusing nut on the upper part of the dome body, which is convenient for users to install.
Support DC12V power supplying. Support IP66 compliance. Support intelligent IR function, max IR distance 30m.
1.3 Functions
HDCVI Specification
HDCVIHigh Definition Composite Video Interface is an over-coaxial –cable HD video transmission standard. The technology renders two HD video formats by progressive scanning.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general fitter at night. This function allows the camera to output the high sensitivity and clear video.
Smart IR technology
The sensor controls the IR light on/off via the combination work of the hardware and software, which realizes the automatically IR light compensation according to the environment illumination.
Auto gain function
To output the standard video signal in the different illumination environments, the amplifier needs to adjust in a wide range. The system can enhance the camera sensitivity in low illumination and enhance the video signal output to get the clear and high definition video.
Auto white balance
Page 7
2
The white balance refers to the camera to restore the white object color. It allows the camera to automatically adjust the color temperature in indoor and outdoor environment, just like our human eyes does.
Auto exposure
System can automatically set shutter speed and iris value according to the snapshot video exposure condition.
Auto electronic shutter
The system can automatically adjust the electronic shutter when the environment light changes.
1.4 Specifications
Model Parameter
1 Megapixel HDCVI IR Vari-focal Dome Camera Series
HAC-HDW1100RP/N-VF
Video Processor
1/2.9" 1.0 Mega Pixels CMOS
Video Format
PAL/NTSC
Effective Pixel
1280(H)* 720(V)
Min Illumination
0.01Lux @F1.2,AGC ON),0Lux with IR
Electronic Shutter
PAL1/50s~1/100,000s NTSC1/60s~1/100,000s
Video Standard
HDCVI compliance
Video Frame Rate
PAL1280×720@25 fps NTSC1280×720@30 fps
Lens Port
Φ14
Lens Type
2.7-12 mm @F1.4 fixed iris manual vari-focal lens
Day/Night Switch
ICR auto switch
Sync Mode
INT
Video Output
1-channel HDCVI high definition video output
White Balance
Auto
Gain Control
Auto
BLC
Auto
Smart IR
Support
Transmission Distance
Over 500m via 75-3 coaxial cable without any loss
Max IR Distance
30m
Protection Level
IP66
Working Temperature /Humidity
-30~+60. Humidity is less than 95%(no condensation)
Power
DC 12V±10%
Power Consumption
2.8 W MAX(Input: 12V 0.23A)
Page 8
3
Dimension(mm)
Φ119×97.4
Weight
550g
Angle Adjustment
Pan: 0°~360°: Tilt: 0°~73°: Flip: 0°~360°
Installation Mode
Wall mount/In-ceiling mount
Page 9
4
2 Framework and Dimensions
Please refer to the following figures for dimension information. The unit is mm. See Figure 2-1 and Figure 2-2.
Figure 2-1
Figure 2-2
Page 10
5
3 Installation
Important Before the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
Figure 3-1
Step1 Take the installation position map from the accessories bag, and stick it on the ceiling or wall according to the cable exit, dig four holes according to the instruction on the installation position map, then take out four expansion bolts from accessories bag and put them into the installation holes and fix them. Step 2 Open decoration ring and take down enclosure and dome body Step 3 Adjust the pedestal position according to the cable exit mode (ceiling/side), Pull the cable through the cable side exit at the installation surface and the pedestal (Please skip this step if you want to use ceiling exit mode). Line up the screw holes at the bottom of the pedestal to the holes of plastic expansion bolts in the installation surface. Put four self-tapping screws to expansion bolts and then secure firmly, and fix the pedestal on the installation surface, see
Page 11
6
Figure 3-1 for the details. Step 4 Aim the decoration ring together with enclosure and dome body up to the pedestal, pull the cable through the cable exit on the installation surface (Please skip this step if you want to use side exit mode), screw the decoration ring and fix the enclosure and dome body on the pedestal. Adjust the camera to an appropriate angle for monitoring according to the direction which is shown in Figure 3-1. Step 5 Connect the video output port of the device cable to the back-end encoding device, and connect the power port of the device to power supply. Step 6 After the image is displayed on the back-end encoding device, adjust the focusing nut which is inside of zoom adjustment hole and focus adjustment hole by focusing tool to make the image clear.
Now you have completed the device installation and cable connection. You can use the terminal encode device to view the monitor video.
Page 12
7
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board
Component
○ ○ ○ ○ ○
Device
Construction
Material
Wire and Cable
Packing
Components
○ ○ ○ ○ ○
Accessories
○ ○ ○ ○ ○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized to process such kind of substances or elements, please return to the corresponding local authorities to process according to your local government statutes.
Note
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local service engineer for more
information.
Loading...