Dahua DH-IPC-HFW3200S User Manual

bezpeka-shop.com

HD IR Waterproof Fixed Network Camera User’s Manual

Version 1.2.0

Zhejiang Dahua Technology CO.,LTD

i

bezpeka-shop.com

Welcome

Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii

bezpeka-shop.com

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please

note: Do not connect two power supplying sources to the device at the same time; it may result
in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii

Accessory Name

Amount

Network Camera Unit

1

Quick Start Guide

1

Installation Accessories Bag

1

CD

1

Warranty Card and Certificate

1

bezpeka-shop.com

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

iv

bezpeka-shop.com

Table of Contents

1 General Introduction .............................................................................................................. 1

1.1 Overview ................................................................................................................... 1

1.2 Features ................................................................ .................................................... 1

1.3 Specifications ........................................................................................................... 2

1.3.1 Performance ...................................................................................................... 2

2 Structure ................................................................................................................................. 6

2.1 Multiple-function Combination Cable ..................................................................... 6

2.2 Framework and Dimension ..................................................................................... 6

3 Device Installation ................................................................................................................. 8

4 Quick Configuration Tool .................................................................................................... 10

4.1 Overview ................................................................................................................. 10

4.2 Operation ................................ ................................................................................ 10

5 Web Operation ..................................................................................................................... 12

5.1 Network Connection............................................................................................... 12

5.2 Login and Main Interface ....................................................................................... 12

6 FAQ ....................................................................................................................................... 15

Appendix Toxic or Hazardous Materials or Elements ............................................................. 16

1

User

Management

 Different user rights for each group, one user belongs to one group.
 The user right shall not exceed the group right.

Storage

Function

 Support central server backup function in accordance with your configuration

and setup in alarm or schedule setting

 Support record via Web and the recorded file are storage in the client-end

PC.

 Support network storage function such as FTP.

Data

Transmission

 Data transmission via PoE.

Network

Monitor

 It supports one-channel video data transmit to network terminal and then

decode. Delaying time is within 270ms (network bandwidth support needed)

 Max supports 20 connections and output bandwidth is 32Mbps. System

refuses new connection request once it exceeds the bandwidth threshold.

 Adopt the following video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

 Support web access.

Network

Management

 Realize network camera configuration and management via Ethernet.
 Support device management via web or client-end.
 Support various protocols.

Power

 External power adapter DC 12V.
 Support PoE. (Please refer to specifications.)

Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!

Assistant

Function

 Log function
 Support system resource information and running status real-time display.
 Day/Night mode auto switch.
 Support picture parameter setup such as electronic shutter and gain setup.
 Backlight compensation: screen auto split to realize backlight compensation

to adjust the bright.

 Support digital WDR.

bezpeka-shop.com

1 General Introduction

1.1 Overview

This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.

This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for
use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.

1.2 Features

2

 Support video watermark function to avoid vicious video modification.
 Support dual bit streams, ACF.

Model
Parameter

IPC-HFW3200SP/N Series

IPC-HFW2100S

System

Main Processor

TI Davinci high performance DSP

OS

Embedded LINUX

System
Resources

Support real-time network, local record, and remote operation at the
same time.

User Interface

Remote operation interface such as WEB, DSS, PSS

System Status

Bit stream statistics, log, and software version.

Video Parameter

Image Sensor

1/2.8" CMOS

1/3 " CMOS

Pixel

1920(H)*1080(V)

1280 (H)*960 (V)

Day/Night Mode

Support day/night switch

Gain Control

Fixed/Auto

White Balance

Manual/Auto

BLC

On/Off

Exposure Mode

Manual/Auto
It ranges from 1/3 to 1/10000

Video
Compression
Standard

H264/ H.264B/H.264H/MJPEG
Note: Some versions may not support H.264H.

Video Frame
Rate

PAL:
Main
stream(1920*1080@25fps)，
extra stream (704*576@25fps)
NTSC:
Main
stream(1920*1080@30fps)，
extra stream(704*480@30fps)

PAL:
Main stream(1280*960@15fps)，
extra stream (704*576@15fps)
Main stream(1280*720@25fps)，
extra stream (704*576@25fps)

NTSC:
Main stream(1280*960@15fps)，
extra stream(704*480@15fps)
Main stream(1280*720@30fps)，
extra stream(704*480@30fps)

Video Bit Rate

H.264: 56Kbps-8192Kbps.
MJPEG is adjustable and bit rate
is adjustable.
Support customized setup.

H.264: 56Kbps-6144Kbps.
MJPEG is adjustable and bit rate
is adjustable.
Support customized setup.

Video Flip

Support mirror.
Support flip function.

Snapshot

Max 1f/s snapshot. File extension name is JPEG.

Privacy Mask

Supports max 4 privacy mask zones

Video Setup

Support parameter setup such as bright, contrast.

Video
Information

Channel title, time title, motion detect, camera masking.

Lens

3.6mm, 6mm, 8mm. Fixed focus.

Lens Interface

M12. Lens is the default accessories

bezpeka-shop.com

1.3 Specifications

1.3.1 Performance

Please refer to the following sheet for network camera performance specification.

3

Video

Motion Detect

396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The
6th level has the highest sensitivity)
Activation event: video storage, image snapshot, log, email function
and etc.

Record

and

Backup

Storage
Management

Support display local storage status

Network

Wire Network

1- channel wire Ethernet port, 10/100 Base-T Ethernet

Network Protocol

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.

Remote
Operation

Monitor, system setup, file download, log information, maintenance ,
upgrade and etc

Restore Default
Setup

Reset button (on LED panel)

IR light

IR light 20-30M.

General Parameter

Power

DC 12V power and PoE.

Power
Consumption

DC 12V

6.5 W MAX

DC 12V
6W MAX

Working
Temperature

-20℃~+60℃

Working
Humidify

≤95%

Dimensions(mm)

70*66*160

Weight

0.5Kg（Excluding box）

Installation

Bracket installation

Model
Parameter

IPC-HFW4100S

IPC-HFW4200S

IPC-HFW4300S

System

Main Processor

High performance DSP

OS

Embedded LINUX

System
Resources

Support real-time network, local record, and remote operation at the
same time.

User Interface

Remote operation interface such as WEB, DSS, PSS

System Status

Bit stream statistics, log, and software version.

Video Parameter

Image Sensor

1/3 " CMOS

1/2.8" CMOS

1/3 " CMOS

Pixel

1280(H) ×960(V)

1920(H) ×1080(V)

2048(H) ×1536(V)

Day/Night Mode

Support day/night switch

Gain Control

Fixed/Auto

White Balance

Manual/Auto

BLC

On/Off

Exposure Mode

Auto/Low noise/Low motion blur/Manual
It ranges from 1/3 to 1/100000.

Video
Compression
Standard

H264/H.264H/MJPEG

bezpeka-shop.com

4

Video Frame
Rate

PAL:
Main
stream(1280*960@25
fps)，
extra stream
(704*576@25fps)
NTSC:
Main
stream(1280*960@30
fps)，
extra
stream(704*480@30f
ps)

PAL:
Main
stream(1920*1080@2
5fps)，
extra stream
(704*576@25fps)
NTSC:
Main
stream(1920*1080@3
0fps)，
extra
stream(704*480@30f
ps)

PAL:
Main
stream(2048*1536@2
0fps)，
extra stream
(704*576@20fps)
Main
stream(1920*1080@2
5fps)，
extra stream
(704*576@25fps)

NTSC:
Main
stream(2048*1536@2
0fps)，
extra
stream(704*480@20f
ps)

Video Bit Rate

H.264: 16Kbps-8192Kbps.
MJPEG is adjustable and bit rate is adjustable.
Support customized setup.

Video Flip

Support mirror.
Support flip function.

Snapshot

Max 1f/s snapshot. File extension name is JPEG.

Privacy Mask

Supports max 4 privacy mask zones

Video Setup

Support parameter setup such as bright, contrast.

Video
Information

Channel title, time title, motion detect, camera masking.

Lens

3.6mm, 6mm, 8mm. Fixed focus.

Lens Interface

M12. Lens is the default accessories

Video

Motion Detect

396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The
6th level has the highest sensitivity)
Activation event: video storage, image snapshot, log, email function
and etc.

Record and

Backup

Record Priority

Manual>video detect>schedule

Storage
Management

Support display local storage status

Network

Wire Network

1-channel wire Ethernet port, 10/100 Base-T Ethernet

Network Protocol

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.

Remote
Operation

Monitor, system setup, file download, log information, maintenance ,
upgrade and etc

Restore Default
Setup

Reset button

IR light

IR light 20-30M.

Gene

ral

Para

mete

Power

DC 12V power and PoE.

Power
Consumption

DC 12V
5 W MAX

DC 12V

5.5 W MAX

bezpeka-shop.com

5

Working
Temperature

-20℃~+60℃

Working
Humidify

≤95%

Dimensions(mm)

70*66*160

Weight

500g（Excluding box）

Installation

Bracket installation

bezpeka-shop.com

6

SN

Port Name

Function

Connection

Note

1.

LAN

Network port

Ethernet
port

Connect to standard Ethernet cable.

2

DC12V

Power input
port

/

Power input port. Input DC 12V.

bezpeka-shop.com

2 Structure

2.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See Figure
2-1.

Figure 2-1 Multiple-function combination cable

Please refer to the following sheet for detailed information.

2.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.

7

bezpeka-shop.com

Figure 2-2 Dimension illustration 1

Figure 2-3 Dimension illustration 2

8

bezpeka-shop.com

3 Device Installation

Important
The installation wall shall min sustain 3X weight of the bracket and camera.

Please follow the steps listed below to install the device. Please refer to Figure 3-1 and Figure 3-2 for
reference.

Step 1

Paste the installation map on the surface of the wall or the ceiling.

Step 2

Dig the installation holes according to the installation map.

Figure 3-1 Device installation 1

Step 3

Open the accessories bag and then take the expansion bolt out. Insert the expansion bolt into the
installation holes.

Step 4

Take the screws from the accessories bag and then use them to secure the device on the installation
surface of the wall or the ceiling. The sun shield of the device can move forward or backward. Please
secure the set screw of the sun shield after you fixed the device.

Step 5

Connect the corresponding cables.

Step 6

Use the cross-head screwdriver to loosen the adjust screw.

Step 7

Turn the device in different directions to make it suitable for the monitor position.

Step 8

Use the cross-head screwdriver to fix the adjust screw firmly.

9

bezpeka-shop.com

Figure 3-2 Device installation 2

10

bezpeka-shop.com

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.

Figure 4-1 Search interface

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 4-2 Search interface 2

If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.

11

bezpeka-shop.com

In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 4-3 Login prompt

After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.

Figure 4-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

12

Input your IP
address here

bezpeka-shop.com

5 Web Operation

This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.

 Make sure the network camera has connected to the network properly.
 Please set the IP address, subnet mask and gateway of the PC and the network camera

respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1

 Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Main Interface

Open IE and input network camera address in the address bar. See Figure 5- 1.

Figure 5- 1 IP address

The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.

Note: For security reasons, please modify your password after you first login.

13

bezpeka-shop.com

Figure 5- 2 Web login

If it is your first time to log in, system pops up warning information to ask you whether install web plug­in or not after you logged in for one minute. For detailed plug-in installation, please refer to the Web
Operation Manual included in the resource CD.
After you logged in, you can see the main window. See Figure 5- 3.

Figure 5- 3 Web monitoring window

14

bezpeka-shop.com

Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.

15

Bug

I can not boot up
the device or
operate properly.

Please click RESET button for at least five seconds to restore
factory default setup.

The water leakage
occurred.

The unauthorized front or rear cap remove many result in water
leakage.

The glass front cap has sustained heavy push or strike.
The waterproof plug of the rear cap becomes loosen.

IR video is poor.

Do not use the proper supplying power. The IR light can not turn on
completely.

The object is out of the IR distance range of current device.
IR-CUT does not turn to the night mode. The photosensitive chip of

the front-end can not sense the IR light.

I can not upgrade
the device via
network.

When network upgrade operation failed, you can use port 3800 to
continue upgrade.

I can not login the
client-end or the
WEB.

 For Windows OS 98 or Windows ME user, if you can not install

the client-end or can not view after the installation. We
recommend the win2000sp4 OS or install the client-end of the
low version.

 The Active X control is blocked.
 The display card version shall be dx8.1 or higher.
 Network connection error occurred.
 Invalid network setup.
 Invalid user name or password.

I can not play the
download file.

 There is no player.
 There is no DX8.1 or higher.
 For the MEDIA PLAYER, there shall be Div X503Bundle.exe

plugin if you play the .AVI file.

 For Windows XP user, you need to install the plugin

DivX503Bundle.exe and ffdsho-2004 1012.exe.

To guarantee
setup update

After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.

Power adapter

 The general power adapter can work ranging from 0℃ to 40 ℃.

The device may result in unstable power supply when the
temperature exceeds the working temperature.

 Please replace an industry-level power adapter if you are using

in the harsh environments.

bezpeka-shop.com

6 FAQ

16

Component

Name

Toxic or Hazardous Materials or Elements

Pb

Hg

Cd

Cr VI

PBB

PBDE

Circuit Board

Component

○ ○ ○ ○ ○

○

Device Case

○ ○ ○ ○ ○ ○

Wire and Cable

○ ○ ○ ○ ○ ○

Packing

Components

○ ○ ○ ○ ○

○

Accessories

○ ○ ○ ○ ○

○

bezpeka-shop.com

Appendix Toxic or Hazardous Materials or Elements

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.

Note

 This user’s manual is for reference only. Slight difference may be found in user interface.
 All the designs and software here are subject to change without prior written notice.
 All trademarks and registered trademarks mentioned are the properties of their respective

owners.

 If there is any uncertainty or controversy, please refer to the final explanation of us.
 Please visit our website for more information.

Dahua Technology Co.,Ltd

Address：No.1187 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[e-mail]
Website: www.dahuatech.com