bezpeka-shop.com
Cost-effective HD Indoor Network Camera User’s Manual
Version 4.0.0
Zhejiang Dahua Technology CO.,LTD
i
Welcome
bezpeka-shop.com
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
ii
Important Safeguards and Warnings
bezpeka-shop.com
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please
note: Do not connect two power supplying sources to the device at the same time; it may result
in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
Accessory Name
Amount
Network Camera Unit
1
CS/C Adapter Ring
1
Quick Start Guide
1
CD
1
bezpeka-shop.com
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
iv
Table of Contents
bezpeka-shop.com
1 General Introduction .................................................................................................................. 1
1.1 Overview ........................................................................................................................ 1
1.2 Features ......................................................................................................................... 1
1.3 Specifications ................................................................................................................ 2
1.3.1 Performance ........................................................................................................... 2
1.3.2 Factory Default Setup ........................................................................................... 3
2 Structure ...................................................................................................................................... 9
2.1 Rear Panel ..................................................................................................................... 9
2.2 Framework and Dimension ....................................................................................... 10
3 Device Installation .................................................................................................................... 11
4 Quick Configuration Tool ......................................................................................................... 13
4.1 Overview ...................................................................................................................... 13
4.2 Operation ..................................................................................................................... 13
5 Web Operation .......................................................................................................................... 15
5.1 Network Connection ................................................................................................... 15
5.2 Login and Main Interface ........................................................................................... 15
6 FAQ ............................................................................................................................................ 18
Appendix Toxic or Hazardous Materials or Elements ............................................................... 19
1
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support network storage function such as FTP.
Network
Monitor
Network camera supports one-channel video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections. Max support 24Mbps output band width. The
new query may fail if it has reached the threshold.
Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Power
External power adapter DC12V.
Support PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Support system resource information and running status real-time display.
Day/Night mode auto switch.
Support picture parameter setup such as electronic shutter and gain setup.
Support motion detect function.
Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.
Support video watermark function to avoid vicious video modification.
bezpeka-shop.com
1 General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.
This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.
This series network camera has megapixel definition. It supports DC 12V power supplying, watermark
function and etc.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Comparing with the products of the same cost, it realizes
the high definition standard. And due to its multiple functions and various uses, this series network
camera is widely used in many indoor environments and the places of the monitor requirements.
1.2 Features
2
Model
Parameter
IPC-HF2100 Series
System
Main Processor
TI Davinci high performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
Pixel
1280(H)*960(V)
Day/Night Mode
Support day/night mode switch.
Auto Iris
On
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
Off/BLC/WDR (1-100 adjustable) /HLC (anti-flicker is outdoor which is
1-100 adjustable only when exposure mode set to auto.)
Exposure Mode
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Video
Compression
Standard
H.264/H.264H/H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream(1280*960@15fps)
extra stream(352*288@15fps),
Main stream(1280*720@25fps）
extra stream(352*288@25fps）
NTSC:
Main stream(1280*960@15fps)
extra stream(352*240@15fps)),
Main stream(1280*720@30fps)
extra stream(352*240@30fps)
Video Bit Rate
H.264: 56Kbps-6144Kbps
H.264H: 16Kbps-6144Kbps
H.264B: 56Kbps-6144Kbps
MJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, camera masking.
Lens
C/CS
Lens Interface
Lens is optional.
bezpeka-shop.com
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
3
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 1 to 100;
Area threshold ranges from 1 to 100.
Activation event: video storage, image snapshot, log, email and etc.
Record
and
Backup
Record Priority
Manual>External alarm >Video detect>Schedule
Storage
Management
Support display network storage status
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet.
Network Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
AUX
Interfac
e
Video Output
1-ch analog video output. BNC port.
Network
Interface
1-ch wire Ethernet port. 10/100 Base-T Ethernet
RS485 Port
PTZ Control port. Support various protocols.
General Parameter
Power
Support DC12V power or PoE.
Warning！
Do not connect these two power supplying sources to the device
at the same time; it may result in device damage!
Power
Consumption
2.5W MAX
Working
Temperature
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(mm)
66.2*62.8*131
Weight
196g（Excluding box）
Installation
Installation with the bracket.
Setup
Item
Default Setup
IPC-HF2100 Series
Camera
Conditions
Config File
Normal
Brightness
50
Contrast
50
Saturation
50
Sharpness
50
Anti-flicker
Outdoor
Exposure Mode
Auto
Auto Iris
On
Profile
Auto
Day&night
Auto
bezpeka-shop.com
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
4
Setup
Item
Default Setup
IPC-HF2100 Series
BLC Mode
Off
Mirror
Off
Flip
Off
Profile Management
Normal
Video
Video bit stream
Main
Stream
Bit stream
type
General
Encode mode
H.264
Resolution
720P（1280*720）
Frame Rate
（FPS）
PAL: 25
NTSC:30
Bit Rate Type
CBR
Recommende
d Bit
PAL:1536-6124 Kb/S
NTSC:2048-6144Kb/S
Bit Rate
4096
I Frame
interval
PAL:50
NTSC:60
Watermark
Enable
Watermark
character
DigitalCCTV
Sub
Stream
Enable
Enable
Bit stream
type
General
Encode
mode
H.264B
Resolution
CIF(352*288/352*240)
Frame Rate
（FPS）
PAL: 25
NTSC:30
Bit Rate Type
CBR
Recommend
ed Bit
192-1024Kb/S
Bit Rate
512
I Frame
interval
PAL:50
NTSC:60
Snapshot
Snapshot
Type
General
Image Size
720P（1280*720）
Quality
Better
Bit Rate
Main stream
Interval
1s
Video Overlay
Privacy Mask
Disable
Channel Title
Enable
bezpeka-shop.com
5
Setup
Item
Default Setup
IPC-HF2100 Series
Time Title
Enable
Path
Snapshot
Path
C:\PictureDownload
Record Path
C:\RecordDownload
Network
TCP/IP
Host Name
IPC
Ethernet Card
Wire(Default)
Mode
Static
Mac Address
Device MAC address when it is shipped out of the
factory
IP Version
IPV4
IP Address
192.168.1.108
Subnet Mask
255.255.255.0
Default
Gateway
192.168.1.1
Preferred
DNS
8.8.8.8
Alternate
DNS
8.8.8.8
Enable
ARP/Ping set
device IP
address
service
Enable
Connection
Max
Connection
10
TCP Port
37777
UDP Port
37778
HTTP Port
80
RTSP Port
554
HTTPs On
Disable
HTTPs Port
443
PPPoE
Enable
Disable
Username
none
Password
N/A
DDNS
Server Type
Disable，Dahua DDNS
Server
Address
www.dahuaddns.com
Model
Auto
Domain
Name
“MAC address”. dahuaddns.com
Username
none
IP Filter
Trusted Sites
Disable
SMTP(Email)
SMTP Server
none
bezpeka-shop.com
6
Setup
Item
Default Setup
IPC-HF2100 Series
Port
25
Anonymity
Disable
Username
anonymity
Password
****
Sender
none
Authenticatio
n
none
Title
IPC Message
Attachment
Enable
Mail Receiver
N/A
Interval
0 Second
Health Mail
Disable，interval=60 Seconds
UPnP
Enable UPnP
Disable
SNMP
SNMP Port
161
Read
Community
public
Write
Community
private
Trap Address
N/A
Trap Port
162
SNMP v1
Disable
SNMP v2
Disable
SNMP v3
Disable
Bonjour
Enable
Enable
Server Name
“SN”. It depends on the device.
Multicast
Main
Stream
Enable
Enable
Multicast
Address
239.255.42.42
Port
36666
Extra
Stream
Enable
Disable
Multicast
Address
239.255.42.42
Port
36667
IEEE802
Enable
Disable
Verification
PEAP
Username
none
Password
****
QoS
Real-time
Monitor
0
bezpeka-shop.com
7
Setup
Item
Default Setup
IPC-HF2100 Series
Command
0
Event
Video detect
Motion Detect
Enable
Disable
Anti-dither
5 seconds
Record
Enable
Record Delay
10 seconds
Send Email
Disable
PTZ
Disable
Snapshot
Disable
Video
Masking
Enable
Disable
Record
Channel
Enable
Record Delay
10 seconds
Send Email
Disable
PTZ
Disable
Snapshot
Disable
Abnormity
Disconnection
Enable
Disable
Record
Enable
Record Delay
10 seconds
IP Conflict
Enable
Disable
Record
Enable
Record Delay
10 seconds
Storage
Sched
ule
Holiday
schedule
Record
Disable
Snapshot
Disable
Destination
FTP
Enable
Disable
Server
Address
N/A
Port
21
User Name
anonymity
Password
N/A
Remote
Directory
share
Record Control
Pack Duration
8 minutes
Pre-event
Record
5 seconds
Disk Full
Overwrite
Record Mode
Automatic
Record
Stream
Main Stream
System
General
Local Host
Device Name
Device factory SN
Language
English
Video
Standard
PAL
bezpeka-shop.com
8
Setup
Item
Default Setup
IPC-HF2100 Series
Date and time
Date Format
Y-M-D
Time Format
24H
Time Zone
GMT+08:00
Current Time
Sync
DST Enable
Disable
DST Type
Date
Start Time
00:00:00 January 1st
End Time
00:00:00 January 2
nd
Synchronize
with NTP
Disable
NTP Server
clock.isc.org
Port
123
Update
Period
10 minutes
Account
Anonymous
Login
Disable
PTZ Settings
Protocol
PELCOD
Address
1
Baud Rate
9600
Data Bit
8
Stop Bit
1
Parity
none
Auto Maintenance
Auto Reboot
Enable, Tuesday 02:00
Auto Delete
Old Files
Disable
bezpeka-shop.com
9
SN
Port Name
Function
Connection
Note
1
VIDEO OUT
Video output
port
BNC
Output analog video signal. Can connect to TV
monitor to view video.
2
Indication
Light
Red light
System boot up-red light is on
System upgrades-red light flashes.
System resets-red light is on.
3
DC 12V
Power port
Power port.
Input DC 12V.
4
A
RS485 port
RS485_A port, control external PTZ
B
RS485_B port, control external PTZ
G
GND
RS485 ground port.
IR
IR light port
Connect to peripheral IR light control port.
5
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
Support PoE function.
6
RESET
Reset button
Restore factory default setup.
When system is running normally, press the
RESET button for at least 5 seconds, system
can restore factory default setup.
7 GND port
Please make sure the device is securely
earthed to prevent the thunderstorm strike.
bezpeka-shop.com
2 Structure
2.1 Rear Panel
You can refer to the following figure for rear panel information. See Figure 2-1.
Figure 2-1 Rear panel
Please refer to the following sheet for detailed information.
10
bezpeka-shop.com
2.2 Framework and Dimension
Please refer to the following figure for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.
Figure 2-2 Dimension illustration 1
Figure 2-3 Dimension illustration 2
11
bezpeka-shop.com
3 Device Installation
This series camera support two installation modes: wall mount and pendant mount.
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Figure 3-1 Device installation illustration 1
Step 1
Please select the corresponding installation bracket before your installation.
If it is the cement wall, please install the expansion bolt first. Please make sure the expansion bolt
installation position shall be identical with the bracket. Then you can install the bracket. See Figure 3-1.
If it is the wood wall, you can use the self-tapping bolt to install the bracket directly.
Step 2
Install the camera. Please use the installation pedestal at the bottom of the camera to use the screw to
fix the camera on the bracket.
Step 3
Install the lens to the camera.
Step 4
Connect the auto iris port. See Figure 3-2.
12
bezpeka-shop.com
Figure 3-2 Device installation illustration 2
Step 5
After adjust the camera to proper surveillance position.
Step 6
Secure the knob of the bracket to fix the camera.
13
bezpeka-shop.com
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1 Search interface
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 4-2 Search interface 2
14
bezpeka-shop.com
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-3 Login prompt
After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.
Figure 4-4 Main interface
For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.
15
Input your IP
address here
bezpeka-shop.com
5 Web Operation
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.
5.2 Login and Main Interface
Open IE and input network camera address in the address bar. See Figure 5- 1.
Figure 5- 1 IP address
The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
16
bezpeka-shop.com
Figure 5- 2 Web login
If it is your first time to login in, system pops up warning information to ask you whether install web
plug-in or not after you logged in for one minute. For detailed plug-in installation, please refer to the
Web Operation Manual included in the resource CD.
After you logged in, you can see the main window. See Figure 5- 3.
Figure 5- 3 Web monitoring window
17
bezpeka-shop.com
Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.
18
Bug
I can not upgrade
the device via
network.
When network upgrade operation failed, you can use port 3800 to
continue upgrade.
I can not login the
client-end or the
WEB.
For Windows OS 98 or Windows ME user, if you can not install
the client-end or can not view after the installation. We
recommend the win2000sp4 OS or install the client-end of the
low version.
The Active X control is blocked.
The display card version shall be dx8.1 or higher.
Network connection error occurred.
Invalid network setup.
Invalid user name or password.
I can not play the
download file.
There is no player.
There is no DX8.1 or higher.
For the MEDIA PLAYER, there shall be Div X503Bundle.exe
plugin if you play the .AVI file.
For Windows XP user, you need to install the plugin
DivX503Bundle.exe and ffdsho-2004 1012.exe.
To guarantee
setup update
After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.
Power adapter
The general power adapter can work ranging from 0℃ to 40 ℃. The
device may result in unstable power supply when the temperature
exceeds the working temperature.
Please replace an industry-level power adapter if you are using in
the harsh environments.
bezpeka-shop.com
6 FAQ
19
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board
Component
○ ○ ○ ○ ○
○
Device Case
○ ○ ○ ○ ○ ○
Wire and Cable
○ ○ ○ ○ ○ ○
Packing
Components
○ ○ ○ ○ ○
○
Accessories
○ ○ ○ ○ ○
○
bezpeka-shop.com
Appendix Toxic or Hazardous Materials or Elements
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.
Note
This user’s manual is for reference only. Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks are the properties of their respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website for more information.
Dahua Technology Co.,Ltd
Address：No.1187 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: +86-571-87688883
Fax: +86-571-87688815
Email:overseas@dahuatech.com
Website: www.dahuatech.com
Loading...