Dahua DH-IPC-HDBW11A0EN-W, DH-IPC-HDBW13A0EN-W Quick Start Manual
IR Megapixel Wi-Fi Fixed MiniDome Camera
DH-IPC-HDBW11A0EN-W, DH-IPC-HDBW13A0EN-W
Quick Start Guide
Version 1.0.1
Dahua Technology USA Inc.
Table of Contents
1 Welcome .......................................................................................................................... 1
1.1 Important Safeguards and Warnings .................................................................. 1
Electrical safety ................................................................................................... 1
Environmental Precautions ................................................................................. 2
Operation and Daily Maintenance ...................................................................... 3
Warnings ............................................................................................................. 3
1.2 FCC Information .................................................................................................. 4
FCC Compliance.............................................................................................. 4
1.3 Legal Notices ...................................................................................................... 4
Copyright ............................................................................................................. 4
Trademarks ......................................................................................................... 4
1.4 Disclaimer ........................................................................................................... 4
2 Unpacking ........................................................................................................................ 5
3 Camera Configuration ..................................................................................................... 6
3.1 Camera and Cables ............................................................................................ 6
3.2 Camera Control and Indicators ........................................................................... 7
3.3 Status Indicators ................................................................................................. 7
3.4 Framework and Dimensions ............................................................................... 8
4 Wi-Fi Configuration .......................................................................................................... 9
5 Device Installation ......................................................................................................... 11
1 Welcome
This manual offers reference material and general information about the basic operation,
maintenance, and troubleshooting of the Dahua Multi-Sensor Panoramic Camera. Read, follow, and
retain the following safety instructions. Heed all warning on the unit and in the operating instructions
before operating the unit. Keep this guide for future reference.
1.1 Important Safeguards and Warnings
Electrical safety
Install the unit in accordance with the manufacturer’s instructions and in accordance wi
ap
plicable local codes.
All installation and operation must conform to your local electrical safety codes.
Do not overload outlets and extension cords, which may cause fire or electrical shock.
Do not place the camera near or in a place where the camera may contact overhead power lines,
power circuits, or electrical lights.
Ensure power conforms to SELV (Safety Extra Low Voltage) and that the limited power source is
rated AC 24V as specified in IEC60950-1. (Power supply requirement is subject to the device
label)
.
All input/output ports are SELV circuits. Ensure that SELV circuits are connected only to othe
S
ELV circuits
Ground the unit using the ground connection of the power supply to protect the unit from damage,
especially in damp environments.
Protect the plug and power cord from foot traffic, being pinched, and its exit from the unit.
Units with or without an ON/OFF switch have power supplied to the unit whenever the power
cord is inserted into the power source; however, the unit is operational only when the
witch is in the ON position. The power cord is the main power disconnect device for switching
s
off the voltage for all units.
Operate the unit only from the type of power source indicated on the label. Before proceeding,
disconnect the power from the cable to be installed into the un
For external power supplied units, use only the recommended or approved power supplie
Limited power sources must comply with EN 60950. Substitutions may damage the un
use fire or shock.
ca
For 24 VAC units, voltage applied to the unit’s input power should not exceed ±25%. User-
supplied wiring must comply with local codes (Class 2 power levels). Do not ground the
supply at the terminals or at the unit’s power supply terminal.
Contact the local dealer or the power company to verify the correct power supp
Do not supply power via the Ethernet connection (PoE) when power is already supplied via the
power connecto
Do not attempt to service the unit. Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified personne
.
it.
r.
l.
th
r
ON/OFF
s.
it or
ly.
1
If the unit is damaged and requires service, unplug the unit from the main AC power supply and
from the PoE supply and refer to qualified service personnel. Damage may include, but is not
limited to
Liquid has spilled in or on the uni
The unit has been dropped and the housing is dam
:
The power supply cord or plug is damaged.
t.
An object has fallen on the unit.
aged.
The unit displays a marked change in performance.
The unit does not operate in the expected manner when the user correctly follows the proper
operating procedures
Ensure a service technician uses replacement parts specified by the manufacturer, or that have
.
the same characteristics as the original parts. Unauthorized parts may cause fire, electrica
s
hock, or other hazards. Dahua is not liable for any damage or harm caused by unauthoriz
mo
difications or repairs.
Perform safety checks after completion of service or repairs to the un
Use attachments and accessories only specified by the manufacturer. Any change o
dification of the equipment, not expressly approved by Dahua, could void the warranty
mo
Incorporate a readily accessible disconnect device in the building installation wiring for quick
power disconnect to the camera
Dahua assumes no liability or responsibility for any fire or electrical shock caused by improper
handling or installation
.
.
it.
l
ed
r
.
vironmental Precautions
En
Do not aim the unit at a strong light source or into direct sunlight to focus. A strong light so
y cause overexposure and may affect the longevity of the CCD or the CMOS sensor.
ma
urce
Transport, use, and store the unit within the specified temperature and humidity range.
Do not place the unit in a wet, dusty, extremely hot or an extremely cold environment; and avoid
environments with strong electromagnetic radiation or unstable lightin
Never push objects of any kind into this unit through openings as they may touch dangerous
g.
voltage points or cause a short circuit that may result in fire or electrical shock. Take care to not
spill any liquid on the unit.
Do not use units intended for indoor applications near water, in damp or wet environments, or in
any area classified as a wet location. Do not expose an indoor unit to rain or moisture to reduce
the risk of fire or electric shock.
Do not block or cover any openings in the unit enclosure. These openings are provided for
ventilation to prevent overheating and to ensure reliable operation. Ensure the unit is placed in
an area with adequate ventilation
Do not place the unit near a heat source such as heaters, stoves, radiators or other equipment
that produces he
Pack the unit with standard factory packaging or material of the same quality when transporting
at.
.
the unit.
Take care to avoid heavy stress, violent vibration, or water spills to the camera unit during
transportation, storage, and installation
.
2
Operat
ion and Daily Maintenance
Do not touch the heat dissipation component of the unit. This part of the unit is hot and may
cause a bu
Do not open or dismantle the device; there are no components that a user can fix or replace.
rn.
Opening the unit may cause water leakage or expose components to direct light. Contact the
manufacturer or a qualified service representative to service the camera or to replace a
component, including the desicca
Dahua recommends the use of a thunder-proof device in concert with the un
Do not touch the CCD or the CMOS optic sensor. Use a blower to clean dust or dirt on the lens
surface. Use a dry cloth dampened with alcohol and gently wipe away any dust on the lens
Use a dry soft cloth to clean the unit’s housing. If the unit is particularly dusty, use water to dil
a
mild detergent, apply the diluted detergent to a soft cloth, then gently clean the device. Finally,
nt.
it.
.
use a dry cloth to wipe the unit dry. Do not use a volatile solvent like alcohol, benzene, or thinner;
or use a strong detergent with abrasives, which may damage the surface coating or reduc
orking performance of the unit.
w
e the
Do not touch or wipe a dome cover during installation, this cover is an optical device. Refer to
the following methods clean the dome cover:
Stained with dirt: Use an oil-free soft brush or blower to gently remove the dirt.
Stained with grease or fingerprints: Use a soft cloth to wipe gently the water droplet or the o
om the dome cover. Then, use an oil-free cotton cloth or paper soaked with alcohol or
fr
detergent to clean the lens from the center of the dome to outside. Change the cloth seve
tim
es to ensure the dome cover is clean.
ute
il
ral
Warnings
Change the default password after the initial login to protect the integrity of the network
Use the standard accessories provided by the manufacturer and ensure the unit is installed an
c
ommissioned by qualified professionals.
Protect the lens area from laser radiation when using a laser device to aid in installation a
veling of the unit.
le
.
nd
Do not supply power via the Ethernet connection (PoE) when power is already supplied via the
power connecto
r.
d
3
Loading...