Dahua DHI-LM43-F410 User Manual
UHD LED Monitor
User Manual
DHI-LM43-F410
Please read this manual before use and retain it for future reference.
i
Safety Instructions
Safety precautions and maintenance
WARNING:
exposure to shock, electrical hazards and/or mechanical hazards.
Use of controls, adjustments or procedures other than those specied in this documentation may result in
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning o the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for normal operation.
• Ensure the use of an approved power cord provided by DH at all times. If your power cord is missing, please contact your local
service center.
• Do not subject the display to severe vibration or high impact conditions during operation.
• Do not knock or drop the display during operation or transportation.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your display, grasp
the frame to lift; do not lift the display by placing your hand or ngers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is o.
However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively moist
environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power o immediately and disconnect the power cord. Then remove the
foreign substance or water, and send the unit to the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend using the display in a
location that falls within the following temperature and humidity ranges.
-Temperature: 0-40°C 32-104°F
-Humidity: 20-80% RH
IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a periodic
screen refresh application if the unit will display unchanging static content. Uninterrupted display of still or static images over an extended
period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known phenomenon in LCD
panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after
the power has been switched o.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also not
covered under the terms of your warranty.
Service:
• The casing cover should be opened only by qualied service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in this document, please contact a
technician or your local service center.
iii
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when
the power is o. However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally when you have followed the instructions in this
manual.
• The casing cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning o the display by detaching the power cable or DC power cord, wait for 6 seconds before re-attaching
the power cable or DC power cord for normal operation..
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains
on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen.
This is a well-known phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the
afterimage will disappear gradually over a period of time after the power has been switched o. Be aware that the
after-image symptom cannot be repaired and is not covered under warranty.
CE Declaration of Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States
relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), RoHS directive (2011/65/EU) and Radio
Equipment Directive (2014/53/EU).
This product has been tested and found to comply with the harmonized standards for Information Technology Equipment, these
harmonized standards published under Directives of Ocial Journal of the European Union.
Warning:
This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause radio
interference.
ESD Warnings
When user close to the monitor may cause the equipment discharge and reboot to the display of main menu.
Federal Communications Commission (FCC) Notice (U.S. Only)
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive moisture.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
iv
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment Directive (2014/53/EU). The following test methods have
been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment Directive (2014/53/EU):
- EN60950-1
Safety of Information Technology Equipment
- EN 62311
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic elds (0 Hz-300 GHz)
- EN 300 328 ( For 802.11b/g/n )
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment
operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive
- EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services; Part 17: Specic conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
- EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services; Part 1: Common technical requirements
Canada:
Industry Canada statement:
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement in
v
End-of-Life Disposal
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial
ou
e/ou baterias
rede de assistência técnica
autorizada.
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your
product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please nd out about the local regulations on how to dispose of your old display from your local DH dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information
on recycling contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing
used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are
responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To
determine the locations for dropping o such waste electrical and electronic, contact your local government oce, the
waste disposal organization that serves your household or the store at which you purchased the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.
mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws
Batteries
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste!
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with
legislation.
Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be separated to collect by local service.
vi
Table of contents
Unpacking and installation ................................... 1
1.
1.1. Unpacking ......................................................................................... 1
1.2. Items in the packing case .........................................................1
1.3. Installation precautions .............................................................1
1.4. Hang the monitor on the wall .............................................2
1.4.1. VESA grid plate ..........................................................2
2. Parts and functions .................................................. 3
2.1. Control panel .................................................................................3
2.2. Input/output terminal ................................................................ 4
2.3. Remote Control ...........................................................................5
2.3.1. General functions ..................................................... 5
2.3.2. Install batteries into the remote control ..... 6
2.3.3. Maintenance of the remote control .............. 6
2.3.4. Working scope of the remote control ........6
3. Connect external devices ........................................ 7
3.1. Connect external devices (DVD/VCR/VCD) .............7
3.1.1. Use HDMI video input ..........................................7
3.1.2. Use network interface ........................................... 7
3.2. Connect PC ....................................................................................7
3.2.1. Use HDMI input ........................................................7
3.3. Connect USB .................................................................................8
3.3.1. Use USB device .........................................................8
4. Operation ................................................................. 9
4.1. Media Player introduction: ......................................................9
4.2. PDF reader play ......................................................................... 11
4.3. App customization ................................................................... 13
4.3.1. Operation on the OSD menu: ...................... 13
5. Compatibility of the USB device ............................ 15
6. Input mode ............................................................ 17
7. leaning and Troubleshooting ................................. 18
7.1. Cleaning ..........................................................................................18
7.2. Troubleshooting ......................................................................... 19
8. Technical specification ........................................... 20
vii
1. Unpacking and installation
1.1. Unpacking
• This product is packed in a paper packing case and comes with standard accessories.
• Any other optional parts are individually packed.
• Considering the size and weight of the monitor, it is recommended to move this monitor by two persons.
• Please conrm that items are complete and intact after opening the packing case.
1.2. Items in the packing case
Please conrm that the packing case contains the following items:
• LCD monitor
• Remote control
• Instructions
• Power cord
• HDMI wire
• Logo
* The supplied power cord varies depending on destination。
Remote Control
UHD LED Monitor
User Manual
DHI-LM43-F410
User Manual
Power Cord
HDMI Cable
Logo
Notes:
• For all other regions, the power cords shall be matched with the AC voltage of the power socket, conform to the regulations of the
relevant laws of the countries/territories, and pass certication. ( Types H05VV-F, 2G or 3G 0.75 or 1mm2 shall be used.)
• You can keep the packing case and packaging materials for later transport of the monitor.
1.3. Installation precautions
• This product belongs to high-power-consumption products. Please always use the plug specially designed for this product. If you
need to extend the wire, please consult your service provider.
• This product should be installed on a plane to avoid overturn. The rear part of this product should be kept away from the wall at a
certain distance so as to maintain proper ventilation. This product shall not be installed in the kitchen, bathroom or any other locations
with high humidity, to avoid shortening the service life of the electronic components.
• This product works only at an altitude below 3000m. If the installation site is higher than 3000m, some abnormalities may occur.
1
1.4. Hang the monitor on the wall
Table
In order to install the monitor on the wall, you must prepare a set of standard wall-hanging kit (separately purchased). You are
recommended to use the mounting plate which conforms to the TUV-GS and/or UL1678 standard.
Protective Sheet
VESA Grid
1. Spread the protective lm (wrapped on the monitored during packing) on the desk, and place the monitor with its front face down on
the protective lm to avoid scratching the screen.
2. Make sure all accessories (hanging rack, lifting rack, desk base, etc.) for installing the monitor have been prepared.
3. Follow the use instructions of the base tting kit during the operation. In the case of disobedience to the correct assembling steps,
damage to devices or injuries to users or installation persons may be caused. Damage caused by incorrect installation is not included
in the product warranty.
4. Use M6 assembling screws (with a length 10mm greater than the thickness of the assembling rack to x the wall-hanging kit), and
fasten the screws.
1.4.1. VESA grid plate
DHI-LM43-F410 400(H) x 400(V) mm
Caution:
Prevent the monitor from falling down:
• In the case of wall installation or suspended installation, it is recommended to use the metal assembling rack available on the market
to install the monitor. Refer to the guide attached to the assembling rack for specic installation instructions.
• In order to lower the probability that the monitor falls down and results in personal injuries and property loss under the condition of
earthquake or other natural disasters, please do consult the assembling rack manufacturer to conrm the installation position.
Ventilation requirements for enclosed space
In order to ensure normal heat dissipation, sucient space from items to
four sides shall be kept, as shown in the gure below.
100 mm 100 mm
100 mm
100 mm
2
Loading...