Dahua DH-HAC-PFW3601N-A180 Quick Start Manual

Multi-sensor HDCVI Panoramic IR Bullet Camera

DH-HAC-PFW3601N-A180

Quick Start Guide

Version 001.001 Dahua Technology USA Inc.

Table of Contents

1 Welcome........................................................................................................................ 1

1.1 Important Safeguards and Warnings ................................................................. 1

Electrical safety ................................................................................................. 1

Environmental Precautions ............................................................................... 2

Operation and Daily Maintenance ..................................................................... 3

Lifting Appliance Requirement .......................................................................... 3

Warnings ........................................................................................................... 3

1.2 FCC Information ................................................................................................ 4

FCC compliance： ............................................................................................ 4

1.3 Legal Notices .................................................................................................... 4

Trademarks ....................................................................................................... 4

1.4 Disclaimer ......................................................................................................... 5

2 Unpacking...................................................................................................................... 6

3 Installation and Configuration ........................................................................................ 7

3.1 External Cable .................................................................................................. 7

Cable Connections ............................................................................................ 7

Alarm I/O Port Configuration ............................................................................. 7

3.2 Framework and Dimensions ............................................................................. 7

3.3 Alarm Setup ...................................................................................................... 8

Alarm Input ........................................................................................................ 8

Alarm Output ..................................................................................................... 8

4 Device Installation ......................................................................................................... 9

4.1 Installing the Camera ........................................................................................ 9

5 Setting Camera Parameters ........................................................................................ 11

6 Camera Maintenance .................................................................................................. 14

6.1 Optical Components ........................................................................................ 14

6.2 Camera Body .................................................................................................. 14

1 Welcome

This manual offers reference material and general information about the basic operation, maintenance, and troubleshooting of the Dahua Multi -Sensor Panoramic Camera. Read, follow, and retain the following safety instructions. Heed all warning on the unit and in the operating instructions before operating the unit. Keep this guide for future reference.

1.1 Important Safeguards and Warnings

Electrical safety

• Install the unit in accordance with the manufacturer’s instruction s and in accordance with applicable local codes.

• All installation and operation must conform to your local el ect rical safety codes.

• Do not overload outlets and extension cords, whi ch may cause fire or electrical shock.

• Do not place the camera near or in a place where the camera may contact overhead power lines,

power circuits, or electrical lights.

• All input/output ports are SELV circuits. Ensure t hat S ELV circuits are connected only to other SELV circuits.

• Ground the unit using the ground connection of the power supply to prot ect the unit from damage, especially in damp environments.

• Protect the plug and power cord from foot traffic, being pinched, and its exit from the unit.

• Units with or without an ON/OFF switch have power supplied to the unit whenever the power

cord is inserted into the power source; however, the uni t is operational only when the ON/OFF switch is in the ON position. The power cord is the main power disconnect device for switching off the voltage for all units.

• Operate the unit only from the type of power source indi cat ed on the label. Before proceeding, disconnect the power from the cable to be installed into t he unit.

• For external power supplied units, use only the recomm ended or approved power supplies.

• Limited power sources must comply with EN 60950. S ubst itutions may damage the unit or

cause fire or shock.

• For 24 VAC units, voltage applied to the unit’s input power sh oul d not exceed ±25%. User-

supplied wiring must comply with local codes (Class 2 power levels). Do not ground the supply at the terminals or at the unit’s power supply t ermi nal .

• Contact the local dealer or the power company to verify the correct power supply.

• Do not supply power via the Ethernet connection (PoE) when power is already supplied via the

power connector.

• Do not attempt to service the unit. Opening or removi ng cov ers may expose you to dangerous voltage or other hazards. Refer all servicing to qualifi ed personnel.

• If the unit is damaged and requires service, unplug the unit from the main AC power supply and from the PoE supply and refer to qualified service per sonnel. Damage may include, but is not limited to:

• The power supply cord or plug is damaged.

• Liquid has spilled in or on the unit.

• An object has fallen on the unit.

• The unit has been dropped and the housing is damaged.

• The unit displays a marked change in performance.

• The unit does not operate in the expected manner when t he user correctly follows the proper

operating procedures.

• Ensure a service technician uses replacement pa rt s specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized parts may cause fire, electrical shock, or other hazards. Dahua is not liable for any dam age or harm caused by unauthorized modifications or repairs.

• Perform safety checks after completion of service or repairs to the unit.

• Use attachments and accessories only specified by the m anuf acturer. Any change or

modification of the equipment, not expressly approved by Dahua, could void the warranty.

• Incorporate a readily accessible disconnect device in the building installation wiring for quick power disconnect to the camera.

• Dahua assumes no liability or responsibility for any fire or electrical shock caused by improper handling or installation.

Environmental Precautions

• Do not aim the unit at a strong light source or into direct sunlight to focus. A strong light source may cause overexposure and may affect the longevity of the CCD or the CMOS sensor.

• Transport, use, and store the unit within the specified temperature and humidity range.

• Do not place the unit in a wet, dusty, extremely hot or an extremely cold environment; and avoid

environments with strong electromagneti c radiation or unstable lighting.

• Never push objects of any kind into this unit through openi ngs as they may touch dangerous voltage points or cause a short circuit that may resul t in fire or electrical shock. Take care to not spill any liquid on the unit.

• Do not use units intended for indoor applications near water, in damp or wet environments, or in any area classified as a wet location. Do not expose an indoor unit to rain or moisture to reduce the risk of fire or electric shock.

• Do not block or cover any openings in the unit enclosure. These openings are provided for ventilation to prevent overheating and to ensure reliable operation. Ensure the unit is placed in an area with adequate ventilation.

• Do not place the unit near a heat source such as heaters, st oves, radiators or other equipment that produces heat.

• Pack the unit with standard factory packaging or material of the same quality when transporting the unit.

• Take care to avoid heavy stress, violent vibration, or water spills to the camera unit during transportation, storage, and installation.

Operation and Daily Maintenance

• Do not touch the heat dissipation component of the unit. This part of the uni t is hot and may cause a burn.

• Do not open or dismantle the device; there are no components that a user can fix or replace. Opening the unit may cause water leakage or expose components to di rect light. Contact the manufacturer or a qualified service representative to s ervice the camera or to replace a component, including the desiccant.

• Dahua recommends the use of a thunder-proof device in concert with the unit.

• Do not touch the CCD or the CMOS optic sensor. Use a blower to clean dust or dirt on the lens

surface. Use a dry cloth dampened with alcohol and gent ly wipe a way any dust on the lens.

• Use a dry soft cloth to clean the unit’s housing. If the unit is particul arly dusty, use water to dilute a mild detergent, apply the diluted detergent to a soft cloth, then gently clean the device. Finally, use a dry cloth to wipe the unit dry. Do not use a volatile solvent like alcohol, benzene, or thinner; or use a strong detergent with abrasives, which may damage t he surface coating or reduce the working performance of the unit.

• Do not touch or wipe a dome cover during installation, this cover is an optical device. Refer to the following methods clean the dome cover:

• Stained with dirt: Use an oil-free soft brush or blower to gently remove the dirt.

• Stained with grease or fingerprints: Use a soft cloth t o wipe gently the water droplet or the oil

from the dome cover. Then, use an oil-free cotton cloth or paper soaked with alcohol or detergent to clean the lens from the center of the dome t o out side. Change the cloth several times to ensure the dome cover is clean.

Lifting Appliance Requirement

• Select the proper installation mode and use the proper lifting device to safely lift the camera at the installation site.

• Ensure that the lifting device has the proper capacity t o reac h the installation height.

• Use the lifting device in accordance with its operating instructions and abide by the device’s

safety precautions.

Warnings

• Change the default password after the initial login to protect the integrity of the network.

• Use the standard accessories provided by the manufacturer and ensure the unit is installed and

commissioned by qualified professionals.

• Protect the lens area from laser radiation when using a laser device to aid in installation and leveling of the unit.

• Do not supply power via the Ethernet connection (PoE) when power is already supplied via the power connector.

1.2 FCC Information

This device complies with part 15 of the FCC Rules. Operat i on i s subject to the following two conditions:

• This device may not cause harmful interference;

• This device must accept any interference received, i ncluding interference that may cause

undesired operation.

FCC compliance

：

This equipment has been tested and found to comply wit h the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to prov i de reasonable protection against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, t he user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and r eceiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

1.3 Legal Notices

Trademarks

All hardware and software product names used in this doc um ent are likely to be registered trademarks and must be treated accordingly.

+ 11 hidden pages

Dahua DH-HAC-PFW3601N-A180 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual